21 November 2017 Linear CCD array TH-7834B performances near 10 MHz
Author Affiliations +
Proceedings Volume 10568, International Conference on Space Optics — ICSO 2004; 105681U (2017) https://doi.org/10.1117/12.2308031
Event: International Conference on Space Optics 2004, 2004, Toulouse, France
Abstract
The spatial resolution improvement of Earth observation satellites implies higher CCD readout frequences (at the moment for an instrument such as SPOT 5, typical CCD readout frequency reaches 5MHz for an Earth resolution of 3.5 m and a 60 km swath).

The spatial resolution improvement of Earth observation satellites implies higher CCD readout frequencies (at the moment for an instrument such as SPOT 5, typical CCD readout frequency reaches 5MHz for an Earth resolution of 3.5 m and a 60 km swath). Soon, as we try to increase the spatial resolution without degradation of the swath, reading frequency of 10 MHz will be required. Furthermore, this output data rate needs to be achieved with Correlated Double Sampling (C.D.S) which remains the only way to deliver good performances in term of signal-to-noise ratio.

This poster shows results of measurements at 9.25 MHz readout frequency on a linear CCD array ATMEL TH-7834B, already used in spatial instrument SPOT 5 at lower frequencies.

The most important parameters to measure were :

  • - the shape of the CCD output signal, to determine the length of the area available to sample the signal,

  • - linearity and transfer efficiency, with respect to the irradiance of the CCD,

  • - the stability of the performances in case of phase shift of the CCD and acquisition clocks.

Measurement bench

First of all, precise measurements require a bench to catch CCD signal et measure the linearity error.

A specific electronic was designed, to allow a maximum bandwidth, and a fine tuning of the CCD clocks was performed, to optimize the shape of the output signal. Our video chain was measured for a differential non linearity of +/- 0.3 LSB, and a global non linearity of 2 LSB (with a 12 bit resolution) at 10 MHz frequency.

CCD signal shape

The following figures show the reference and video levels at 9.25 MHz, both for a dark pixel, and an illuminated pixel. They exhibit a useful length of more than 10ns for the sampling.

Some improvements of the CCD internal output amplifier are possible to more improve the speed and reduce the ripple of the output signal.

00367_PSISDG10568_105681U_page_2_1.jpg

The problem is obviously : How precise have to be the clock phases, in order to maintain a long enough length for the video and reference level ? In other words : what kind of drift is authorized for the slope of the clocks (of the CCD and of the acquisition chain) ? The following paragraphs give some answers to this question.

Linearity

We tested the degradation of the linearity between pixels at 5 MHz and pixels at 9.25 MHz

Linearity error is given by

00367_PSISDG10568_105681U_page_2_2.jpg

where

  • - Vccd (resp Vobsc) is the result of a CDS (Correlated double sampling) of the CCD signal for illuminated pixels (resp dark pixels),

  • - Eel is the irradiance on the illuminated pixels (in W/m2),

  • - the “ref” values are referenced to the middle of the dynamic (here 500 mV for Vccd).

The issue was of course to know what kind of margin existed for the clock signals, in order to maintain the linearity error at low level.

So we simulated 2 kinds of time shift of the sampling clock signal :

  • - a long term shift, simulated with a similar shift applied to illuminated pixel and dark pixels : this case simulate a long term shift in orbit, due to thermal phenomenon, or radiation effects,

  • - a short term shift, simulated with a shift applied only to illuminated pixels, when dark pixels was sampled with the optimized clock phase : this case simulate the short term jitter, which is generally very small and well characterized by ground measurements.

The results are the following for the sampling signal of the CCD video level. The curves are given :

  • - with respect to the output CCD level (Vccd-Vobsc),

  • - for 3 different delays of the sampling signal : the middle one is the best.

00367_PSISDG10568_105681U_page_3_1.jpg
00367_PSISDG10568_105681U_page_3_2.jpg

The results are : a long term shift of 10 ns peak to peak for the sampling signal induces a very small degradation of the linearity, even at low signal level : so the authorized shift for the sampling signal can be so.

A short term shift induces a fast degradation of the linearity at low level. Hopefully, in the currently used acquisition chains, this short term jitter is very low, and is not supposed to increase dramatically in orbit.

Similar investigations has been carried out for the other clocks (sampling signal of reference level, CCD clocks), leading to similar results :

  • - long term drift of about 10 ns are possible without significant degradation of the linearity,

  • - short term jitter has to be limited under 2 ns.

Transfer inefficiency

No degradation of this parameter has been observed for clock frequencies between 5 MHz and 9.25 MHz.

© (2017) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
Alain Bardoux, Alain Bardoux, Jean-Jacques Quicot, Jean-Jacques Quicot, } "Linear CCD array TH-7834B performances near 10 MHz", Proc. SPIE 10568, International Conference on Space Optics — ICSO 2004, 105681U (21 November 2017); doi: 10.1117/12.2308031; https://doi.org/10.1117/12.2308031
PROCEEDINGS
3 PAGES


SHARE
RELATED CONTENT

In-line digital holography with double knife edge
Proceedings of SPIE (June 20 2015)
Fast online detection of body defect of glass containers
Proceedings of SPIE (November 30 2011)
X ray imaging in an environment with high neutron background...
Proceedings of SPIE (September 13 2011)
Artifacts in Digital Images
Proceedings of SPIE (November 20 1980)
Design of the IMACS 8Kx8K dewar and detector system
Proceedings of SPIE (March 06 2003)

Back to Top