20 May 2004 EUV source power and lifetime: the most critical issues for EUV lithography
Author Affiliations +
Abstract
Semiconductor chip manufacturers are expecting to use extreme ultraviolet (EUV) lithography for high volume manufacturing of DRAMs and ICs starting by the end of this decade. Among all the technologies and modules which have to be developed EUV sources at 13.5 nm are considered to be the most critical issue. Specifically the required output power of 115 W at the entrance of the illuminator system in combination with the required lifetimes of source components and collector optics make the source technology critical for EUV lithography. The present paper gives an update of the development status of EUV light sources at XTREME technologies, a joint venture of Lambda Physik AG, Goettingen, and Jenoptik LOS GmbH, Jena, Germany. Results on both laser produced plasma (LPP) and gas discharge produced plasma (GDPP), the two major technologies in EUV sources, are given. The LPP EUV sources use xenon-jet target systems and pulsed lasers with 500 W average power at up to 10 kHz developed at XTREME technologies. The maximum conversion efficiency from laser power into EUV in-band power is 1.0 % into 2p solid angle. 2.0 W EUV radiation is generated at 13.5 nm in 2p sr solid angle. The small source volume of < 0.3 mm diameter will allow large collection angles of 5 sr. The intermediate focus power is estimated to 1 W. Collector mirror lifetime tests showed 5 million pulses lifetime without debris mitigation. With debris mitigation in place lifetimes of more than 1 billion pulses are estimated. For the next generation of higher power EUV LPP sources a laser driver has been tested at 1.3 kW average laser power. This will lead to 5 W EUV power in intermediate focus. The GDPP EUV sources use the Z-pinch principle with efficient sliding discharge pre-ionization. Prototype commercial gas discharge sources with an EUV power of 35W in 2p sr were already delivered for integration into EUV microsteppers. These sources are equipped with a debris-filter which results in an optics lifetime exceeding 100 million discharges at 1 kHz repetition frequency. The same lifetime was achieved for the components of the discharge system itself. The progress in the development of high-power discharge sources resulted in an EUV power of 150 W in continuous operation at 4.5 kHz repetition rate by implementation of porous metal cooling technology. The EUV plasma has a FWHM-diameter of 0.5 mm and a FWHM-length of 1.5 mm. The intermediate focus power is calculated to be in the range of 15 W - 20 W, depending somewhat on the transmission of the optical path to the intermediate focus and on the etendue specification. The typical fluctuations of the EUV energy are standard deviation s<5% without any active stabilization. Discharge sources with Sn as emitter were investigated as more efficient alternative to Xenon. Estimates regarding Sn sources reveal the potential of achieving 65 W intermediate focus power by using developed porous metal cooling technology. Improvement of cooling could open the path to 115 W of power for high volume manufacturing using EUV lithography. However, Sn-sources are technologically risky und much less advanced than Xe sources, since fuel-handling and debris mitigation is much more challenging in comparison to Xe-sources. GDPP and LPP sources still compete for the technology of high volume manufacturing sources for EUV lithography. Optimization potential of the etendue of the optical system of EUV scanners will certainly influence any technology decision for HVM sources.
© (2004) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
Uwe Stamm, Uwe Stamm, Juergen Kleinschmidt, Juergen Kleinschmidt, Kai Gaebel, Kai Gaebel, Henry Birner, Henry Birner, Imtiaz Ahmad, Imtiaz Ahmad, Denis Bolshukhin, Denis Bolshukhin, Jesko Brudermann, Jesko Brudermann, Tran Duc Chinh, Tran Duc Chinh, Frank Flohrer, Frank Flohrer, Sven Goetze, Sven Goetze, Guido Hergenhan, Guido Hergenhan, Diethard Kloepfel, Diethard Kloepfel, Vladimir Korobotchko, Vladimir Korobotchko, Bjorn Mader, Bjorn Mader, Rainer Mueller, Rainer Mueller, Jens Ringling, Jens Ringling, Guido Schriever, Guido Schriever, Christian Ziener, Christian Ziener, } "EUV source power and lifetime: the most critical issues for EUV lithography", Proc. SPIE 5374, Emerging Lithographic Technologies VIII, (20 May 2004); doi: 10.1117/12.535410; https://doi.org/10.1117/12.535410
PROCEEDINGS
12 PAGES


SHARE
RELATED CONTENT


Back to Top