29 January 2004 The manufacturing of the XEUS x-ray glass segmented mirrors: status of the investigation and last results
Author Affiliations +
Abstract
The XEUS mission (X-ray Evolving-Universe Spectroscopy Mission) is a future ESA project currently under study. With a mirror collecting area of up to 30 m2 @ 1 keV and 3 m2 @ 8 keV it will outperform the x-ray space observatories like XMM-Newton. In fact it will have a source flux sensitivity and angular resolution respectively 250 times and 7.5 times better if compared to that mission. This huge collecting area is obtained with a 10 m diameter telescope of 50 m focal length. It is foreseen that the whole telescope will be formed by two free flying satellites, one for the mirror assembly and the other for the detectors. The two satellites will be kept aligned by an active tracking/orbit control system. The angular resolution of the optics is set to 5 arcsec with a goal of 2 arcsec. Of course the requirement of high resolution and large diameter of the optics create new technological problems which have to be overcome. First of all the impossibility to create closed Wolter I shells (due to the large diameter) means that the optics will be assembled using rectangular segments of ~1 m x ~0.5 m size. A set of these segments will form a petal. The petals will be assembled to form the whole mirror assembly. Another difficulty arises from the fact that the current design foresees a mass/geometric-area ratio of 0.08 kg/cm2, which is very small and much lower compared with XMM-Newton. Hence the use of materials that can offer both low weight and high stiffness is mandatory. The impossibility to have a thermal control for the huge area of the optics means also that the mirrors have to operate at temperatures between -30 and -40°C. This requirement excludes the epoxy-replication method as option for their manufacturing (CTE mismatch between resin and substrate). Considering all these constrains a possible solution for the realization of the XEUS mirrors has been found that foresees the use of glass or ceramics materials. In this paper we will describe an investigation currently on-going aimed at the development of a procedure to produce large mirror segments from thin Borofloat glass and the preliminary results obtained, that corroborate the viability of the proposed approach. A previous article has introduced the basic ideas and concepts behind this investigation.
© (2004) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
Mauro Ghigo, Mauro Ghigo, Oberto Citterio, Oberto Citterio, Francesco Mazzoleni, Francesco Mazzoleni, Giovanni Pareschi, Giovanni Pareschi, Bernd Aschenbach, Bernd Aschenbach, Heinrich Braeuninger, Heinrich Braeuninger, Peter Friedrich, Peter Friedrich, Guenter Hasinger, Guenter Hasinger, Thorsten Doehring, Thorsten Doehring, Hauke Esemann, Hauke Esemann, Ralf Jedamzik, Ralf Jedamzik, Eva Hoelzel, Eva Hoelzel, Giancarlo Parodi, Giancarlo Parodi, } "The manufacturing of the XEUS x-ray glass segmented mirrors: status of the investigation and last results", Proc. SPIE 5168, Optics for EUV, X-Ray, and Gamma-Ray Astronomy, (29 January 2004); doi: 10.1117/12.506714; https://doi.org/10.1117/12.506714
PROCEEDINGS
16 PAGES


SHARE
RELATED CONTENT

High volume ULE segment production
Proceedings of SPIE (July 21 2016)
SOFIA lightweight primary mirror
Proceedings of SPIE (August 24 1998)
The SiC technology is ready for the next generation of...
Proceedings of SPIE (September 23 2004)
From Herschel to Gaia 3 meter class SiC space...
Proceedings of SPIE (September 26 2011)
Developing SiC for optical system applications
Proceedings of SPIE (October 21 2004)

Back to Top