27 April 2007 Dual beam Nd:YAG laser welding: influence of lubricants to lap joint welding of steel sheets
Author Affiliations +
Proceedings Volume 6346, XVI International Symposium on Gas Flow, Chemical Lasers, and High-Power Lasers; 634617 (2007) https://doi.org/10.1117/12.738673
Event: XVI International Symposium on Gas Flow, Chemical Lasers, and High-Power Lasers, 2006, Gmunden, Austria
Abstract
Laser welding is applied in large-volume production since the late eighties and has revolutionized the possibilities of designing and engineering products. Nevertheless, problems appear during application because the operational conditions in industrial environments fluctuate and can influence the welding process negatively. Contaminations, like lubricants and organic solids, are an example of changing conditions in laser beam welding. If a lap joint is welded, these materials have to be removed from the sheets, otherwise pores and surface failures may appear due to keyhole instabilities induced by uncontrolled outgassing. One possibility for solving this problem is the use of two separate laser beams. For producing these two beams several systems are available for all different kind of lasers. A bifocal optic is such a solution for an Nd:YAG laser. By using this system, the laser beam is divided after collimation with a prism. Afterwards the two beams are focussed with a lens to the surface of the sheet and two single spots are produced. If the distance between the two spots is low, one common, elliptical keyhole is created. With this system two different welding strategies are possible. The spots can be oriented parallel or normal to the feed direction. For stabilizing the laser welding of contaminated steel sheets the parallel arrangement is better, because the amount of contamination is nearly the same as in single spot welding but the total volume of the keyhole is greater and so pressure variations due to uncontrolled evaporation of contaminations are lower. In order to prove this theory and to determine the exact effects some investigations were made at the Chair of Manufacturing Technology of the University of Erlangen-Nuremberg. A 4 kW Nd:YAG laser with a beam parameter product of 25 mm*mrad and a focal distance of 200 mm was used to weld two 1 mm DC04 steel sheets together with a lap joint. Between the sheets a deep drawing lubricant, Castrol FST 6, was used to simulate the contaminations. The sheets were welded with mono- and bifocal optic, whereas with bifocal the power distribution between the two beams was varied. After welding, the seams were qualified by analyzing surface defects and mechanical properties. The results of the investigations show that the adoption of a bifocal optic can increase the stability of the welding process. The distribution between the two single spots has an essential influence on the welding result. In order to get a higher penetration and failure free seams, a 30 % to 70 % distribution between the two spots is better. Furthermore the blade angle has another slight impact on the welding result. For monofocus and bifocus a towing angle between the sheets and the beam produces better welding results. Considering these results it can be resumed that the application of a bifocal optic is a possibility to increase the quality and the stability of lap joint welding but the parameter settings for good results can only be varied in a tight tolerance zone.
© (2007) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
M. Geiger, M. Geiger, M. Merklein, M. Merklein, A. Otto, A. Otto, A. Blankl, A. Blankl, } "Dual beam Nd:YAG laser welding: influence of lubricants to lap joint welding of steel sheets", Proc. SPIE 6346, XVI International Symposium on Gas Flow, Chemical Lasers, and High-Power Lasers, 634617 (27 April 2007); doi: 10.1117/12.738673; https://doi.org/10.1117/12.738673
PROCEEDINGS
6 PAGES


SHARE
RELATED CONTENT

SHADOW a new welding technique: basics and applications
Proceedings of SPIE (October 08 2004)
Market for high-power CO2 lasers
Proceedings of SPIE (March 01 1991)
Lasers in the automobile industry
Proceedings of SPIE (April 08 1996)
Industrial laser marketplace
Proceedings of SPIE (May 01 1990)
Recent developments in laser material processing
Proceedings of SPIE (June 21 2004)
High-power direct-diode laser successes
Proceedings of SPIE (June 01 2004)

Back to Top