This PDF file contains the front matter associated with SPIE Proceedings Volume 8745, including the Title Page, Copyright information, Table of Contents, Invited Panel Discussion, and Conference Committee listing.

The problem of estimating the state of thrusting/ballistic endoatmospheric projectiles moving in 3-dimensional (3-D) space using 2-dimensional (2-D) measurements from a single passive sensor (stationary or moving with constant velocity) is investigated. The estimability is analyzed based on the Fisher Information Matrix (FIM) of the target parameter vector, comprising the initial launch (azimuth and elevation) angles, drag coefficient and thrust, which determine its trajectory according to a nonlinear motion equation. The initial position is assumed to be obtained from the first line of sight (LoS) measurements intersected with a known-altitude plane. The full-rank FIM ensures that this is an estimable system. The corresponding Cram´er-Rao lower bound (CRLB) quantifies the estimation performance of the estimator that is statistically efficient and can be used for impact point prediction (IPP). Due to the inherent nonlinearity of the problem, the maximum likelihood estimate of the target parameter vector is found by using iterated least squares (ILS) numerical approach. A combined grid and ILS approach searches over the launch angles space is proposed. The drag coefficient-thrust grid-based ILS approach is shown to converge to the global maximum and has reliable estimation performance. This is then used for IPP.

Both maximum likelihood estimation as well as minimum mean optimal subpattern assignment (MMOSPA) estimation have been shown to provide meaningful estimates in instances of target identity uncertainty when the number of targets present is known. Maximum likelihood measurement to track association (2D assignment) has been widely studied and is reviewed in this paper. However, it is widely believed that approximate MMOSPA estimation can not be performed in real time except when considering a very small number of targets. This paper demonstrates the MMOSPA estimator arises as a special case of a minimum mean Wasserstein metric estimator when the number of targets is unknown. Additionally, it is shown that approximate MMOSPA estimates can be calculated in microseconds to miliseconds without extensive optimization, making MMOSPA estimation a practicable alternative to more traditional estimators.

Over the years, there have been many proposed methods in set-based tracking. One example of set-based methods is the use of Dempster-Shafer (DS) techniques to support belief-function (BF) tracking. In this paper, we overview the issues and concepts that motivated DS methods for simultaneous tracking and classification/identification. DS methods have some attributes, if applied correctly; but there are some pitfalls that need to be carefully avoided such as the redistribution of the mass associated with conflicting measurements. Such comparisons and applications are found in Dezert-Smarandache Theory (DSmT) methods from which the Proportional Conflict Redistribution (PCR5) rule supports a more comprehensive approach towards applying evidential and BF techniques to target tracking. In the paper, we overview two decades of research in the area of BF tracking and conclude with a comparative analysis of Bayesian, Dempster-Shafer, and the PCR5 methods.

As the number and diversity of sensing assets available for intelligence, surveillance and reconnaissance (ISR) operations continues to expand, the limited ability of human operators to effectively manage, control and exploit the ISR ensemble is exceeded, leading to reduced operational effectiveness. Our approach is to apply the principles of feedback control to ISR operations, “closing the loop” from the sensor collections through automated processing to ISR asset control. Previous work by the authors demonstrated closed-loop control, involving both platform routing and sensor pointing, of a multi-sensor, multi-platform ISR ensemble tasked with providing situational awareness and performing search, track and classification of multiple targets. The multi-asset control used a joint optimization of routes and schedules in a centralized architecture, requiring a fully-connected communications network. This paper presents an extension of the previous work to a decentralized architecture that relaxes the communications requirements. The decentralized approach achieves a solution equivalent to the centralized system when the network allows full communications and gracefully degrades ISR performance as communications links degrade. The decentralized closedloop ISR system has been exercised via a simulation test bed against a scenario in the Afghanistan theater under a variety of network conditions, from full to poor connectivity. Simulation experiment results are presented.

The detection and tracking of surface targets using airborne radars has been extensively investigated in the literature. However, the state-of-the-art techniques in multi-target tracking do not automatically provide information that is potentially of tactical significance, such as anomalous trajectory patterns. In this paper, recent work that attempts to address this problem that is based on stochastic context-free grammars (SCFGs) is reviewed. It is shown that the production rule probabilities in SCFGs can be used to constrain sizes and orientation of target trajectories and hence lead to development of more refined syntactic trackers.

The work considers sensor fusion in a heterogeneous network of proximity and bearings-only sensors for multiple target tracking. Specifically, various particle implementations of the probability hypothesis density filter are proposed that consider two different fusion strategies: 1) the traditional iterated-corrector approach, and 2) explicit fusion of the multitarget density. This work also investigates sensor type (proximity or bearings-only) selection via the Renyi entropy criteria. The simulation results demonstrate comparable localization performances for the two fusion methods, and they show that sensor type selection usually outperforms single sensor type performance.

In an effort to secure the northern and southern United States borders, MITRE has been tasked with developing Modeling and Simulation (M&S) tools that accurately capture the mapping between algorithm-level Measures of Performance (MOP) and system-level Measures of Effectiveness (MOE) for current/future surveillance systems deployed by the the Customs and Border Protection Office of Technology Innovations and Acquisitions (OTIA). This analysis is part of a larger M&S undertaking. The focus is on two MOPs for magnetometer-based Unattended Ground Sensors (UGS). UGS are placed near roads to detect passing vehicles and estimate properties of the vehicle’s trajectory such as bearing and speed. The first MOP considered is the probability of detection. We derive probabilities of detection for a network of sensors over an arbitrary number of observation periods and explore how the probability of detection changes when multiple sensors are employed. The performance of UGS is also evaluated based on the level of variance in the estimation of trajectory parameters. We derive the Cramer-Rao bounds for the variances of the estimated parameters in two cases: when no a priori information is known and when the parameters are assumed to be Gaussian with known variances. Sample results show that UGS perform significantly better in the latter case.

Multitarget tracking in urban environments presents a major theoretical and practical challenge. A recently suggested approach is that of modeling traffic dynamics using the fluid-kinetic methods of traffic-flow theory (TFT). I propose use of the newer, more general, gas-kinetic (GK) approach to TFT. In GK, traffic flow is modeled as a one- or two-dimensional constrained gas. The paper demonstrates the following. (1) The foundational concept in GK--the "phase-space density"--is the same thing as the probability hypothesis density (PHD) of multitarget tracking theory. (2) The theoretically best-that-one-can do approach to TFT-based tracking is a PHD filter. (3) Better performance can be obtained by augmenting this PHD filter as a cardinalized PHD (CPHD) filter. A simple example is presented to illustrate how PHD/CPHD filters can be integrated with conventional macroscopic, mesoscopic, and microscopic TFT.

Detection and tracking of dim targets in heavy clutter environments is a daunting theoretical and practical problem. Application of the recently developed Background Agnostic Cardinalized Probability Hypothesis Density (BA-CPHD) filter provides a very promising approach that adequately addresses all the complexities and the nonlinear nature of this problem. In this paper, we present analysis, derivation, development, and application of a BA-CPHD implementation for tracking dim ballistic targets in environments with a range of unknown clutter rates, unknown clutter distribution, and unknown target probability of detection. The effectiveness and accuracy of the implemented algorithms are assessed and evaluated. Results that evaluate and also demonstrate the specific merits of the proposed approach are presented.

This paper considers the problem of joint multiple target tracking, identification, and classification. Standard approaches tend to treat the tasks of data association, estimation, track management and classification as separate problems. This paper outlines how it is possible to formulate a unified a Bayesian recursion for joint tracking, identification and classification. The formulation is based on the theory of random finite sets or finite set statistics, and specifically labeled random finite sets, which results in a propagation of a multi-target posterior which contains not only target information but all available track information. Implementations are briefly discussed. Where appropriate for particular applications this method can be considered Bayes optimal.

Mahler’s Probability Hypothesis Density (PHD filter), proposed in 2000, addresses the challenges of the multipletarget detection and tracking problem by propagating a mean density of the targets in any region of the state space. However, when retrieving some local evidence on the target presence becomes a critical component of a larger process - e.g. for sensor management purposes - the local target number is insufficient unless some confidence on the estimation of the number of targets can be provided as well. In this paper, we propose a first implementation of a PHD filter that also includes an estimation of localised variance in the target number following each update step; we then illustrate the advantage of the PHD filter + variance on simulated data from a multiple-target scenario.

Single-target tracking filters will typically diverge when their internal measurement or motion models deviate too much from the actual models. Niu, Varshney, Alford, Bubalo, Jones, and Scalzo have proposed a metric-- the normalized innovation squared (NIS)--that recursively estimates the degree of nonlinearity in a single-target tracking problem by detecting filter divergence. This paper establishes the following: (1) NIS can be extended to generalized NIS (GNIS), which addresses more general nonlinearities; (2) NIS and GNIS are actually anomaly detectors, rather than filter-divergence detectors; (3) NIS can be heuristically generalized to a multitarget NIS (MNIS) metric; (4) GNIS also can be rigorously extended to multitarget problems via the multitarget GNIS (MGNIS); (5) explicit, computationally tractable formulas for MGNIS can be derived for use with CPHD and PHD filters; and thus (6) these formulas can be employed as anomaly detectors for use with these filters.

The ensemble Kalman filter relies on a Gaussian approximation being a reasonably accurate representation of the filtering distribution. Reich recently introduced a Gaussian mixture ensemble transform filter which can address scenarios where the prior can be modeled using a Gaussian mixture. Reichs derivation is suitable for a scalar measurement or a vector of uncorrelated measurements. We extend the derivation to the case of vector observations with arbitrary correlations. We illustrate through numerical simulation that implementation is challenging, because the filter is prone to instability.

Situation modeling and threat prediction require higher levels of data fusion in order to provide actionable information. Beyond the sensor data and sources the analyst has access to, the use of out-sourced and re-sourced data is becoming common. Through the years, some common frameworks have emerged for dealing with information fusion—perhaps the most ubiquitous being the JDL Data Fusion Group and their initial 4-level data fusion model. Since these initial developments, numerous models of information fusion have emerged, hoping to better capture the human-centric process of data analyses within a machine-centric framework. 21st Century Systems, Inc. has developed Fusion with Uncertainty Reasoning using Nested Assessment Characterizer Elements (FURNACE) to address challenges of high level information fusion and handle bias, ambiguity, and uncertainty (BAU) for Situation Modeling, Threat Modeling, and Threat Prediction. It combines JDL fusion levels with nested fusion loops and state-of-the-art data reasoning. Initial research has shown that FURNACE is able to reduce BAU and improve the fusion process by allowing high level information fusion (HLIF) to affect lower levels without the double counting of information or other biasing issues. The initial FURNACE project was focused on the underlying algorithms to produce a fusion system able to handle BAU and repurposed data in a cohesive manner. FURNACE supports analyst’s efforts to develop situation models, threat models, and threat predictions to increase situational awareness of the battlespace. FURNACE will not only revolutionize the military intelligence realm, but also benefit the larger homeland defense, law enforcement, and business intelligence markets.

Recognition and understanding of group activities can significantly improve situational awareness in Surveillance Systems. To maximize reliability and effectiveness of Persistent Surveillance Systems, annotations of sequential images gathered from video streams (i.e. imagery and acoustic features) must be fused together to generate semantic messages describing group activities (GA). To facilitate efficient fusion of extracted features from any physical sensors a common structure will suffice to ease integration of processed data into new comprehension. In this paper, we describe a framework for extraction and management of pertinent features/attributes vital for annotation of group activities reliably. A robust technique is proposed for fusion of generated events and entities’ attributes from video streams. A modified Transducer Markup Language (TML) is introduced for semantic annotation of events and entities attributes. By aggregation of multi-attribute TML messages, we have demonstrated that salient group activities can be spatiotemporal can be reliable annotated. This paper discusses our experimental results; our analysis of a set of simulated group activities performed under different contexts and demonstrates the efficiency and effectiveness of the proposed modified TML data structure which facilitates seamless fusion of extracted information from video streams.

In continuous nonlinear filtering theory, we are interested in solving certain parabolic second-order partial dif­ ferential equations (PDEs), such as the Fokker-Planck equation. The fundamental solution of such PDEs can be written in various ways, such as the Feynman-Kac integral and the Feynman path integral (FPI). In addition, the FPI can be defined in several ways. In this paper, the FPI definition based on discretization is reviewed. This has the advantage of being rigorously defined as limits of finite-dimensional integrals. The rigorous and non-rigorous approaches are compared in terms of insight and successes in nonlinear filtering as well as other areas in mathematics.

We derive a new algorithm for particle flow corresponding to Bayes’ rule that was inspired by Knothe- Rosenblatt transport, which is well known in transport theory. We emphasize that our flow is not Knothe- Rosenblatt transport, but rather it is a completely different algorithm for particle flow. In particular, we pick a nearly upper triangular Jacobian matrix, but the meaning of the word “Jacobian” as used here is completely different than used in Knothe-Rosenblatt transport.

We derive several new algorithms for particle flow with non-zero diffusion corresponding to Bayes’ rule. This is unlike all of our previous particle flows, which assumed zero diffusion for the flow corresponding to Bayes’ rule. We emphasize, however, that all of our particle flows have always assumed non-zero diffusion for the dynamical model of the evolution of the state vector in time. Our new algorithm is simple and fast, and it has an especially nice intuitive formula, which is the same as Newton’s method to solve the maximum likelihood estimation (MLE) problem (but for each particle rather than only the MLE), and it is also the same as the extended Kalman filter for the special case of Gaussian densities (but for each particle rather than just the point estimate). All of these new flows apply to arbitrary multimodal densities with smooth nowhere vanishing non-Gaussian densities.

We derive a new algorithm for computing Bayes’ rule using particle flow that has zero curvature. The flow is computed by solving a vector Riccati equation exactly in closed form rather than solving a PDE, with a significant reduction in computational complexity. Our theory is valid for any smooth nowhere vanishing probability densities, including highly multimodal non-Gaussian densities. We show that this new flow is similar to the extended Kalman filter in the special case of nonlinear measurements with Gaussian noise. We also outline more general particle flows, including: constant curvature, geodesic flow, non-constant curvature, piece-wise constant curvature, etc.

We derive five new algorithms to design particle flow for nonlinear filters using the Fourier transform of the PDE that determines the flow of particles corresponding to Bayes’ rule. This exploits the fact that our PDE is linear with constant coefficients. We also use variance reduction and explicit stabilization to enhance robustness of the filter. Our new filter works for arbitrary smooth nowhere vanishing probability densities.

We describe a methodology for modeling the performance of decision-level data fusion between different sensor configurations, implemented as part of the JIEDDO Analytic Decision Engine (JADE). We first discuss a Bayesian network formulation of classical probabilistic data fusion, which allows elementary fusion structures to be stacked and analyzed efficiently. We then present an extension of the Wald sequential test for combining the outputs of the Bayesian network over time. We discuss an algorithm to compute its performance statistics and illustrate the approach on some examples. This variant of the sequential test involves multiple, distinct stages, where the evidence accumulated from each stage is carried over into the next one, and is motivated by a need to keep certain sensors in the network inactive unless triggered by other sensors.

A layered sensing approach helps to mitigate sensor, target, and environmental operating conditions affecting target tracking and recognition performance. Radar sensors provide standoff sensing capabilities over a range of weather conditions; however, operating conditions such as obscuration can hinder radar target tracking. By using other sensing modalities such as electro-optical (EO) building cameras or eye witness reports, continuous target tracking and recognition may be achieved when radar data is unavailable. Information fusion is necessary to associate independent multisource data to ensure accurate target track and identification is maintained. Exploiting the unique information obtained from multiple sensor modalities with non-sensor sources will enhance vehicle track and recognition performance and increase confidence in the reported results by providing confirmation of target tracks when multiple sources have overlapping coverage of the vehicle of interest. The author uses a fusion performance model in conjunction with a tracking and recognition performance model to assess which combination of information sources produce the greatest gains for both urban and rural environments for a typical sized ground vehicle.

The Dempster-Shafer theory is founded on probability theory. The entire machinery of probability theory, and that of measure theory, is at one’s disposal for the understanding and the extension of the Dempster-Shafer theory. It is well known that information theory is also founded on probability theory. Claude Shannon developed, in the 1940’s, the basic concepts of the theory and demonstrated their utility in communications and coding. Shannonian information theory is not, however, the only type of information theory. In the 1960’s and 1970’s, further developments in this field were made by French and Italian mathematicians. They developed information theory axiomatically, and discovered not only the Wiener- Shannon composition law, but also the hyperbolic law and the Inf-law. The objective of this paper is to demonstrate the mathematical connections between the Dempster Shafer theory and the various types of information theory. A simple engineering example will be used to demonstrate the utility of the concepts.

This paper proposes an object detection algorithm and a framework based on a combination of Normalized Central Moment Invariant (NCMI) and Normalized Geometric Radial Moment (NGRM). The developed framework allows detecting objects with offline pre-loaded signatures and/or using the tracker data in order to create an online object signature representation. The framework has been successfully applied to the target detection and has demonstrated its performance on real video and imagery scenes. In order to overcome the implementation constraints of the low-powered hardware, the developed framework uses a combination of image moment functions and utilizes a multi-layer neural network. The developed framework has been shown to be robust to false alarms on non-target objects. In addition, optimization for fast calculation of the image moments descriptors is discussed. This paper presents an overview of the developed framework and demonstrates its performance on real video and imagery scenes.

Effective fusion of multi-parametric heterogeneous data is essential for better object identification, characterization and discrimination. In this report we discuss a practical example of fusing the data provided by imaging and nonimaging electro-optic sensors. The proposed approach allows the processing, integration and interpretation of such data streams from the sensors. Practical examples of improved accuracy in discriminating similar but non-identical objects are presented.

Unattended object detection, recognition and tracking on unmanned reconnaissance platforms in battlefields and urban spaces are topics of emerging importance. In this paper, we present an unattended object recognition system that automatically detects objects of interest in videos and classifies them into various categories (e.g., person, car, truck, etc.). Our system is inspired by recent findings in visual neuroscience on feed-forward object detection and recognition pipeline and mirrors that via two main neuromorphic modules (1) A front-end detection module that combines form and motion based visual attention to search for and detect “integrated” object percepts as is hypothesized to occur in the human visual pathways; (2) A back-end recognition module that processes only the detected object percepts through a neuromorphic object classification algorithm based on multi-scale convolutional neural networks, which can be efficiently implemented in COTS hardware. Our neuromorphic system was evaluated using a variety of urban area video data collected from both stationary and moving platforms. The data are quite challenging as it includes targets at long ranges, occurring under variable conditions of illuminations and occlusion with high clutter. The experimental results of our system showed excellent detection and classification performance. In addition, the proposed bio-inspired approach is good for hardware implementation due to its low complexity and mapping to off-the-shelf conventional hardware.

We present an automated aircraft tracking system as a tool for improving carrier-deck safety. Using a single video stream, aircraft are tracked with relation to the deck, enabling the automatic evaluation of deck safety criteria. System operation involves matching observed image edge features to a calibrated projection of a 3D deck/aircraft model. By identifying the best-fit model, high accuracy 3D tracking is achieved. Testing with a 1:72-scale model indicates a full-scale accuracy on the order of 1 foot spatially and 1 degree in aircraft orientation. Further, our edge-matching based method is insensitive to illumination changes, robust to partial obscuration and highly parallelizable (with preliminary benchmarking indicating real-time feasibility). Automated aircraft tracking allows improved operational locations for launch control personnel and/or provides a second-look deck safety evaluation and, as such, represents a significant new tool for the assurance of carrier deck safety.

This paper is the fifth in a series exploring the possibility of using a synthetic observer to assess the resolution of both real and synthetic (fused) sensors. The previous paper introduced an Automatic Triangle Orientation Detection Algorithm (ATODA) that was capable of recognizing the orientation of an equilateral triangle used as a resolution target, which complemented the Automatic Landolt C Orientation Recognition (ALCOR) software developed earlier. Three different spectral band sensors (infrared, near infrared and visible) were used to collect images that included both resolution targets and militarily relevant targets at multiple distances. The resolution targets were evaluated using the two software algorithms described above. For the current study, subjects viewed the same set of images previously used in order to obtain human-based assessments of the resolutions of these three sensors for comparison with the automated approaches. In addition, the same set of images contained hand-held target objects so that human performance in recognizing the targets could be compared to both the automated and human-based assessment of resolution for each sensor.

With the growing number of image-producing sensors in different spectral bands it is often desirable to provide the operational community with an estimation of the level of target acquisition/recognition performance that could be expected for specific scenarios using these sensors. Many target acquisition/recognition models have been developed over the decades to try and predict expected human performance under various conditions. Many of these are relatively complicated and often concentrate on specific aspects, such as search strategies, atmospherics, or sensor parameters while ignoring other factors. This paper describes the development of a simple, high-level target acquisition/recognition model for predicting human performance for a particular class of operationally relevant, time-based scenarios involving sensor-aided viewing. Assumptions and relevant factors considered in developing the model are discussed and the model, in different forms, is presented. Fundamentally, the model is based on previously-collected human visual performance data using images of the Landolt C acuity target recorded using a short-wave infrared sensor, the Johnny Johnson target recognition criteria, and basic scenario parameters. Limited real-world testing of the model has been accomplished.

Current multispectral night vision (NV) colorization techniques can manipulate images to produce colorized images that closely resemble natural scenes. The colorized NV images can enhance human perception by improving observer object classification and reaction times especially for low light conditions. This paper focuses on the qualitative (subjective) evaluations and comparisons of six NV colorization methods. The multispectral images include visible (Red-Green- Blue), near infrared (NIR), and long wave infrared (LWIR) images. The six colorization methods are channel-based color fusion (CBCF), statistic matching (SM), histogram matching (HM), joint-histogram matching (JHM), statistic matching then joint-histogram matching (SM-JHM), and the lookup table (LUT). Four categries of quality measurements are used for the qualitative evaluations, which are contrast, detail, colorfulness, and overall quality. The score of each measurement is rated from 1 to 3 scale to represent low, average, and high quality, respectively. Specifically, high contrast (of rated score 3) means an adequate level of brightness and contrast. The high detail represents high clarity of detailed contents while maintaining low artifacts. The high colorfulness preserves more natural colors (i.e., closely resembles the daylight image). Overall quality is determined from the NV image compared to the reference image. Nine sets of multispectral NV images were used in our experiments. For each set, the six colorized NV images (produced from NIR and LWIR images) are concurrently presented to users along with the reference color (RGB) image (taken at daytime). A total of 67 subjects passed a screening test (“Ishihara Color Blindness Test”) and were asked to evaluate the 9-set colorized images. The experimental results showed the quality order of colorization methods from the best to the worst: CBCF < SM < SM-JHM < LUT < JHM < HM. It is anticipated that this work will provide a benchmark for NV colorization and for quantitative evaluation using an objective metric such as objective evaluation index (OEI).

Helicopter pilots often have to deal with bad weather conditions and degraded views. Such situations may decrease the pilots' situational awareness significantly. The worst-case scenario would be a complete loss of visual reference during an off-field landing due to brownout or white out. In order to increase the pilots' situational awareness, helicopters nowadays are equipped with different sensors that are used to gather information about the terrain ahead of the helicopter. Synthetic vision systems are used to capture and classify sensor data and to visualize them on multifunctional displays or pilot's head up displays. This requires the input data to be a reliably classified into obstacles and ground. In this paper, we present a regularization-based terrain classifier. Regularization is a popular segmentation method in computer vision and used in active contours. For a real-time application scenario with LIDAR data, we developed an optimization that uses different levels of detail depending on the accuracy of the sensor. After a preprocessing step where points are removed that cannot be ground, the method fits a shape underneath the recorded point cloud. Once this shape is calculated, the points below this shape can be distinguished from elevated objects and are classified as ground. Finally, we demonstrate the quality of our segmentation approach by its application on operational flight recordings. This method builds a part of an entire synthetic vision processing chain, where the classified points are used to support the generation of a real-time synthetic view of the terrain as an assistance tool for the helicopter pilot.

A fusion approach is described that combines texture features from high-resolution panchromatic imagery with land cover statistics derived from co-registered low-resolution global databases to obtain high-resolution land cover maps. The method does not require training data or any human intervention. We use an MxN Gabor filter bank consisting of M=16 oriented bandpass filters (0-180°) at N resolutions (3-24 meters/pixel). The size range of these spatial filters is consistent with the typical scale of manmade objects and patterns of cultural activity in imagery. Clustering reduces the complexity of the data by combining pixels that have similar texture into clusters (regions). Texture classification assigns a vector of class likelihoods to each cluster based on its textural properties. Classification is unsupervised and accomplished using a bank of texture anomaly detectors. Class likelihoods are modulated by land cover statistics derived from lower resolution global data over the scene. Preliminary results from a number of Quickbird scenes show our approach is able to classify general land cover features such as roads, built up area, forests, open areas, and bodies of water over a wide range of scenes.

Very high resolution multispectral imaging reached a high level of reliability and accuracy for target detection and classification. However, in an urban scene, the complexity is raised, making the detection and the identification of small objects difficult. One way to overcome this difficulty is to combine spectral information with 3D data. A set of (very high resolution) airborne multispectral image sequences was acquired over the urban area of Zeebrugge, Belgium. The data consist of three bands in the visible (VIS) region, one band in the near infrared (NIR) range and two bands in the mid-wave infrared (MWIR) region. Images are obtained images at a frame rate of 1/2 frame per second for the VIS and NIR image and 2 frames per second for the MWIR bands. The sensors have a decimetric spatial resolution. The combination of frame rate with flight altitude and speed results in a large overlap between successive images. The current paper proposes a scheme to combine 3D information from along-track stereo, exploiting the overlap between images on one hand and spectral information on the other hand for unsupervised detection of targets. For the extraction of 3D information, the disparity map between different image pairs is determined automatically using an MRF-based method. For the unsupervised target detection, an anomaly detection algorithm is applied. Different methods for inserting the obtained 3D information into the target detection scheme are discussed.

Stand-off 3D THz imaging to detect concealed treats is currently under development. The technology can provide high resolution 3D range data of a passing subject showing layers of clothes and if there are concealed items. However, because it is a scanning sensor technology with a narrow field of view, the subjects pose and position need to be accurately tracked in real time to focus the system and map the imaged THz data to specific body parts. Structured light is a technique to obtain 3D range information. It is, for example, used in the Microsoft Kinect for pose tracking of game players in real time. We demonstrate how structured light can contribute to a THz sensor management system and track subjects in real time. The main advantage of structured light is its simplicity, the disadvantages are the sensitivity to lighting conditions and material properties as well as a relatively low accuracy. Time of flight laser scanning is a technique that complements structured light well, the accuracy is usually much higher and it is less sensitive to lighting conditions. We show that by combining the techniques it is possible to create a robust real time pose tracking system for THz sensor management. We present a concept system based on the Microsoft Kinect and a SICK LMS-511 laser scanner. The laser scanner is used for 2D tracking of the subjects, this tracking is then used to initialize and validate the Microsoft Kinect pose tracking. We have evaluated the sensors individually in both static and dynamic scenes and present their advantages and drawbacks.

Human activity recognition based on human shape dynamics was investigated in this paper. The shape dynamics describe the spatial-temporal shape deformation of a human body during its movement and thus provide important information about the identity of a human subject and the motions performed by the subject. The dynamic shapes of four subjects in five activities (digging, jogging, limping, throwing, and walking) were created via 3-D motion replication. The Paquet Shape Descriptor (PSD) was used to describe subject shapes in each frame. The principal component analysis was performed on the calculated PSDs and principal components (PCs) were used to characterize PSDs. The PSD calculation was then reasonably approximated by its significant projections in the eigen-space formed by PCs and represented by the corresponding projection coefficients. As such, the dynamic human shapes for each activity were described by these projection coefficients, which in turn, along with their derivatives were used to form the feature vectors (attribute sets) for activity classification. Data mining technology was employed with six classification methods used. Seven attribute sets were evaluated with high classification accuracy attained for most of them. The results from this investigation illustrate the great potential of human shape dynamics for activity recognition.

Cadence analysis has been the main focus for discriminating between the seismic signatures of people and animals. However, cadence analysis fails when multiple targets are generating the signatures. We analyze the mechanism of human walking and the signature generated by a human walker, and compare it with the signature generated by a quadruped. We develop Fourier-based analysis to differentiate the human signatures from the animal signatures. We extract a set of basis vectors to represent the human and animal signatures using non-negative matrix factorization, and use them to separate and classify both the targets. Grazing animals such as deer, cows, etc., often produce sporadic signals as they move around from patch to patch of grass and one must characterize them so as to differentiate their signatures from signatures generated by a horse steadily walking along a path. These differences in the signatures are used in developing a robust algorithm to distinguish the signatures of animals from humans. The algorithm is tested on real data collected in a remote area.

Detection of anomalies (outliers or abnormal instances) is an important element in a range of applications such as fault, fraud, suspicious behavior detection and knowledge discovery. In this article we propose a new method for anomaly detection and performed tested its ability to detect anomalous behavior in videos from DARPA's Mind's Eye program, containing a variety of human activities. In this semi-unsupervised task a set of normal instances is provided for training, after which unknown abnormal behavior has to be detected in a test set. The features extracted from the video data have high dimensionality, are sparse and inhomogeneously distributed in the feature space making it a challenging task. Given these characteristics a distance-based method is preferred, but choosing a threshold to classify instances as (ab)normal is non-trivial. Our novel aproach, the Adaptive Outlier Distance (AOD) is able to detect outliers in these conditions based on local distance ratios. The underlying assumption is that the local maximum distance between labeled examples is a good indicator of the variation in that neighborhood, and therefore a local threshold will result in more robust outlier detection. We compare our method to existing state-of-art methods such as the Local Outlier Factor (LOF) and the Local Distance-based Outlier Factor (LDOF). The results of the experiments show that our novel approach improves the quality of the anomaly detection.

Camera surveillance and recognition of deviant behavior is important for the prevention of criminal incidents. A single observation of subtle deviant behavior of an individual may sometimes be insufficient to merit a follow-up action. Therefore, we propose a method that can combine multiple weak observations to make a strong indication that an intervention is required. We analyze the effectiveness of combining multiple observations/tags of different operators, the effects of the tagging instruction these operators received (many tags for weak signals or few tags for strong signals), and the performance of using a semi-automatic system for combining the different observations. The results show that the method can be used to increase hits (detecting criminals) whilst reducing false alarms (bothering innocent passers-by).

This paper will describe a scene invariant method for the unsupervised segmentation of dismounts in depth images. This method can be broken into two parts: ground plane detection and spatial segmentation. The former is accomplished by using RANSAC (RANdom SAmple Consensus) to identify a ground plane in the scene. After performing contrast enhancement the Image is "sliced" into regions. Each classified region is processed by a Robert's edge detector in order to separate each object. Each output is further processed by a block of shape filters that extract the human form.

Handling, manipulation, and placement of objects, hereon called Human-Object Interaction (HOI), in the environment generate sounds. Such sounds are readily identifiable by the human hearing. However, in the presence of background environment noises, recognition of minute HOI sounds is challenging, though vital for improvement of multi-modality sensor data fusion in Persistent Surveillance Systems (PSS). Identification of HOI sound signatures can be used as precursors to detection of pertinent threats that otherwise other sensor modalities may miss to detect. In this paper, we present a robust method for detection and classification of HOI events via clustering of extracted features from training of HOI acoustic sound waves. In this approach, salient sound events are preliminary identified and segmented from background via a sound energy tracking method. Upon this segmentation, frequency spectral pattern of each sound event is modeled and its features are extracted to form a feature vector for training. To reduce dimensionality of training feature space, a Principal Component Analysis (PCA) technique is employed to expedite fast classification of test feature vectors, a kd-tree and Random Forest classifiers are trained for rapid classification of training sound waves. Each classifiers employs different similarity distance matching technique for classification. Performance evaluations of classifiers are compared for classification of a batch of training HOI acoustic signatures. Furthermore, to facilitate semantic annotation of acoustic sound events, a scheme based on Transducer Mockup Language (TML) is proposed. The results demonstrate the proposed approach is both reliable and effective, and can be extended to future PSS applications.

An algorithm is proposed for nonlinear and non-stationary processes concerning ATR. The general approach is to decompose a complex task into multiple domains in space and time based on predictability of the object modification dynamics. The model is composed of multiple modules, each of which consists of a state prediction model and correctional multivariate system. Prediction error function is used to weigh the outputs of multiple hierarchical levels.

Robust vehicle detection and identification is required for the intelligent persistent surveillance systems. In this paper, we present a Multi-attribute Vehicle Detection and Identification technique (MVDI) for detection and classification of stationary vehicles. The proposed model uses a supervised Hamming Neural Network (HNN) for taxonomy of shape of the vehicle. Vehicles silhouette features are employed for the training of the HNN from a large array of training vehicle samples in different type, scale, and color variation. Invariant vehicle silhouette attributes are used as features for training of the HNN which is based on an internal Hamming Distance and shape features to determine degree of similarity of a test vehicle against those it’s selectively trained with. Upon detection of class of the vehicle, the other vehicle attributes such as: color and orientation are determined. For vehicle color detection, provincial regions of the vehicle body are used for matching color of the vehicle. For the vehicle orientation detection, the key structural features of the vehicle are extracted and subjected to classification based on color tune, geometrical shape, and tire region detection. The experimental results show the technique is promising and has robustness for detection and identification of vehicle based on their multi-attribute features. Furthermore this paper demonstrates the importance of the vehicle attributes detection towards the identification of Human-Vehicle Interaction events.

We present a new cross-spectral variation of the Cross-Ambiguity Function (CAF) and demonstrate use of the CS-CAF in obtaining improved Frequency Difference of Arrival (FDOA) estimates. Unlike the conventional CAF process that estimates the FDOA of two signals received by moving receivers, as approximately constant over a short observation time, the CS-CAF models FDOA as a slowly varying continuous function. Under the CS-CAF model, we apply cross-spectral estimation methods to estimate and track the instantaneous FDOA of the received signals. This has two important advantages. The cross-spectral frequency estimation methods are extremely accurate, and by modeling the FDOA as a continuous function of time, we resolve the issue of assigning an event time to the estimated FDOA. In addition, by recovering an FDOA component from the received signals, we may apply LaGrange interpolation to track the instantaneous phase of the FDOA component, enabling an even more accurate estimate of instantaneous FDOA.

The number of elements in a nonplanar antenna array, their respective farfield radiation patterns, the relative spacing between the elements, and the signal processing approach determine the angle-of-arrival (AOA) estimation performance for a direction finding (DF) system. Designing an airborne DF system becomes challenging as the wavelengths of the signals of interest become large with respect to the host aircraft. Given an ensemble of structurally integrated (SI) antennas designed using a discrete number of feed points, this paper presents an analysis of AOA estimation as a function of the number of SI feed elements and their respective locations on a large, three-dimensional aircraft model at HF (2-32 MHz). Empirical results for AOA estimation errors versus the number and physical location of feed points are presented using the maximum likelihood method estimator for 4 and 11 MHz signals of interest.

During the SPIE 2012 conference, panelists convened to discuss “Real world issues and challenges in Human Social/Cultural/Behavioral modeling with Applications to Information Fusion.” Each panelist presented their current trends and issues. The panel had agreement on advanced situation modeling, working with users for situation awareness and sense-making, and HSCB context modeling in focusing research activities. Each panelist added different perspectives based on the domain of interest such as physical, cyber, and social attacks from which estimates and projections can be forecasted. Also, additional techniques were addressed such as interest graphs, network modeling, and variable length Markov Models. This paper summarizes the panelists discussions to highlight the common themes and the related contrasting approaches to the domains in which HSCB applies to information fusion applications.

With the emergence of long lasting surveillance systems, e.g., full motion video (FMV) networks and wide area motion imagery (WAMI) sensors, extracting targets’ long term pattern of life over a day becomes possible. In this paper, we present a framework for extracting the pattern of life (POL) of targets from WAMI video. We first apply a context-aware multi-target tracker (CAMT) to track multiple targets in the WAMI video and obtain the targets’ tracklets, traces, and the locations, from surveillance information extracted from the targets' long-term trajectories. Then, entity networks propagate over time are constructed with targets’ tracklets, traces, and the interested locations. Finally, the entity network is analyzed using network retrieving technique to extract the POL of interested targets.

In this paper, we present our enhanced model of multi-entity activity recognition, which operates on person and vehicle tracks, converts them into motion and interaction events, and represents activities via multiattributed role networks encoding spatial, temporal, contextual, and semantic characteristics of coordinated activities. Our model is flexible enough to capture variations of behaviors, and is used for both learning of repetitive activity patterns in semi-supervised manner, and detection of activities in data with large ambiguity and high ratio of irrelevant to relevant tracks and events. We demonstrate our models using activities captured in CLIF persistent wide area motion data collections.

This paper explores the current practices in social data fusion and analysis as it applies to consumer-oriented applications in a slew of areas including business, economics, politics, sciences, medicine, education and more. A categorization of these systems is proposed and contributions to each area are explored preceded by a discussion of some special issues related to social data and networks. From this work, future paths of consumer-based social data analysis research and current outstanding problems are discovered.

Predictive analytics in situation awareness requires an element to comprehend and anticipate potential adversary activities that might occur in the future. Most work in high level fusion or predictive analytics utilizes machine learning, pattern mining, Bayesian inference, and decision tree techniques to predict future actions or states. The emergence of social computing in broader contexts has drawn interests in bringing the hypotheses and techniques from social theory to algorithmic and computational settings for predictive analytics. This paper aims at answering the question on how influence and attitude (some interpreted such as intent) of adversarial actors can be formulated and computed algorithmically, as a higher level fusion process to provide predictions of future actions. The challenges in this interdisciplinary endeavor include drawing existing understanding of influence and attitude in both social science and computing fields, as well as the mathematical and computational formulation for the specific context of situation to be analyzed. The study of ‘influence’ has resurfaced in recent years due to the emergence of social networks in the virtualized cyber world. Theoretical analysis and techniques developed in this area are discussed in this paper in the context of predictive analysis. Meanwhile, the notion of intent, or ‘attitude’ using social theory terminologies, is a relatively uncharted area in the computing field. Note that a key objective of predictive analytics is to identify impending/planned attacks so their ‘impact’ and ‘threat’ can be prevented. In this spirit, indirect and direct observables are drawn and derived to infer the influence network and attitude to predict future threats. This work proposes an integrated framework that jointly assesses adversarial actors’ influence network and their attitudes as a function of past actions and action outcomes. A preliminary set of algorithms are developed and tested using the Global Terrorism Database (GTD). Our results reveals the benefits to perform joint predictive analytics with both attitude and influence. At the same time, we discover significant challenges in deriving influence and attitude from indirect observables for diverse adversarial behavior. These observations warrant further investigation of optimal use of influence and attitude for predictive analytics, as well as the potential inclusion of other environmental or capability elements for the actors.

Accurate and fast detection of infrared (IR) dim target has very important meaning for infrared precise guidance, early warning, video surveillance, etc. In this paper, some basic principles and the implementing flow charts of a series of algorithms for target detection are described. These algorithms are traditional two-frame difference method, improved three-frame difference method, background estimate and frame difference fusion method, and building background with neighborhood mean method. On the foundation of above works, an infrared target detection software platform which is developed by OpenCV and MFC is introduced. Three kinds of tracking algorithms are integrated in this software. In order to explain the software clearly, the framework and the function are described in this paper. At last, the experiments are performed for some real-life IR images. The whole algorithm implementing processes and results are analyzed, and those algorithms for detection targets are evaluated from the two aspects of subjective and objective. The results prove that the proposed method has satisfying detection effectiveness and robustness. Meanwhile, it has high detection efficiency and can be used for real-time detection.

This paper introduces a method by which one can find the optimum iteration numbers for noise removal and deconvolution of sampled data. The method employs the mean squared error, which is the square of the difference between the deconvolution result and the input, for optimization. As an example of the iterative methods of noise removal and deconvolution, the always convergent method of Ioup is used for the simultaneous optimization by simulation research presented in this paper. This method is applied to achieve optimization for two Gaussian impulse response functions, one narrow (rapidly converging) and the other wide (slowly converging). The input function used consists of three narrow peaks selected to give some overlap after convolution with the Gaussian impulse response function. Normal distributed noise is added to the convolution of the input with the impulse response function. A range of signal-to-noise ratio is used to optimize the always convergent iterations for both of these Gaussians. For the narrow Gaussian 15 signal-to-noise ratio cases are studied while for the wide Gaussian 11 signal-to-noise ratios cases are considered. To achieve statistically reliable results 50 noisy data sets are generated for each signal-to-noise ratio case. For a given signal-to-noise ratio case the optimum deconvolution and noise removal iteration numbers are found and tabulated. The tabulated results are given in tables one through three. Once these optimum numbers are found they can be used in an equivalent window in the Fourier transform domain, although the non-negativity constraint can only be applied in the function domain.

This paper introduces a method by which one can find the optimum iteration numbers for noise removal and deconvolution of sampled data. The method employs the mean squared error, which is the pointwise square of the difference between the deconvolution result and the input, for optimization. The always convergent iterative deconvolution and noise removal methods of Ioup are used for the simultaneous optimization by simulation research presented in this paper. This method is applied to achieve optimization for a seismic wavelet impulse response function. The optimized always convergent results are compared to those of least square inverse filtering and the reblurring procedure of Kawata and Ichioka. The input data used is a spike train of various separations to give a calibrated measure of resolution. A range of signal-to-noise ratios (SNR’s) is used in the optimization procedure. No noise removal is applied prior to unfolding for the reblurring procedure and the least squares inverse filtering methods. To achieve statistically reliable results 50 noisy data sets are generated for each SNR case for the always convergent method and 10 noisy cases for the reblurring procedure and the least squares inverse filtering techniques. For a given SNR case the average mean squared error, the average optimum deconvolution, and the average noise removal iteration numbers are found and tabulated. The tabulated results are plotted versus the average SNR. Once these optimum numbers are found they can be used in an equivalent window in the Fourier transform domain.

In order to improve the accuracy and efficiency of weld defect segmentation in automatic radiographic nondestructive testing and evaluation（NDT&E）, an effective weld defect segmentation algorithm based on flooding has been developed, which has the self-adaptive characteristics. Firstly, the defect’s feature points are extracted from the scale space of radiographic films. Based on the information of defect points, the seed points and seed domains of defect discrimination are adaptively determined, in which the defect segmentation seed will be searched. Then, aiming at the sparsity of weld defects and canyon characteristics of 3D topographic map of defect regions, the drip-watering and water flooding have been used for reference. The flooding is carried out by using line-flooding algorithm, in which water starts from defect seed points and flows to the neighbor regions in order. On the basis of the flooding-area change and flooding-level ascending velocity, the defect segmentation threshold values are determined and the weld defects also are segmented from the radiographic films. At last, the comparative experiments have been carried out to compare the proposed algorithm with the watershed segmentation algorithm and background subtraction segmentation algorithm. And the experiment results confirm that the proposed algorithm obviously improves the accuracy and efficiency of weld defect’s segmentation.