Approaching new metrics for wafer flatness: an investigation of the lithographic consequences of wafer non-flatness

John Francis Valley; Noel Poduje; Jaydeep Sinha; Neil Judell; Jie Wu; Marc Boonman; Sjef Tempelaars; Youri van Dommelen; Hans Kattouw; Jan Hauschild; William Hughes; Alexis Grabbe; Les Stanton

doi:10.1117/12.536092

24 May 2004 Approaching new metrics for wafer flatness: an investigation of the lithographic consequences of wafer non-flatness

John Francis Valley, Noel Poduje, Jaydeep Sinha, Neil Judell, Jie Wu, Marc Boonman, Sjef Tempelaars, Youri van Dommelen, Hans Kattouw, Jan Hauschild, William Hughes, Alexis Grabbe, Les Stanton

Author Affiliations +

Proceedings Volume 5375, Metrology, Inspection, and Process Control for Microlithography XVIII; (2004) https://doi.org/10.1117/12.536092
Event: Microlithography 2004, 2004, Santa Clara, California, United States

Abstract

Flatness of the incoming silicon wafer is one major contributor to the ultimate focusing limitation of modern exposure tools. Exposure tools are designed to chuck wafers without creating non-flatness and then use focus control to follow as closely as possible the chucked wafer front surface topography. The smaller size of the exposure slit in a step-and-scan exposure tool, as compared to the previous generation full-field stepper tool, helps minimize the impact of chucked wafer non-flat topography. However, to maintain high throughput and improve critical dimension uniformity (CDU) at sub-wavelength line-widths requires continuous improvement in the incoming silicon wafer flatness. In this paper we report extensive experimental results that review existing wafer flatness metrics and propose the addition of a new metric. The new metric emulates the scanning motion of exposure by integrating the defocus that each point on the wafer experiences during exposure. We show that this method is in better spatial agreement with measured defocus in step-and-scan exposure tools. Simple metrics of moving average (MA) defocus prediction analysis will be defined and shown to correlate very well to post exposure defocus data. These experiments were enabled by the creation of special 300-nm wafers by MEMC. These special wafers include sites with a wide variation in flatness. Prior to exposure the wafers were measured with a high-resolution optical flatness metrology tool (WaferSight by ADE) to obtain industry standard thickness variation (flatness) data. Incoming wafer flatness data is used to predict wafer suitability for lithography at the desired device geometry node (e.g., 90 nm). The flatness data was processed and characterized using both standard metrics (SFQR) and the new MA analysis. The relationship between the industry standard metric (SFQR) and similar metrics applied to MA analysis will be presented. Full two-dimensional maps are used to present spatial correlations and permit simple physical insights into the flatness data sets. Measurements of chucked wafer flatness were made on the same wafers using ASML TWINSCAN in-line metrology. These measurements correlate very well to thickness-based flatness. Un-chucked wafer flatness metrics (SFQR and MA) are shown to correlate well to post exposure defocus data when an appropriate site size is used. This result is discussed in relationship to the industry-accepted practice of specifying un-chucked wafer flatness. Lithography performance tests were made to prove the relevance of the different flatness metrics. The same special wafers are used for lithography performance tests. These tests achieve excellent correlation between post-exposure full-wafer focus control results and predictions based on both SFQ (industry standard) and MA re-mapping of the flatness data. The relationship between measured critical dimension (CD) and defocus is also explored. Point-by-point analysis of CD residual versus measured defocus data nicely follows a Bossung curve. We also show that residual CD values predicted from defocus correlate well with measured values. These experiments confirm the application of industry standard wafer flatness measurements to step-and-scan lithography when appropriately using current metrics. They also present the potential for improved metrics based on the MA defocus prediction analysis to help drive continuous improvement of wafer flatness for advanced step-and-scan lithography.

Citation Download Citation

John Francis Valley, Noel Poduje, Jaydeep Sinha, Neil Judell, Jie Wu, Marc Boonman, Sjef Tempelaars, Youri van Dommelen, Hans Kattouw, Jan Hauschild, William Hughes, Alexis Grabbe, and Les Stanton "Approaching new metrics for wafer flatness: an investigation of the lithographic consequences of wafer non-flatness", Proc. SPIE 5375, Metrology, Inspection, and Process Control for Microlithography XVIII, (24 May 2004); https://doi.org/10.1117/12.536092

ACCESS THE FULL ARTICLE

INSTITUTIONAL
Select your institution to access the SPIE Digital Library.

SELECT YOUR INSTITUTION

PERSONAL
Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.

PERSONAL SIGN IN

No SPIE Account? Create one

PURCHASE THIS CONTENT

SUBSCRIBE TO DIGITAL LIBRARY

50 downloads per 1-year subscription

Members: $195

Non-members: $335 ADD TO CART

25 downloads per 1 - year subscription

Members: $145

Non-members: $250 ADD TO CART

PURCHASE SINGLE ARTICLE

Includes PDF, HTML & Video, when available