This PDF file contains the front matter associated with SPIE Proceedings Volume 9536, including the Title Page, Copyright information, Table of Contents, Introduction (if any), and Conference Committee listing.

A fast all fiber based setup for stimulated Raman microscopy based on a rapidly wavelength swept cw-laser is presented. The applied Fourier domain mode locked (FDML) laser is a fiber ring laser, providing a continuously changing wavelength output over time. This fast swept source allows us to rapidly change the wavelength and, thereby the energy difference with respect to a single color pump laser. The pump laser is a master oscillator power amplifier based on a fiber amplified laser diode and a Raman shifter. By controlled variation of the relative timing between probe and pump laser with an arbitrary waveform generator, the Raman signals are encoded in time and they are directly acquired with a synchronized, fast analog-to-digital converter. This setup is capable of acquiring rapidly high resolution spectra (up to 0.5 cm^-1) with shot noise limited sensitivity over a broadband (750 cm^-1 to 3150 cm^-1) spectral region. Here, we show the performance of this system for imaging in the CH-stretch region around 3000 cm^-1 and in the fingerprint region around 1600 cm^-1. We present hyperspectral images of a plant stem slice with molecular contrast of lignin and a lipid representative as well as images of PS (polystyrene) and PMMA (poly(methyl methacrylate) beads with an acquisition speed of 18 μs per spectral point.

We map out the group delays of all the 169 single-mode cores of a 30 cm long multi-core fiber using phaseshifting spectral interferometry. We then present and apply a new experimental concept suitable for partially compensating the measured inter-core group delay dispersion. The compensation scheme is based on two wave front shapers in a 4-f geometry and group delays are imposed in the Fourier plane between them. These results are of relevance for cases where one desires to perform imaging through optical fibers using femtosecond excitation as is the case in the two-photon lensless endoscopes which have recently been demonstrated.

Ionising radiation causes various types of DNA damages including double strand breaks (DSBs). DSBs are often recognized by DNA repair protein ATM which forms gamma-H2AX foci at the site of the DSBs that can be visualized using immunohistochemistry. However most of such experiments are of low throughput in terms of imaging and image analysis techniques. Most of the studies still use manual counting or classification. Hence they are limited to counting a low number of foci per cell (5 foci per nucleus) as the quantification process is extremely labour intensive. Therefore we have developed a high throughput instrumentation and computational pipeline specialized for gamma-H2AX foci quantification. A population of cells with highly clustered foci inside nuclei were imaged, in 3D with submicron resolution, using an in-house developed high throughput image cytometer. Imaging speeds as high as 800 cells/second in 3D were achieved by using HiLo wide-field depth resolved imaging and a remote z-scanning technique. Then the number of foci per cell nucleus were quantified using a 3D extended maxima transform based algorithm. Our results suggests that while most of the other 2D imaging and manual quantification studies can count only up to about 5 foci per nucleus our method is capable of counting more than 100. Moreover we show that 3D analysis is significantly superior compared to the 2D techniques.

Super-resolution techniques for breaking the diffraction barrier are spread out over multiple studies nowadays. Single-molecule localization microscopy such as PALM, STORM, GSDIM, etc allow to get super-resolved images of cell ultrastructure by precise localization of individual fluorescent molecules via their temporal isolation. However, these methods are supposed the use of fluorescent dyes and proteins with special characteristics (photoactivation/photoconversion). At the same time, there is a need for retaining high photostability of fluorophores during long-term acquisition. Here, we first showed the potential of common red fluorescent protein for single-molecule localization microscopy based on spontaneous intrinsic blinking. Also, we assessed the effect of different imaging media on photobleaching of these fluorescent proteins. Monomeric orange and red fluorescent proteins were examined for stochastic switching from a dark state to a bright fluorescent state. We studied fusions with cytoskeletal proteins in NIH/3T3 and HeLa cells. Imaging was performed on the Nikon N-STORM system equipped with EMCCD camera. To define the optimal imaging conditions we tested several types of cell culture media and buffers. As a result, high-resolution images of cytoskeleton structure were obtained. Essentially, low-intensity light was sufficient to initiate the switching of tested red fluorescent protein reducing phototoxicity and provide long-term live-cell imaging.

In cardiac imaging, the spacing between sub-cellular sarcomere structures is of great importance to physiologists in understanding muscle design and performance. Making accurate measurements of the sarcomere length (SL) presents a significant imaging challenge owing to the size of the SL (~2μm) and its naturally low variability (<6%), requiring a high level of precision to determine subtle changes between heart disease models. Moreover, measurements of SL from traditional two-photon imaging have so far been ambiguous to within a factor of cos(α), where α is the inclination of the tissue with respect to the focal plane. By remotely focussing a customised two-photon microscope, it is possible to image heart cells at two oblique angles within 200ms. The oblique images uniquely resolve the tissue inclination ambiguity and reduce the variance of SL measures by as much as 23%. This improved precision is crucial in discerning between pathological models of chronic hypertension. As well as improving measurement precision, the distribution of α across the field of view provides additional structural information which can be related to disease morphology. To validate this new imaging protocol, the value of α calculated from the oblique planes provided the input to a rigid model cell which was used to predict the appearance of the cell in the conventional focal plane. The comparison of the model to the image data provided a confidence metric for our measurements. Finally, by considering the optical transfer function, the range of cell orientations for which the method is valid could be calculated.

In this work we have developed a single-pixel optical microscope that provides both re ection and transmission images of the sample under test by attaching a diamond pixel layout DMD to a commercial inverted microscope. Our system performs simultaneous measurements of re ection and transmission modes. Besides, in contrast with a conventional system, in our single-element detection system both images belong, unequivocally, to the same plane of the sample. Furthermore, we have designed an algorithm to modify the shape of the projected patterns that improves the resolution and prevents the artifacts produced by the diamond pixel architecture.

Ultramicroscopy-UM allows 3D-vizualization of biological specimens with μm-resolution. The spatial intensity distribution and thickness of the light sheet have the foremost impact on the quality of image in UM. In this paper, we present different designs for generating light sheet.

The optical unit in standard UM as well as two optimized designs for generating light sheet are reviewed and discussed. The optical characteristics of their light sheet, length and diameter of the line of focus and spatial intensity distribution along the light sheet, are compared. The experimental results demonstrate a marked improvement in reconstructions of representative biological specimens in the third design utilizing aspheric elements. Furthermore, we present our latest achievements in the clearing process of the specimens as well as detection signals by microscope’s objectives that improve further the image quality.

Development of devices for automatic identification of diseases is desired especially in developing countries. In the case of malaria, even today the gold standard is the inspection of chemically treated blood smears through a microscope. This requires a trained technician/microscopist to identify the cells in the field of view, with which the labeling chemicals gets attached. Bright field microscopes provide only low contrast 2D images of red blood cells and cell thickness distribution cannot be obtained. Quantitative phase contrast microscopes can provide both intensity and phase profiles of the cells under study. The phase information can be used to determine thickness profile of the cell. Since cell morphology is available, many parameters pertaining to the 3D shape of the cell can be computed. These parameters in turn could be used to decide about the state of health of the cell leading to disease diagnosis. Here the investigations done on digital holographic microscope, which provides quantitative phase images, for comparison of parameters obtained from the 3D shape profile of objects leading to identification of diseased samples is described.

The lateral shearing phase shifting interference microscopy with low coherent illumination for tomography of living cells has been proposed. To create projections of a sample at different angles the angular scanning of the probe beam was used. The experimental results of erythrocyte tomogram reconstruction are presented.

We review our technique for tomographic phase microscopy with optical tweezers [1]. This tomographic phase microscopy approach enables full 3-D refractive-index reconstruction. Tomographic phase microscopy measures quantitatively the 3- D distribution of refractive-index in biological cells. We integrated our external interferometric module with holographic optical tweezers for obtaining quantitative phase maps of biological samples from a wide range of angles. The close-tocommon- path, off-axis interferometric system enables a full-rotation tomographic acquisition of a single cell using holographic optical tweezers for trapping and manipulating with a desired array of traps, while acquiring phase information of a single cell from all different angles and maintaining the native surrounding medium. We experimentally demonstrated two reconstruction algorithms: the filtered back-projection method and the Fourier diffraction method for 3-D refractive index imaging of yeast cells.

In order to extend the analysis of the datasets produced by lensfree video microscopy we have implemented a cell tracking algorithm to combine and correlate cell motility to the previously devised metrics to quantify e.g. cell adhesion and spreading, cell division, and cell death. In this paper we present the assessment of these new methodology on experiments involving three different cell lines, namely 3T3 fibroblast cells, primary HUVEC cells and macrophage THP1 cells. We demonstrate that the good spatial resolution and the fast frame rate obtained with of our lensfree video microscope allows standard cell tracking algorithm to be computed. The results is the possibility to analyze thousands of cells successfully tracked over tens of hours. The results is the possibility to compare different cell cultures in terms of e.g. cell motility and cell confinement ration. Ultimately we managed to measure the doubling time at single cell level over a large number of N=235 cells tracked over two days.

We developed a new imaging tool that can help pathologists in recording wide-field images of tissue slides. We present a simple cost-effective lens-free imaging method to record 2-4μm resolution wide-field (10 mm² - 6 cm²) images of stained and unstained tissue slides. To our knowledge, our method is the first technique that enables fast (less than 5 minutes) wide-field lens-free imaging of such dense samples. Multiple holograms are recorded with different wavelength illumination, and a multispectral algorithm is used to retrieve both amplitude and phase. Our method can be used to retrieve images of stained tissue slides. For such absorbing object, the useful information is included in the modulus of the reconstructed complex field. Our method can also be applied to retrieve images of unstained tissue slides, where the useful information is in the retrieved phase. This technique is much cheaper and compact than a conventional microscope and could be made portable. Moreover, it enables wide field unstained tissue slides imaging, which could quickly provide useful information, for example on frozen section biopsies, when a rapid diagnosis is needed during surgery.

Introduction: In breast cancer (BC), desmoplastic reaction, assembled primarily by fibroblasts, is associated with unfavorable prognosis, but the reason of this fact remains still unclear. In this context, nonlinear optics microscopy, including Fluorescence Lifetime Imaging Microscopy (FLIM), has provided advancement in cellular metabolism research. In this paper, our purpose is to differentiate BC cells metabolism with or without contact to desmoplastic reaction. Formalin fixed, paraffin embedded samples were used at different points of hematoxylin stained sections. Methodology: Sections from 14 patients with invasive ductal breast carcinoma were analyzed with FLIM methodology to NAD(P)H and FAD fluorescence lifetime on a Confocal Upright LSM780 NLO device (Carl Zeiss AG, Germany). Quantification of the fluorescence lifetime and fluorescence intensity was evaluated by SPC Image software (Becker &Hickl) and ImageJ (NIH), respectively. Optical redox ratio was calculated by dividing the FAD fluorescence intensity by NAD(P)H fluorescence intensity. Data value for FLIM measurements and fluorescence intensities were calculated using Wilcoxon test; p< 0.05 was considered significant. Results: BC cells in contact with desmoplastic reaction presented a significantly lower NAD(P)H and FAD fluorescence lifetime. Furthermore, optical redox ratio was also lower in these tumor cells. Conclusion: Our results suggest that contact of BC cells with desmoplastic reaction increase their metabolic activity, which might explain the adverse prognosis of cases associated with higher peritumoral desmoplastic reaction.

A newly developed hardware-friendly non-iterative fluorescence lifetime imaging (FLIM) analysis method was verified in an FPGA chip. Its performances were also demonstrated on two-photon FLIM images of gold nanorods (GNRs)-Cy5 labelled Hela cells. The results obtained by the proposed method can be presented in a polor plot to be compared to the widely used phasor (Phasor) approach. Combining our method with Phasor will be very useful in FLIM analysis.

Atherosclerosis is among the most widespread cardiovascular diseases and one of the leading cause of death in the Western World. Characterization of arterial tissue in atherosclerotic condition is extremely interesting from the diagnostic point of view, especially for what is concerning collagen content and organization because collagen plays a crucial role in plaque vulnerability. Routinely used diagnostic methods, such as histopathological examination, are limited to morphological analysis of the examined tissues, whereas an exhaustive characterization requires immunehistochemical examination and a morpho-functional approach. Non-linear microscopy techniques offer the potential for providing morpho-functional information on the examined tissues in a label-free way. In this study, we employed combined SHG and FLIM microscopy for characterizing collagen organization in both normal arterial wall and within atherosclerotic plaques. Image pattern analysis of SHG images allowed characterizing collagen organization in different tissue regions. In addition, the analysis of collagen fluorescence decay contributed to the characterization of the samples based on collagen fluorescence lifetime. Different values of collagen fiber mean size, collagen distribution, and collagen anisotropy and collagen fluorescence lifetime were found in normal arterial wall and within plaque depositions, prospectively allowing for automated classification of atherosclerotic lesions and plaque vulnerability. The presented method represents a promising diagnostic tool for evaluating atherosclerotic tissue and has the potential to find a stable place in clinical setting as well as to be applied in vivo in the near future.

Quantitative confocal fluorescence microscopy imaging without scanning is developed for the study of fast dynamical processes. The method relies on the use of massively parallel Fluorescence Correlation Spectroscopy (mpFCS). Simultaneous excitation of fluorescent molecules across the specimen is achieved by passing a single laser beam through a Diffractive Optical Element (DOE) to generate a quadratic illumination matrix of 32×32 light sources. Fluorescence from 1024 illuminated spots is detected in a confocal arrangement by a matching matrix detector consisting of the same number of single-photon avalanche photodiodes (SPADs). Software was developed for data acquisition and fast autoand cross-correlation analysis by parallel signal processing using a Graphic Processing Unit (GPU). Instrumental performance was assessed using a conventional single-beam FCS instrument as a reference. Versatility of the approach for application in biomedical research was evaluated using ex vivo salivary glands from Drosophila third instar larvae expressing a fluorescently-tagged transcription factor Sex Combs Reduced (Scr) and live PC12 cells stably expressing the fluorescently tagged mu-opioid receptor (MOP_eGFP). We show that quantitative mapping of local concentration and mobility of transcription factor molecules across the specimen can be achieved using this approach, which paves the way for future quantitative characterization of dynamical reaction-diffusion landscapes across live cells/tissue with a submillisecond temporal resolution (presently 21 μs/frame) and single-molecule sensitivity.

Diffuse optical tomography (DOT) is a growing area of research in the field of biomedical optics and neurosciences. Over the past 20 years, technical development allowed a more and more accurate detection of the brain activation, both spatially and in the calculation of the variations of chromophores’s concentrations such as Hemoglobin, cytochrome c oxidase, etc. In particular, time resolved systems are able to distinguish between superficial layers (skin, skull) and deep layers (brain) allowing the differentiation between the systemic response and the response of the brain. In order to increase the accuracy of the brain’s activation detection, we have developed a Hyperspectral Time Resolved DOT system. It is composed of a compact supercontinuum laser within the picosecond range for the source part and of an ICCD camera coupled with an imaging spectrometer for the detection part. This allows a simultaneous detection of the spatial and spectral dimension, as well as the time of flight of photons. Through the information acquired by our system, we’ve been able to retrieve, to our knowledge, the first spectrum of the physiology of the human brain activity as function as depth. Here we present the instrument and show our first in-vivo results that are demonstrating its capabilities to distinguish between the skin’s response and the brain’s responses during a cognitive task. We are also focused on the detection of the Fast Optical Signal.

Large volumes imaging with microscopic resolution is limited by light scattering. In the last few years based on refractive index matching, different clearing approaches have been developed. Organic solvents and water-based optical clearing agents have been used for optical clearing of entire mouse brain. Although these methods guarantee high transparency and preservation of the fluorescence, though present other non-negligible limitations. Tissue transformation by CLARITY allows high transparency, whole brain immunolabelling and structural and molecular preservation. This method however requires a highly expensive refractive index matching solution limiting practical applicability. In this work we investigate the effectiveness of a water-soluble clearing agent, the 2,2'-thiodiethanol (TDE) to clear mouse and human brain. TDE does not quench the fluorescence signal, is compatible with immunostaining and does not introduce any deformation at sub-cellular level. The not viscous nature of the TDE make it a suitable agent to perform brain slicing during serial two-photon (STP) tomography. In fact, by improving penetration depth it reduces tissue slicing, decreasing the acquisition time and cutting artefacts. TDE can also be used as a refractive index medium for CLARITY. The potential of this method has been explored by imaging a whole transgenic mouse brain with the light sheet microscope. Moreover we apply this technique also on blocks of dysplastic human brain tissue transformed with CLARITY and labeled with different antibody. This clearing approach significantly expands the application of single and two-photon imaging, providing a new useful method for quantitative morphological analysis of structure in mouse and human brain.

The treatment of spinal cord injury by using implants that provide a permissive environment for axonal growth is in the focus of the research for regenerative therapies. Here, Raman-based label-free techniques were applied for the characterization of morphochemical properties of surgically induced spinal cord injury in the rat that received an implant of soft unfunctionalized alginate hydrogel. Raman microspectroscopy followed by chemometrics allowed mapping the different degenerative areas, while multimodal multiphoton microscopy (e.g. the combination of coherent anti-Stokes Raman scattering (CARS), endogenous two-photon fluorescence and second harmonic generation on the same platform) enabled to address the morphochemistry of the tissue at cellular level. The regions of injury, characterized by demyelination and scarring, were retrieved and the distribution of key tissue components was evaluated by Raman mapping. The alginate hydrogel was detected in the lesion up to six months after implantation and had positive effects on the nervous tissue. For instance, multimodal multiphoton microscopy complemented the results of Raman mapping, providing the micromorphology of lipid-rich tissue structures by CARS and enabling to discern lipid-rich regions that contained myelinated axons from degenerative regions characterized by myelin fragmentation and presence of foam cells. These findings demonstrate that Raman-based imaging methods provide useful information for the evaluation of alginate implant effects and have therefore the potential to contribute to new strategies for monitoring degenerative and regenerative processes induced in SCI, thereby improving the effectiveness of therapies.

We investigate a method to estimate the spectral images of reduced scattering coefficients and the absorption coefficients of in vivo exposed brain tissues in the range from visible to near-infrared wavelength (500-760 nm) based on diffuse reflectance spectroscopy using a digital RGB camera. In the proposed method, the multi-spectral reflectance images of in vivo exposed brain are reconstructed from the digital red, green, blue images using the Wiener estimation algorithm. The Monte Carlo simulation-based multiple regression analysis for the absorbance spectra is then used to specify the absorption and scattering parameters of brain tissue. In this analysis, the concentration of oxygenated hemoglobin and that of deoxygenated hemoglobin are estimated as the absorption parameters whereas the scattering amplitude a and the scattering power b in the expression of μ_s’=aλ^-b as the scattering parameters, respectively. The spectra of absorption and reduced scattering coefficients are reconstructed from the absorption and scattering parameters, and finally, the spectral images of absorption and reduced scattering coefficients are estimated. We performed simultaneous recordings of spectral diffuse reflectance images and of the electrophysiological signals for in vivo exposed rat brain during the cortical spreading depression evoked by the topical application of KCl. Changes in the total hemoglobin concentration and the tissue oxygen saturation imply the temporary change in cerebral blood flow during CSD. Change in the reduced scattering coefficient was observed before the profound increase in the total hemoglobin concentration, and its occurrence was synchronized with the negative dc shift of the local field potential.

The non-linear techniques Second and Third Harmonic Generation (SHG, THG) have been employed simultaneously to record three dimensional (3D) imaging and localize the lipid content of the muscular areas (ectopic fat) of Caenorhabditis elegans (C. elegans). Simultaneously, Two-Photon Fluorescence (TPEF) was used initially to localize the stained lipids with Nile Red, but also to confirm the THG potential to image lipids successfully. In addition, GFP labelling of the somatic muscles, proves the initial suggestion of the existence of ectopic fat on the muscles and provides complementary information to the SHG imaging of the pharynx. The ectopic fat may be related to a complex of pathological conditions including type-2 diabetes, hypertension and cardiovascular diseases. The elucidation of the molecular path leading to the development of metabolic syndrome is a vital issue with high biological significance and necessitates accurate methods competent of monitoring lipid storage distribution and dynamics in vivo. THG microscopy was employed as a quantitative tool to monitor the lipid accumulation in non-adipose tissues in the pharyngeal muscles of 12 unstained specimens while the SHG imaging revealed the anatomical structure of the muscles. The ectopic fat accumulation on the pharyngeal muscles increases in wild type (N2) C. elegans between 1 and 9 days of adulthood. This suggests a correlation of the ectopic fat accumulation with the aging. Our results can provide new evidence relating the deposition of ectopic fat with aging, but also validate SHG and THG microscopy modalities as new, non-invasive tools capable of localizing and quantifying selectively lipid accumulation and distribution.

Nonlinear optical imaging techniques have created new opportunities of research in the biomedical field. Specifically, Third Harmonic Generation (THG) seems to be a suitable noninvasive imaging tool for the delineation and quantification of biological structures at the microscopic level. The aim of this study was to extract information as to the activation state of different cell types by using the THG imaging microscopy as a diagnostic tool.

BV-2 microglia cell line was used as a representative biological model enabling the study of resting and activated state of the cells linked to various pathological conditions. Third Harmonic Generation (THG) and Two Photon Excitation Fluorescence (TPEF) measurements were simultaneously collected from stained breast cancer cells, by employing a single homemade experimental apparatus and it was shown that high THG signals mostly arise from lipid bodies. Continuously, BV-2 microglia cells were examined with or without activation by lipopolysaccharide (LPS) in order to discriminate between control and activated cells based on the quantification of THG signals. Statistically quantification was accomplished in both mean area and mean intensity values of THG. The values for mean total area and mean THG intensity values have been increased in activated versus the non-activated cells. Similar studies of quantification are underway in breast cancer cells for the exact discrimination on different cell lines. Furthermore, laser polarization dependence of SHG and THG signal in unstained biological samples is investigated.

A system is presented that uses a fiber based Master Oscillator Power Amplifier (MOPA) with nanosecond-range pulses for two-photon excitation fluorescence (TPEF) imaging. The robust laser in the extended near infrared is based on an actively modulated electro-optical modulator (EOM), enabling free synchronization of the pulses to any other light source or detection unit. Pulses with a freely programmable duration between 0.4 and 10 ns are generated and then amplified to up to kilowatts of peak power with ytterbium doped fiber amplifiers (YDFA). Since we achieve peak power and duty cycles comparable to standard femto- and picosecond setups, the TPEF signal levels are similar, but realized with a robust and inexpensive fiber-based setup. The delivery fiber is further used as an optional, electronically controllable Raman shifter to effectively shift the 1064 nm light to 1122 nm and to 1186 nm. This allows imaging of a manifold of fluorophores, like e.g. TexasRed, mCherry, mRaspberry and many more. We show TPEF imaging of the autofluorescence of plant leaves of moss and algae, acquired in epi-direction. This modular laser unit can be integrated into existing systems as either a fiber-based, alignment free excitation laser or an extension for multi-modal imaging.

Recently, tremendous improvements have been achieved in the precision of localization of single fluorescent molecules, allowing localization and tracking of biomolecules at the nm level. Since the behaviour of proteins and biological molecules is tightly influenced by the cell’s environment, a growing number of microscopy techniques are moving from in vitro to live cell experiments. Looking at both diffusion and active transportation processes inside a cell requires three-dimensional localization over a few microns range, high SNR images and high temporal resolution (ms order of magnitude). To satisfy these requirements we developed an automated routine that allow 3D tracking of single fluorescent molecules in living cells with nanometer accuracy, by exploiting the properties of the point-spread-function of out-of-focus Quantum Dots bound to the protein of interest.

This study’s goal is to develop a low cost, portable, accurate and comfortable NIRS module that can be used simultaneously with EEG in a dual modality system for brain computer interface (BCI). The sensing modules consist of electroencephalography (EEG) electrodes (at the positions Fp1, Fpz and Fp2 in the international 10-20 system) with eight custom made functional near infrared spectroscopy (fNIRS) channels, positioned on the prefrontal cortex area with two extra channels to measure and eliminate extra-cranial oxygenation. The NIRS sensors were designed to guarantee good sensor-skin contact, without causing subject discomfort, using springs to press them to the skin instead of pressing them by cap fixture. Two open source software packages were modified to carry out dual modality hybrid BCI experiments. The experimental paradigm consisted of a mental task (arithmetic task or text reading) and a resting period. Both oxygenated hemoglobin concentration changes (HbO), and EEG signals showed an increase during the mental task, but the onset, period and amount of that increase depends on each modality’s characteristics. The subject’s degree of attention played an important role especially during online sessions. The sensors can be easily used to acquire brain signals from different cerebral cortex parts. The system serves as a simple technological test bed and will be used for stroke patient rehabilitation purposes.

Neurodegenerative diseases usually appear at advanced age. Medical advances make people live longer and as a consequence, the number of neurodegenerative diseases continuously grows. There is still no cure for these diseases, but several brain stimulation techniques have been proposed to improve patients’ condition. One of them is Optical Neural Stimulation (ONS), which is based on the application of optical radiation over specific brain regions. The outer cerebral zones can be noninvasively stimulated, without the common drawbacks associated to surgical procedures. This work focuses on the analysis of ONS effects in stimulated neurons to determine their influence in neuronal activity. For this purpose a neural network model has been employed. The results show the neural network behavior when the stimulation is provided by means of different optical radiation sources and constitute a first approach to adjust the optical light source parameters to stimulate specific neocortical areas.