Translator Disclaimer
Open Access Presentation + Paper
9 September 2019 A compact light source providing high-flux, quasi-monochromatic, tunable X-rays in the laboratory
Author Affiliations +
There is a large performance gap between conventional, electron-impact X-ray sources and synchrotron radiation sources. Electron-impact X-ray sources are compact, low to moderate cost, widely available and can have high total flux, but have limited tunability (broad spectrum bremsstrahlung plus fixed characteristic lines) and low brightness. By contrast, synchrotron radiation sources provide extremely high brightness (coherent flux), are tunable and can be monochromatized to a very high degree. However, they are very large and expensive, and typically operated as national user facilities with limited access. An Inverse Compton Scattering (ICS) X-ray source can bridge this gap by providing a narrow-band, high flux and tunable X-ray source that fits into a laboratory at a cost of a few percent of a large synchrotron facility. It works by colliding a high-power laser beam with a relativistic electron beam, in which case the backscattered photons have an energy in the X-ray regime. This paper will describe the working principle of the Lyncean Compact Light Source, a storage-ring based ICS source, its unique beam properties and recent developments that are expected to increase flux and brightness by an order of magnitude compared to earlier versions. Furthermore, it will illustrate how such an X-ray source can be the cornerstone of a local X-ray facility serving applications from diffraction and imaging to scattering and spectroscopy. An overview of demonstrated and potential applications will be provided.
Conference Presentation



Conventional electron-impact X-ray sources have been in use since the discovery of X-rays by Röntgen in 1895.1 They work by accelerating an electron beam onto a metal target (anode), whereby X-rays are generated by two mechanisms resulting in the well-known spectrum of such X-ray sources: Bremsstrahlung (“breaking radiation”) generates a continuous spectrum of X-rays with an energy up to the acceleration voltage of the electrons (typically tens to hundreds of keV), while X-ray fluorescence of the atoms in the target generates characteristic lines at specific energies defined by the X-ray emission lines of the target material chosen (typically a few keV to tens of keV).

The X-ray flux or brightness (here loosely defined as flux per source area) is limited by the power, and thus heat load, that the target can tolerate before melting. The most basic type of X-ray source works in reflection geometry, where the X-rays are extracted from the same surface of the (thick) target that the electron beam impinges on. This geometry allows for relatively high power, but the spread of the electrons in the target limits the spot size achievable to the range of 5-10 µm in the case of microfocus reflection sources (high power sources have spot sizes larger than 1 mm). Alternatively, in micro/nanofocus transmission sources, the target is a thin metal film on a low-absorbing substrate, and the X-rays are extracted from the opposite side of the target. The limited spread of the electron beam in the thin target allows for spot sizes below 1 µm (albeit at very low power), and the geometry allows for very short working distances, useful for applications like micro-CT. To further overcome the limits of heat load on a stationary target, rotating anode sources2 have been developed, where the heat load is spread over a larger surface, allowing for much higher power. More recent, advanced developments include liquid metal jet sources3,4 and structured anode sources,5 but all these developments are reaching the physics limit of what can be achieved with electron-impact sources.

Conventional X-ray sources are ubiquitous and widely commercially available. They are compact, can easily be integrated into cabinet-sized or even desktop instruments, and are affordable (typically from a few tens of thousands of US dollars for simple reflection sources to a few hundred thousand for rotating anode, liquid metal or structured anode sources). They are integrated into many turn-key X-ray instruments serving a wide range of applications, such as:

  • Medical applications, e.g. standard X-ray, dental X-ray and computed tomography (CT)

  • Commercial applications, e.g. baggage inspection

  • Industrial applications, e.g. 2D/3D inspection

  • Research applications, e.g. X-ray diffraction (XRD), X-ray fluorescence (XRF), Small Angle X-ray Scattering (SAXS), X-ray Microscopy (XRM), or micro-CT

By contrast, synchrotron X-ray sources are based on particle accelerators, where a high-energy (GeV-range) electron beam is circulated in a storage ring. X-rays are generated by transverse acceleration (deflection) of the electron beam in magnetic fields, both in the bending magnets that keep the beam on its quasi-circular trajectory, and in periodic magnet structures (wigglers and undulators), where the X-rays generated by multiple deflections add up to generate even brighter beams (see Figure 1).

Figure 1.

Illustration of an undulator.6 An undulator is a periodic structure of dipole magnets (1). An electron beam (2) traversing the structure undergo undulations and produce radiation (3).


Synchrotron sources generate collimated X-ray beams with much higher brightness than is possible with conventional X-ray sources. A more stringent definition of brightness than the one used above is X-ray flux per source area, per solid angle, and per energy band, i.e. it is a measure of beam size achievable, collimated flux and spectral density. While the spectrum from bending magnets and wigglers is broad, the one from undulators is narrower and consists of multiple harmonics. In either case, the high inherent brightness of synchrotrons allows the X-ray beam to be monochromatized to a high degree using crystal or multilayer monochromators. The energy is tunable continuously over a wide range, which can range from well below the X-ray range (IR, UV) to the soft X-ray (hundreds of eV) and hard X-ray (>100 keV) range, depending on the synchrotron design. Synchrotron facilities typically have tens of beamlines providing access to a wide range of X-ray techniques from diffraction and imaging to spectroscopy and scattering.

However, synchrotron facilities require a large investment (hundreds of millions of US dollars) and are therefore typically government funded and operated. Access is provided through competitive proposal systems and limited to a few days of beam time per user per year, although commercial access-for-fee is also available at most facilities. Many beamlines are highly oversubscribed so that only a fraction of the proposals submitted get beamtime assigned. This, along with the limited number of synchrotrons available (about 50 worldwide), presents a barrier of entry that makes synchrotrons inaccessible to many researchers. Furthermore, a single allotment of a few days of beamtime precludes longitudinal experiments, where the same sample needs to be imaged repeatedly over a longer period. Additional restrictions may exist in the ability to measure restricted samples with radiological, biological or other hazards, or where certain types of experimental apparatus are required.

Table 1 provides a qualitative comparison of the X-ray beam properties, general accessibility and applicability to different X-ray techniques between electron-impact and synchrotron sources.

This discussion of conventional and synchrotron X-ray sources indicates that there is a need for X-ray sources that bridge the gap between the two, both in terms of performance (X-ray beam characteristics) and accessibility and price. An X-ray source that provides synchrotron-like beam properties (high flux, monochromaticity, tunability, partial coherence) and that can operate in a local laboratory provides many opportunities by broadening access to advanced X-ray techniques, enabling longitudinal experiments and accommodating restrictive samples. This provides a pathway to industrial and clinical applications that are not feasible at synchrotrons because of the restrictive access model. Furthermore, having a compact source in a local lab provides a synchrotron-like environment that enables training opportunities in the areas of accelerators and instrumentation as well as X-ray techniques and applications.

In this paper we present the Lyncean Compact Light Source (CLS), an X-ray source based on Inverse Compton Scattering (ICS) that bridges the gap between conventional X-ray sources and synchrotron facilities. The idea of a laser-electron storage ring for the generation of X-rays was conceived by Huang and Ruth in 1997.7 Lyncean Technologies, Inc. was founded in 2002 to develop and commercialize the Compact Light Source. X-ray experiments were performed starting in 2007.818 The first commercial system was delivered to a consortium of the Technical University of Munich (TUM) and the Ludwig-Maximilians-Universität (LMU) and commissioned in 2015. Together with a beamline and two biomedical imaging end-stations developed by TUM researchers, this facility is known as the Munich Compact Light Source (MuCLS).19,20 The MuCLS has been operating with a high degree of uptime since then and has enabled many scientific experiments and publications.2131

Table 1.

Qualitative comparison of electron-impact and synchrotron X-ray sources. The Lyncean Compact Light Sources bridges the gap for most of these properties.

 Electron-impact X-ray sourcesSynchrotron X-ray sources
Beam properties  
X-ray fluxTotal flux can be highHigh
BrightnessLow (moderate for characteristic lines with rotating anodes, liquid metal jet or other advanced sources)High
Spectrum and monochromaticityContinuum with characteristic lines Characteristic lines can be monochromatized (isolated) to some degreeBroad continuum (bending magnet, wiggler) to narrow peaks (undulator) Can be monochromatized to high degree
TunabilityLimited (choice of target material defines characteristic line energies; acceleration voltage sets peak and maximum energy of continuum)Continuously tunable over wide range
CoherenceLow (moderate coherence for nanofocus or structured anode sources)High
Beam divergence / beam sizeLargeSmall
SizeCompact (cabinet / desktop)Very large (stadium-size)
CostLow to moderateHigh
AccessibilityCommercially available for any labTypically government-funded and operated, limited access Only ~50 synchrotrons worldwide
X-ray techniques and application-specific performanceGenerally, most X-ray techniques such as diffraction, imaging, spectroscopy or scattering can be performed with both electron-impact and synchrotron sources. While the details depend on the technique and the specific application needs, generally the following guidelines apply:
 Longer measurement timesShorter measurement times
 Lower resolution and sensitivityHigher resolution and sensitivity
 Suitable where fixed energy or polychromatic beam is acceptableRequired where tunability and/or monochromaticity is required
 Advantageous for large sample sizes (e.g., imaging of large components and low or moderate resolution)Large samples require scanning. Better suited for high resolution work on smaller samples
 Generally not suited for coherence-based applications, although phase-contrast imaging is possibleWell suited for applications with even the highest coherence requirements (e.g. nanofocusing or coherent imaging)




The wave picture – how to shrink an electron storage ring and still generate multi-keV X-rays

To calculate the X-ray wavelength for a permanent magnet undulator, the undulator equation for the fundamental on-axis can be written as32


where λx,1 is the X-ray wavelength of the fundamental, K is the deflection parameter (for undulators, K ≲ 1), γ = Ee/E0 is the Lorentz factor (e-beam energy Ee in units of electron rest mass energy E0 = 0.511 MeV) and λuis the period of the undulator. For a weak undulator, K ≪ 1 so that


With λu = 1 cm and γ = 6850 (electron beam energy Ee = 3.5 GeV), the X-ray wavelength becomes λx,1 = 0.11 nm, which corresponds to X-ray energy of Ex = 11.6 keV. Such storage rings typically have a circumference of several hundred meters. Now, how can we shrink the synchrotron storage ring and still generate multi-keV X-rays? Considering that the magnetic field strength of the bending magnets stays the same, the achievable bending radius is proportional to the e-beam energy. To reduce the circumference of the storage ring by a factor of 100 to a few meters, we need to reduce the e-beam energy, or γ, by the same amount to about 35 MeV. Consequently, we would need to reduce the undulator wavelength by 10,000 to maintain the same X-ray energy. This can be achieved by using a laser beam with a wavelength around 1 µm as an undulator – the electromagnetic field of the laser will “undulate” the electron beam in the same way as the periodic arrangement of permanent magnets in a conventional undulator. In fact, the undulator equation for peak photon energy on axis for a laser undulator can be written as33


The additional factor of 2 in the denominator comes from the fact that the undulator (laser) field is not stationary, but counter-propagates the electron beam at the speed of light. Table 2 below summarizes typical storage ring parameters of synchrotrons and the Lyncean Compact Light Source.

Table 2.

Typical storage ring parameters of synchrotrons and the Lyncean Compact Light Source

 SynchrotronCompact LightSource Scale factor
Storage ring diameter~60-300 m~1 m~100x
Electron beam energy2-8 GeV25-50 MeV~100x
Bending magnet field strength~1 T~1 T~same
Bending magnet emission*X-ray (~keV)Infrared (~0.1 eV)~10,000x
Undulator period~1 cm~1 μm~10,000x
Undulator typePermanent magnetLaser 


At a traditional synchrotron, typically both bending magnet and undulator / wiggler emission is used for experiments. At the CLS, only the laser undulator radiation is used.


The particle picture – inverse Compton scattering

In the particle picture, this process is known as inverse Compton scattering, where photons in the visible range are backscattered from a beam of relativistic electrons (see Figure 2a). The energy of the backscattered photon for arbitrary angles can be calculated as33

Figure 2.

(a) Schematic of the inverse Compton scattering process. A laser photon collides with a relativistic electron. The backscattered photon has an energy in the X-ray range. (b) Peak X-ray energy (for head-on collision) as a function of electron energy with a laser wavelength of 1064 nm.


where Ex is the X-ray energy of the backscattered photon, EL is the laser photon energy, β = v/c is the ratio of velocity v of the electron to the speed of light c and θi and θf are incident and final scattering angles, respectively. For a head-on collision (θi = 180°), small scattering angles (θf ≪ 1), ELE0 and γ ≫ 1 this simplifies to


The peak X-ray energy for a backscattered photon (θf = 0°) becomes


in analogy to Eq (3) above. Figure 2b plots peak X-ray energy as a function of electron energy for a laser wavelength of 1064 nm.

If we consider only on-axis electrons (θi = 180°), we can plot the X-ray energy dependence on scattering angle θf from Eq. (5) as shown in Figure 3a. This figure shows how the X-ray energy drops as we move off-axis and indicates how the width of the spectrum depends on the beam divergence that is collected. In practice, the divergence is typically restricted to a few milliradians, which keeps the bandwidth to a few percent.

Figure 3.

(a) X-ray energy of the scattered photons as a function of scattering angle θf for on-axis electrons (θi = 180°), laser wavelength 1064 nm and electron energy 44.3 MeV (maximum X-ray energy 35 keV). In practice, an aperture typically restricts the beam divergence delivered to the experiment to a few milliradians (gray band), so that the resulting beam has a bandwidth of a few percent. (b) Normalized flux density, i.e. probability distribution for the energy (and corresponding scattering angle) of the scattered X-rays.


The case above represents the lowest bandwidth possible in the ideal case of a parallel, monoenergetic electron beam. For an electron beam with finite emittance and energy spread, the spectrum of the X-ray beam is given by the convolution of the scattering angles collected (typically defined by an aperture) and the range of angles of incidence of the electron beam (defined by the e-beam emittance and focusing strength), the energy spread and the flux density32 (Figure 3b). Measured spectra for the Lyncean Compact Light Source, which agree well with calculated spectra obtained from Monte-Carlo simulations, are provided in Figure 6 below.

Figure 6.

(a) Measured X-ray spectra of the CLS at peak energies 15.2 keV, 24.8 keV and 35.0 keV. The two peaks in the 35 keV spectrum at about 25 and 28 keV are detector artifacts and not part of the CLS X-ray spectrum. (b) Image of the CLS X-ray beam at 16.6 m distance from the interaction point. Both figures reproduced from Ref.20 with permission of the International Union of Crystallography.




The photon flux x that can be generated by the inverse Compton process is given by the luminosity formula:


Where 00008_PSISDG11110_1111003_page_6_2.jpg is the Thomson cross-section and 𝓛0 is the luminosity:


Here, fcoll is the collision frequency, NL and Ne are the number of laser photons and electrons in each pulse, respectively, and σe.l are the transverse spot sizes of the electron and laser beam, respectively, assuming round beams.

The luminosity equation above shows that the X-ray flux in an inverse Compton scattering X-ray source can be optimized by the following:

  • fcoll: maximize the photon-electron collision frequency

  • Nl : maximize laser pulse energy

  • Ne: maximize electron bunch charge

  • σe,l: match and minimize size of e-beam and laser waist


LINAC-based vs. storage-ring-based ICS sources

In general, two approaches exist for ICS sources: linear-accelerator (LINAC) based and storage-ring based.

In the LINAC scheme, low emittance electron bunches from a linear accelerator collide directly with a high intensity pulsed laser, which may be recirculated to enhance flux. The interaction frequency is limited by the repetition frequency of the electron source, which is typically in the tens to hundreds of Hz range (although schemes exist to increase this to the kHz range by using pulse trains). To maximize luminosity, the number of electrons per bunch and the laser pulse energy are both increased, and both beams focused to small spots, until practical limits are reached. This approach may be useful for pulse-probe type experiments because they produce low repetition rate X-ray pulses with a large photon count in each pulse and small spot size. LINAC-based approaches are less appropriate for high average intensity applications due to the low repetition rates. Also, since the electron beam is discarded after a single interaction, the power and shielding requirements are substantial, or complex energy-recovery schemes need to be implemented. While several LINAC-based ICS sources have been proposed or are under development,3439 to date none is operational as a user facility for X-ray experiments.

Storage-ring-based sources store the electron bunches on a closed orbit and compensate slow charge decay with infrequent charge injection. Unlike a LINAC source, the electrons are recirculated and can interact over many turns, which keeps power consumption low. The interaction frequency is typically around five orders of magnitude higher (65 MHz in the case of the Lyncean Compact Light Source) which makes them quasi-continuous and able to produce much higher average flux and brightness. The cavity-drive laser is matched to the many MHz rate through the use of a CW mode-locked laser which is frequency-locked to a high finesse optical cavity (pulse stacking). This cavity technology provides a demonstrated way to circulate up to hundreds of kW of optical pulse power. Besides the Lyncean Compact Light Source, which is commercially available, several storage-ring-based ICS sources are proposed or under development.4042 A general overview of ICS based sources is provided, for example, in References 43,44.




System overview and design

A simplified schematic of the Lyncean CLS is shown in Figure 4, and a photograph in Figure 5. An electron pulse is generated using an RF photocathode gun. A linear accelerator of about 5 m in length accelerates the pulse to energies of 25 to 50 MeV. The pulse is then injected into a storage ring of about 4.6 m circumference. Only one electron pulse circulates in the storage ring at a given time. This pulse is dumped and refreshed at a rate of a few tens of Hz.

Figure 4.

Simplified schematic of the Lyncean Compact Light Source. Electron bunches are generated in the RF photocathode gun, accelerated in the linear accelerator and injected into the electron storage ring. A mode-locked IR laser resonantly drives an optical cavity, shown here schematically as a two-mirror cavity. Electrons and laser pulses collide in the interaction region and generate a collimated, quasi-monochromatic X-ray beam.


Figure 5.

Photograph of the Lyncean Compact Light Source.


The storage ring is configured in a “racetrack” configuration (two 180-degree arcs and two straight sections). One straight section is used for the injection and electron beam dump. In the other straight section (called the Interaction Region), which also serves as one section of a bow-tie optical cavity (see below), the electron beam is focused to a small spot and interacts with an optical pulse to generate X-rays via inverse Compton scattering.

A mode-locked IR laser with wavelength 1 µm resonantly drives the optical cavity to build up a high-power laser pulse via pulse-stacking. The enhancement cavity has a gain of about 10,000, so that a 30 W average power laser builds up to about 300 kW of circulating power. The storage ring and the optical cavity share a common leg, where the electron bunch and the laser pulse collide at the interaction point, producing an X-ray pulse directed in a narrow cone in the same direction as the electron beam. The solid angle of the X-ray beam is determined by a limiting aperture at the optical mirror, and the X-rays are coupled out of the vacuum system through a thin membrane.

While the laser wavelength is fixed, the energy of the X-rays produced can be tuned by changing the energy of the electron beam. This is done by changing the magnetic lattice of the storage ring, i.e., by adjusting the magnet currents to provide a closed-orbit solution at a particular energy. The energy of the injected electron beam is tuned to match the ring by adjusting the RF power in the accelerator structures.


Beam properties and parameters

The X-ray beam parameters of the Lyncean Compact Light Source are as follows and summarized in Table 3.

  • A narrow, quasi-monochromatic spectrum with a few percent relative bandwidth (see Figure 6a), suitable for many applications. For applications requiring smaller bandwidth, a monochromator can be implemented.

  • Energy tunability in the range of 8-42 keV. Development opportunities exist to shift this energy range to either 4-21 keV, or 16-84 keV (see Section 3.2).

  • Partial spatial coherence, advantageous for applications such as propagation- or grating-based phase contrast.

  • Small (4-6 mrad) divergence provides a collimated beam:

    • Using the direct beam with longer propagation distances enables applications requiring a large beam, such as projection- or grating-based imaging

    • Using focusing optics (e.g., Kirkpatrick-Baez type), the beam can be focused down to about 50-100 µm (FWHM) spot size for applications requiring higher flux density, such as diffraction

    • Alternatively, collimating optics can provide a quasi-parallel beam for applications such as SAXS.

  • Approximately round source, advantageous for applications such as imaging (see Figure 6b).

Table 3.

Lyncean Compact Light Source X-ray beam parameters.

ParameterUnitCurrenta)Under developmentb)
Total flux (full bandwidth @35 keV)ph/s~3 × 1010~3 × 1011
Source size (FWHM @35 keV)µm~100~80
Beam divergence (flattop cone)mrad46
Source brightness (full bandwidth @35 keV)ph/s/mrad2/mm2~4 × 1011~4 × 1012
X-ray energy range (tunable)keV15-358-42
X-ray energy bandwidth (AE/E FWHM)%3-53-8
X-ray pulse length (FWHM)ps14090
X-ray repetition rateMHz65 


Measured beam parameters at Munich Compact Light Source20,45


Design parameters of next generation CLS currently under development


Ongoing and future developments

Several developments are currently underway to increase the performance parameters of the next generation Lyncean Compact Light Source (see Table 3). The storage ring will be upgraded to a multi-bend achromat (MBA) design to lower the emittance and increase the current. At the same time, this will allow increasing the electron beam energy to 50 MeV and thereby the X-ray energy to 42 keV. An improved focusing scheme in the optical cavity will reduce the waist of the optical beam. These two improvements combined are expected to increase the brightness by about a factor of 10. Along with an increase in the size of the output aperture of the X-ray beam, which will increase the beam divergence and therefore beam size at the size of the experiment (albeit at broader bandwidth), this will increase the usable X-ray flux by about one order of magnitude as well.

Implementing alternative cavity lasers with 0.5 µm or 2 µm wavelength allows doubling or halving the X-ray energy, shifting the accessible energy range to 16-84 keV or 4-21 keV, respectively. While these are not active developments at the moment, the fundamental technology in terms of suitable drive lasers and optics is available. Longer term development opportunities include further optimization of the

Longer term development opportunities include further optimization of the storage ring lattice and increase in optical cavity power, which provide an avenue to further increase brightness and flux by another order of magnitude in the medium term, and to narrow the bandwidth.



A compact synchrotron source can form the cornerstone of a local or regional X-ray facility. With flexible beam conditioning optics and an interchangeable set of endstations, multiple advanced X-ray applications and techniques can be served (see Figure 7). For example, with a set of focusing optics (Figure 8), focused beam experiments such as diffraction or spectroscopy can be performed. The direct, diverging beam close to the source point can be used for high resolution imaging. With a set of collimating optics, a scattering endstation can be placed at an intermediate distance. Finally, at a far distance (~15 m) and using the direct beam, large field (>50 mm) imaging, such as grating-based multimodal imaging, can be implemented. With a simple system of kinematic mounts, endstations can be moved in and out of the beam quickly and reproducibly.

Figure 7.

Concept of a multi-disciplinary X-ray facility with a Compact Light Source and a beamline with multiple, interchangeable endstations. When using the direct, diverging beam, the distance from the source point defines the beam size. Alternatively, X-ray focusing optics can be inserted into the beam path (for example located in or near the wall of the radiation enclosure) for focused or collimated beam applications.


Figure 8.

X-ray focusing optics developed for the Lyncean Compact Light Source, consisting of two multilayer-coated mirrors in Kirkpatrick-Baez (KB) focusing configuration. They enable focused beam applications such as diffraction or spectroscopy. (a) Photograph of mirror assembly. Inset: Schematic of KB configuration. (b) Calculated reflectivity of the KB mirror pair for 15.3 keV X-ray energy. The center of the curve is tunable from 8 to 20 keV.


Such an X-ray facility brings synchrotron-like beam properties to the local laboratory, spreading out advanced X-ray capabilities regionally, providing increased capacity and broadening access to synchrotron capabilities to local researchers. Local control of experimental time and access allows addressing the need of researchers that have difficulty getting synchrotron beam time. For example, this applies to iterative and longitudinal experiments, experiments requiring many samples for proper statistics, experiments with difficult or restricted samples (e.g., bio- or radiological hazards), or novel techniques still under development. Furthermore, industrial or clinical applications can be developed that are not feasible to become routine under the constraints of synchrotron locations and access models.



A compact synchrotron such as the Lyncean Compact Light Source can serve all major application areas of X-ray research: Diffraction, imaging, spectroscopy and scattering. In the following, we provide an overview of application examples demonstrated using the Lyncean CLS, and opportunities for new applications.


X-ray Diffraction

Initial demonstration experiments on the Lyncean CLS focused on diffraction applications, specifically macromolecular crystallography9 and powder diffraction (unpublished). Opportunities also exist in diffraction for materials science, where the CLS can offer substantially shorter scan times than conventional laboratory systems and enable in situ and some time-resolved experiments. Furthermore, access to higher energies than what is available from the characteristic lines of electron impact sources, along with energy tunability, enables new applications that are not feasible in a lab otherwise.


X-ray Imaging

Given the biomedical imaging research focus of the TUM group, a large number of application examples has been generated in this area.8,1018,2126,2831 While earlier experiments focused on demonstrating different X-ray imaging techniques on the CLS, such as mono-energy X-ray absorption tomography, grating-based multimodal imaging, propagation-based phase contrast and phase contrast tomography, these are now applied to specific biomedical applications and extended to advanced techniques, such as dynamic imaging, K-edge subtraction imaging and others.

There is substantial interest in imaging for materials science using the CLS and extending the resolution to the micron, submicron and nanoscale range. Initial paper studies indicate that imaging speeds can be increased by more than a factor of 10 for micro-CT and nano-CT using the CLS, compared to existing laboratory systems, although some technical developments will be necessary to achieve that. These will be explored in the future.


X-ray Spectroscopy

The energy tunability of the CLS lends itself particularly well to providing X-ray absorption spectroscopy (XAS) capabilities in a laboratory setting. Both X-ray Absorption Near-Edge Structure (XANES) and Extended X-ray Absorption Fine Structure (EXAFS) spectroscopy can be performed with the same setup. With a bandwidth of a few percent, energy-dispersive spectroscopy (ED-XAS) is the most efficient way of implementing this on the CLS. This will also be explored in the future.


Small Angle X-ray Scattering (SAXS)

SAXS for Critical Dimension (CD) measurements on semiconductor samples has been demonstrated in collaboration with NIST (unpublished).



In this paper, we have presented the Lyncean Compact Light Source (CLS), a “mini-synchrotron” X-ray source that bridges the gap between conventional electron-impact sources and synchrotron facilities in terms of X-ray beam characteristics and performance as well as accessibility, cost and infrastructure requirements. It is based on the inverse Compton scattering principle, which in the wave picture can be explained by shrinking the storage ring by a factor of about 100 compared to a typical synchrotron facility, while replacing the permanent magnet undulators with a “laser undulator.” In the particle picture, inverse Compton scattering describes the collision of laser photons with relativistic electrons, in which case the backscattered photons have an energy in the X-ray range. The storage-ring approach of the CLS provides a practical, demonstrated way of achieving high average flux and brightness primarily driven by the high repetition rate.

With such an X-ray source, a multi-disciplinary X-ray facility providing many synchrotron-like capabilities can be set up at a local laboratory. One such facility, the Munich Compact Light Source, has been in operation for several years. The CLS can serve a large range of applications across different X-ray techniques such as diffraction, imaging, spectroscopy and scattering. Future developments can further increase X-ray flux and brightness as well as extend the accessible X-ray energy range.



Röntgen, W. C., “Ueber eine Neue Art von Strahlen,” Sitzungsberichte der Physikalisch-Medizinischen Gesellschaft zu Würzburg, 137 132 –141 (1895). Google Scholar


Skarzynski, T., “Collecting data in the home laboratory: evolution of X-ray sources, detectors and working practices,” Acta Crystallographica Section D Biological Crystallography, 69 (7), 1283 –1288 (2013). Google Scholar


Hemberg, O., Otendal, M. and Hertz, H. M., “Liquid-metal-jet anode electron-impact x-ray source,” Appl. Phys. Lett., 83 (7), 1483 –1485 (2003). Google Scholar


Otendal, M., Tuohimaa, T., Vogt, U. and Hertz, H. M., “A 9 keV electron-impact liquid-gallium-jet x-ray source,” Review of Scientific Instruments, 79 (1), 016102 (2008). Google Scholar


“Sigray Patented x-ray source technologies.”, Sigray, < > (26 July 2019).


“File:Undulator.png - Wikimedia Commons.,” (2018) Google Scholar


Huang, Z. and Ruth, R. D., “Laser-Electron Storage Ring,” Physical Review Letters, 80 (5), 976 –979 (1998). Google Scholar


Bech, M., Bunk, O., David, C., Ruth, R., Rifkin, J., Loewen, R., Feidenhans’l, R. and Pfeiffer, F., “Hard X-ray phase-contrast imaging with the Compact Light Source based on inverse Compton X-rays,” Journal of Synchrotron Radiation, 16 (1), 43 –47 (2009). Google Scholar


Abendroth, J., McCormick, M. S., Edwards, T. E., Staker, B., Loewen, R., Gifford, M., Rifkin, J., Mayer, C., Guo, W., Zhang, Y., Myler, P., Kelley, A., Analau, E., Hewitt, S. N., Napuli, A. J., Kuhn, P., Ruth, R. D. and Stewart, L. J., “X-ray structure determination of the glycine cleavage system protein H of Mycobacterium tuberculosis using an inverse Compton synchrotron X-ray source,” Journal of Structural and Functional Genomics, 11 (1), 91 –100 (2010). Google Scholar


Bech, M., Schleede, S., Potdevin, G., Achterhold, K., Bunk, O., Jensen, T. H., Loewen, R., Ruth, R. and Pfeiffer, F., “Experimental validation of image contrast correlation between ultra-small-angle X-ray scattering and grating-based dark-field imaging using a laser-driven compact X-ray source,” Photonics & Lasers in Medicine, 1 (1), 47 –50 (2012). Google Scholar


Schleede, S., Meinel, F. G., Bech, M., Herzen, J., Achterhold, K., Potdevin, G., Malecki, A., Adam-Neumair, S., Thieme, S. F., Bamberg, F., Nikolaou, K., Bohla, A., Yildirim, A. O., Loewen, R., Gifford, M., Ruth, R., Eickelberg, O., Reiser, M. and Pfeiffer, F., “Emphysema diagnosis using X-ray dark-field imaging at a laser-driven compact synchrotron light source,” Proceedings of the National Academy of Sciences, 109 (44), 17880 –17885 (2012). Google Scholar


Schleede, S., Bech, M., Achterhold, K., Potdevin, G., Gifford, M., Loewen, R., Limborg, C., Ruth, R. and Pfeiffer, F., “Multimodal hard X-ray imaging of a mammography phantom at a compact synchrotron light source,” Journal of Synchrotron Radiation, 19 (4), 525 –529 (2012). Google Scholar


Achterhold, K., Bech, M., Schleede, S., Potdevin, G., Ruth, R., Loewen, R. and Pfeiffer, F., “Monochromatic computed tomography with a compact laser-driven X-ray source,” 1313 (2013). Google Scholar


Meinel, F. G., Schwab, F., Schleede, S., Bech, M., Herzen, J., Achterhold, K., Auweter, S., Bamberg, F., Yildirim, A. Ö., Bohla, A., Eickelberg, O., Loewen, R., Gifford, M., Ruth, R., Reiser, M. F., Pfeiffer, F. and Nikolaou, K., “Diagnosing and Mapping Pulmonary Emphysema on X-Ray Projection Images: Incremental Value of Grating-Based X-Ray Dark-Field Imaging,” PLoS ONE, 8 (3), e59526 2013). Google Scholar


Schwab, F., Schleede, S., Hahn, D., Bech, M., Herzen, J., Auweter, S., Bamberg, F., Achterhold, K., Yildirim, A. Ö., Bohla, A., Eickelberg, O., Loewen, R., Gifford, M., Ruth, R., Reiser, M. F., Nikolaou, K., Pfeiffer, F. and Meinel, F. G., “Comparison of Contrast-to-Noise Ratios of Transmission and Dark-Field Signal in Grating-Based X-ray Imaging for Healthy Murine Lung Tissue,” Zeitschrift für Medizinische Physik, 23 (3), 236 –242 (2013). Google Scholar


Fu, J., Schleede, S., Tan, R., Chen, L., Bech, M., Achterhold, K., Gifford, M., Loewen, R., Ruth, R. and Pfeiffer, F., “An algebraic iterative reconstruction technique for differential X-ray phase-contrast computed tomography,” Zeitschrift für Medizinische Physik, 23 (3), 186 –193 (2013). Google Scholar


Eggl, E., Schleede, S., Bech, M., Achterhold, K., Loewen, R., Ruth, R. D. and Pfeiffer, F., “X-ray phase-contrast tomography with a compact laser-driven synchrotron source,” in Proceedings of the National Academy of Sciences, 5567 –5572 (2015). Google Scholar


Eggl, E., Schleede, S., Bech, M., Achterhold, K., Grandl, S., Sztrókay, A., Hellerhoff, K., Mayr, D., Loewen, R., Ruth, R. D., Reiser, M. F. and Pfeiffer, F., “X-ray phase-contrast tomosynthesis of a human ex vivo breast slice with an inverse Compton x-ray source,” EPL (Europhysics Letters), 116 (6), (2016). Google Scholar


“Munich Compact Light Source (MuCLS).,” MSB: Munich Compact Light Source, (2018) Google Scholar


Eggl, E., Dierolf, M., Achterhold, K., Jud, C., Günther, B., Braig, E., Gleich, B. and Pfeiffer, F., “The Munich Compact Light Source: initial performance measures,” Journal of Synchrotron Radiation, 23 (5), 1137 –1142 (2016). Google Scholar


Eggl, E., Mechlem, K., Braig, E., Kulpe, S., Dierolf, M., Günther, B., Achterhold, K., Herzen, J., Gleich, B., Rummeny, E., Noël, P. B., Pfeiffer, F. and Muenzel, D., “Mono-Energy Coronary Angiography with a Compact Synchrotron Source,” 42211 (2017). Google Scholar


Gradl, R., Dierolf, M., Hehn, L., Günther, B., Yildirim, A. Ö., Gleich, B., Achterhold, K., Pfeiffer, F. and Morgan, K. S., “Propagation-based Phase-Contrast X-ray Imaging at a Compact Light Source,” 4908 (2017). Google Scholar


Töpperwien, M., Gradl, R., Keppeler, D., Vassholz, M., Meyer, A., Hessler, R., Achterhold, K., Gleich, B., Dierolf, M., Pfeiffer, F., Moser, T. and Salditt, T., “Propagation-based phase-contrast x-ray tomography of cochlea using a compact synchrotron source,” 4922 (2018). Google Scholar


Jud, C., Braig, E., Dierolf, M., Eggl, E., Günther, B., Achterhold, K., Gleich, B., Rummeny, E., Noël, P., Pfeiffer, F. and Muenzel, D., “Trabecular bone anisotropy imaging with a compact laser-undulator synchrotron x-ray source,” 14477 (2017). Google Scholar


Gradl, R., Dierolf, M., Günther, B., Hehn, L., Möller, W., Kutschke, D., Yang, L., Donnelley, M., Murrie, R., Erl, A., Stoeger, T., Gleich, B., Achterhold, K., Schmid, O., Pfeiffer, F. and Morgan, K. S., “In vivo Dynamic Phase-Contrast X-ray Imaging using a Compact Light Source,” 6788 (2018). Google Scholar


Gradl, R., Morgan, K. S., Dierolf, M., Jud, C., Hehn, L., Gunther, B., Moller, W., Kutschke, D., Yang, L., Stoeger, T., Pfeiffer, D., Gleich, B., Achterhold, K., Schmid, O. and Pfeiffer, F., “Dynamic in vivo chest x-ray dark-field imaging in mice,” IEEE Transactions on Medical Imaging, 38 (2), 649 –656 (2019). Google Scholar


Burger, K., Ilicic, K., Dierolf, M., Günther, B., Walsh, D. W. M., Schmid, E., Eggl, E., Achterhold, K., Gleich, B., Combs, S. E., Molls, M., Schmid, T. E., Pfeiffer, F. and Wilkens, J. J., “Increased cell survival and cytogenetic integrity by spatial dose redistribution at a compact synchrotron X-ray source,” PLOS ONE, 12 (10), e0186005 2017). Google Scholar


Eggl, E., Grandl, S., Sztrókay-Gaul, A., Dierolf, M., Jud, C., Heck, L., Burger, K., Günther, B., Achterhold, K., Mayr, D., Wilkens, J. J., Auweter, S. D., Gleich, B., Hellerhoff, K., Reiser, M. F., Pfeiffer, F. and Herzen, J., “Dose-compatible grating-based phase-contrast mammography on mastectomy specimens using a compact synchrotron source,” 15700 (2018). Google Scholar


Braig, E., Böhm, J., Dierolf, M., Jud, C., Günther, B., Mechlem, K., Allner, S., Sellerer, T., Achterhold, K., Gleich, B., Noël, P., Pfeiffer, D., Rummeny, E., Herzen, J. and Pfeiffer, F., “Direct quantitative material decomposition employing grating-based X-ray phase-contrast CT,” 16394 (2018). Google Scholar


Kulpe, S., Dierolf, M., Braig, E., Günther, B., Achterhold, K., Gleich, B., Herzen, J., Rummeny, E., Pfeiffer, F. and Pfeiffer, D., “K-edge subtraction imaging for coronary angiography with a compact synchrotron X-ray source,” PLOS ONE e0208446 (2018). Google Scholar


Gradl, R., Dierolf, M., Yang, L., Hehn, L., Günther, B., Möller, W., Kutschke, D., Stoeger, T., Gleich, B., Achterhold, K., Donnelley, M., Pfeiffer, F., Schmid, O. and Morgan, K. S., “Visualizing treatment delivery and deposition in mouse lungs using in vivo x-ray imaging,” Journal of Controlled Release, 307 282 –291 (2019). Google Scholar


Hofmann, A., The Physics of Synchrotron Radiation, digital printed version, Cambridge Univ. Press, Cambridge (2007). Google Scholar


Loewen, R., “A Compact Light Source: Design and Technical Feasibility Study of a Laser-Electron Storage Ring X-Ray Source,” (2004). Google Scholar


Urakawa, J., “Development of a compact X-ray source based on Compton scattering using a 1.3GHz superconducting RF accelerating linac and a new laser storage cavity,” Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment, 637 (1), S47 –S50 (2011). Google Scholar


Hajima, R., Kikuzawa, N., Nishimori, N., Hayakawa, T., Shizuma, T., Kawase, K., Kando, M., Minehara, E., Toyokawa, H. and Ohgaki, H., “Detection of radioactive isotopes by using laser Compton scatteredray beams,” Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment, 608 (1), S57 –S61 (2009). Google Scholar


Graves, W. S., Brown, W., Kaertner, F. X. and Moncton, D. E., “MIT inverse Compton source concept,” Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment, 608 (1), S103 –S105 (2009). Google Scholar


Graves, W. S., Bessuille, J., Brown, P., Carbajo, S., Dolgashev, V., Hong, K.-H., Ihloff, E., Khaykovich, B., Lin, H., Murari, K., Nanni, E. A., Resta, G., Tantawi, S., Zapata, L. E., Kärtner, F. X. and Moncton, D. E., “Compact x-ray source based on burst-mode inverse Compton scattering at 100 kHz,” Phys. Rev. ST Accel. Beams, 17 (12), 120701 (2014). Google Scholar


Graves, W. S. and others., “ASU Compact XFEL,” in Proc. of International Free Electron Laser Conference (FEL’17), 225 –228 (2018). Google Scholar


Stragier, X. F. D., Mutsaers, P. H. A. and Luiten, O. J., “Smart*Light: A Tabletop, High Brilliance, Monochromatic and Tunable Hard X-ray Source for Imaging and Analysis.,” Microscopy and Microanalysis, 24 (S2), 314 –315 (2018). Google Scholar


Variola, A., “The ThomX Project,” in 2nd International Particle Accelerator Conference (IPAC’ 11) WEOAA01, 1903–1905, Joint Accelerator Conferences Website, (2011). Google Scholar


Xu, H. S., Huang, W. H., Tang, C. X. and Lee, S. Y., “Design of a 4.8-m ring for inverse Compton scattering x-ray source,” Phys. Rev. ST Accel. Beams, 17 (7), 070101 (2014). Google Scholar


V. Androsov, N. Ayzatsky, V. Boriskin, E. Bulyak, A. Dovbnya, I. Drebot, P. Gladkikh, A. Gordienko, V. Grevtsev, A. Gvozd, V. Ivashenko, A. Kalamayko, I. Karnaukhov, I. Karnaukhov, V. Kozin, V. Kushnir, V. Lyashchenko, V. Margin, N. Mocheshnikov, et al., “The Kharkov X-Ray Generator Facility NESTOR,” in Proceedings of IPAC2013, 2253 –2255 (2013). Google Scholar


Jacquet, M., “Potential of compact Compton sources in the medical field,” Physica Medica, 32 (12), 1790 –1794 (2016). Google Scholar


Hajima, R., “Status and Perspectives of Compton Sources,” Physics Procedia, 84 35 –39 (2016). Google Scholar


Eggl, E., “Biomedical X-Ray Imaging at the Munich Compact Light Source,” (2017). Google Scholar
© (2019) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
Benjamin Hornberger, Jack Kasahara, Martin Gifford, Ronald Ruth, and Rod Loewen "A compact light source providing high-flux, quasi-monochromatic, tunable X-rays in the laboratory", Proc. SPIE 11110, Advances in Laboratory-based X-Ray Sources, Optics, and Applications VII, 1111003 (9 September 2019);


Seventh-generation CT
Proceedings of SPIE (March 31 2016)
The compact x-ray source ThomX
Proceedings of SPIE (August 23 2017)
User's perspective on x-ray FELs
Proceedings of SPIE (May 15 1997)
The operating modes and the x ray parameters of x...
Proceedings of SPIE (November 10 2004)

Back to Top