Quantification of CD-SEM wafer global charging effect on CD and CD uniformity of 193 nm lithography

Chih-Ming Ke; Hsueh-Liang Hung; Anderson Chang; Jeng-Horng Chen; Tsai-Sheng Gau; Yao-Ching Ku; Burn Jeng Lin; Tadashi Otaka; Kazuhiro Ueda; Hiroki Kawada; Hiroaki Nomura; Nelson Ren

doi:10.1117/12.536147

24 May 2004 Quantification of CD-SEM wafer global charging effect on CD and CD uniformity of 193-nm lithography

Chih-Ming Ke, Hsueh-Liang Hung, Anderson Chang, Jeng-Horng Chen, Tsai-Sheng Gau, Yao-Ching Ku, Burn Jeng Lin, Tadashi Otaka, Kazuhiro Ueda, Hiroki Kawada, Hiroaki Nomura, Nelson Ren

Author Affiliations +

Proceedings Volume 5375, Metrology, Inspection, and Process Control for Microlithography XVIII; (2004) https://doi.org/10.1117/12.536147
Event: Microlithography 2004, 2004, Santa Clara, California, United States

Abstract

For 90 nm technology and below, we need to fight for every nanometer to improve the CD uniformity (CDU). New materials, especially for low-k material, bring about not only complicated integration challenges, but also new metrology difficulties such as SEM image focus failure if using low landing energy (300V) on charging wafer (e.g. -300V). The wafer global charging will also distort the CD SEM magnification and result in CD measurement error. CD SEM venders propose that the distortion be corrected by voltage contrast focus. In order to compare and quantify the measurement error correction with and without using retarding voltage focus, ArF resist non-uniform charging wafers (~ -300V) and low charging wafers (~ -7V) were prepared. Low landing energy like 300V is one of the solutions for ArF resist shrinkage. However, as the low landing energy (300V) meets the high global charging wafer (-300V), SEM cannot get sufficient secondary electron signal to construct image. Therefore, two landing voltages 500eV and 800eV were chosen for the evaluation. Three pitches 1600 nm, 460 nm and 230 nm were investigated. Two indexes are used to evaluate the wafer global charging effect on CD and CDU. One is within-wafer pitch uniformity for determining the CD SEM magnification error. The other is ArF-resist-shrinkage amplitude used to estimate the effective landing energy at charging area. The experimental results show that the pitch uniformity difference with and without using retarding focus can be larger than 2.5 nm. Similar phenomenon is also found for the line width uniformity. Resist shrinkage amplitude is significantly reduced at the highly charged area. Both results show that accurate focus procedure, i.e. retarding voltage focus employing first, is the key to reduce the CD metrology tool measurement error and improve CDU.

Citation Download Citation

Chih-Ming Ke, Hsueh-Liang Hung, Anderson Chang, Jeng-Horng Chen, Tsai-Sheng Gau, Yao-Ching Ku, Burn Jeng Lin, Tadashi Otaka, Kazuhiro Ueda, Hiroki Kawada, Hiroaki Nomura, and Nelson Ren "Quantification of CD-SEM wafer global charging effect on CD and CD uniformity of 193-nm lithography", Proc. SPIE 5375, Metrology, Inspection, and Process Control for Microlithography XVIII, (24 May 2004); https://doi.org/10.1117/12.536147

ACCESS THE FULL ARTICLE

INSTITUTIONAL
Select your institution to access the SPIE Digital Library.

SELECT YOUR INSTITUTION

PERSONAL
Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.

PERSONAL SIGN IN

No SPIE Account? Create one

PURCHASE THIS CONTENT

SUBSCRIBE TO DIGITAL LIBRARY

50 downloads per 1-year subscription

Members: $195

Non-members: $335 ADD TO CART

25 downloads per 1 - year subscription

Members: $145

Non-members: $250 ADD TO CART

PURCHASE SINGLE ARTICLE

Includes PDF, HTML & Video, when available