With the progress in solar physics, the higher temporal and spatial resolution for solar observation is required. Relative studies indicate that most scientific research focuses on a very small spatial scale of 50 to 100 km at the solar atmosphere, corresponding to an angle resolution of 0.1 arc sec.1 Therefore, only a solar telescope with at least 1-m aperture can satisfy the latest solar physics research. For difficulties in sealing and stress birefringence of a large aperture window, open structure gradually replaces the traditional vacuum structure for telescopes with meter-sized aperture or above. However, for solar irradiance, the primary mirror is heated and its temperature difference with the ambient air will result in mirror seeing effect2 and thermal deformation.3
To mitigate the mirror seeing effect and thermal deformation, the actively cooled primary mirror to control the mirror surface temperature is gradually being utilized in large ground-based solar telescopes. The actively cooled primary mirror has two types. One is the lightweight sandwich mirror,4 the other is the active thin mirror.5 The sketch of cooled system for two types of mirror is shown in Fig. 1. The absorbed heat transfer to the back surface of mirror and is cooled by the temperature-controlled air from the nozzle.
Currently, all the large ground-based solar telescopes in operation or under development, such as GREGOR (the German solar telescope with 1.5 m aperture),4 Goode Solar Telescope (GST),5 Daniel K. Inouye Solar Telescope (DKIST),6 European Solar Telescope (EST),7 National Large Solar Telescope (NLST),8 and Chinese Large Solar Telescope (CLST),9 are equipped with the actively cooled primary mirror. For a feedback control system, the surface temperature of primary mirror, which is the control objective, should be accurately detected.
Generally, there are two ways to detect the surface temperature of an object. One is the contact estimation method and the other is the noncontact estimation method based on infrared detection. However, due to the solar irradiance and fragility of the mirror surface coating, the contact temperature sensor cannot be adhered on the mirror surface directly. Also, the high reflectivity and the low infrared emissivity of the mirror surface coating make the infrared thermal imaging not available. As a compromise, the surface temperature of primary mirror is usually replaced by the temperature in the vicinity of the mirror surface, such as the back of the mirror face sheet or the shadows of the spiders on mirror surface,1011.–12 where the traditional temperature estimation method is available. Therefore, how to accurately measure the temperature on the surface of an actively cooled primary mirror is still an unsolved problem.
In this paper, a surface temperature estimation method for actively cooled primary mirror surface is proposed. The proposed mirror surface temperature estimation method is based on the analytical heat transfer model of the actively cooled mirror. Furthermore, the experiment is carried out to validate the proposed temperature estimation method.
Analytical Heat Transfer Modeling of Actively Cooled Primary Mirror
Heat Transfer Model of Primary Mirror
The above simplified heat transfer model can be described by a one-dimensional (1-D) transient heat transfer model (Fig. 3).
The 1-D transient heat transfer partial differential equation is applied along the -direction through the face sheet of primary mirror. For the front of the face sheet, there are convection with air, absorbed solar radiation, and thermal radiation with the environment. On the back of the face sheet, where the air jet impingement is formed, there is the forced convection between the air jet and the mirror and the thermal radiation with the environment. For lower temperatures and the emission rate of a coating with high reflectivity, the thermal radiation is neglected on both sides of face sheet. The heat transfer model of the face sheet of the actively cooled primary mirror is expressed as15
To solve Eq. (1), we discretize Eq. (1) in time and space domain. Central and forward differences are, respectively, applied for the second- and the first-order differential terms. For time stability of solution, the implicit scheme is used. The differential equations are given as
Heat Transfer Coefficient on the Front of the Face Sheet
The convection on the front of the face sheet is equivalent to the forced cooled model of a flat plate. In the model, the diameter of a round plate is the characteristic length.
According to the experiments,15 Eqs. (8)–(10) are obtained
Heat Transfer Coefficient on the Back of the Face Sheet
The air jet-cooled system on the back of the face sheet is equivalent to the single round air jet-cooled model (Fig. 4).
The is the heat transfer coefficient on the back of the face sheet. The mean heat-transfer coefficient in the jet zone of radius is expressed as15Fig. 4. Nondimensional parameters , , and are the mean Nusselt number, the Reynolds number with characteristic length , and the Prandtl number of air. and are the mean heat transfer coefficients on the plate and the thermal conductivity of the air jet.
Equation (11) is validated by the experiments when it satisfied the conditions as
Noncontact Surface Temperature Estimation Method on Actively Cooled Primary Mirror Based on the Heat Transfer Model of the Mirror Face Sheet
The noncontact surface temperature estimation method is based on the heat transfer model of actively cooled primary mirror face sheet. The proposed estimation method includes the following steps:
a. Ambient parameters definition: Sensors are used to measure the ambient air temperature (denoted as , unit: K), the outlet air jet temperature of nozzle (denoted as , unit: K), the solar irradiance (denoted as , unit: ), and the ambient air velocity (denoted as , unit: ). The sampling period of these sensors is denoted as .
b. Mirror parameter definitions: The heat conductance, the specific heat, and the density of mirror material are, respectively, denoted as (unit: ), (unit: ), and (unit: ). The thickness of the mirror face sheet is (unit: m).
c. The heat transfer coefficient on the front face sheet is obtained from a look-up table: based on the measured ambient temperature , the dynamic viscosity, and the thermal conductance and the Prandtl number of the ambient air is obtained by looking-up table. Substituting these parameters into Eqs. (8)–(10) produce the heat transfer coefficient on the front of the face sheet, which is denoted as (unit: ).
d. The heat transfer coefficient on the back of the face sheet is obtained from a look-up table: Based on the measured outlet air jet temperature of nozzle , the dynamic viscosity, and the thermal conductance and the Prandtl number of the ambient air is obtained by looking-up table. Additionally, the inner diameter, the gap between the outlet of the nozzle and the back of mirror face sheet, and the radius of the jet zone (mirror cell) are, respectively, denoted as (unit: m), (unit: m), and (unit: m). Substituting these parameters into Eqs. (11)–(13) produce the heat transfer coefficient on the back of the face sheet, which is denoted as (unit: ).
e. Mirror surface temperature calculation: Substituting the above parameters into Eq. (7) produce the estimated surface temperature of actively cooled primary mirror.
In the next section, the proposed temperature estimation method is experimentally validated in a specific actively cooled primary mirror.
Prototype of Chinese Large Solar Telescope and Its Actively Cooled Primary Mirror
To fill the gap of high-resolution solar observation in east Asia, China is planning to build a CLST with 1.8-m aperture.1617.–18 To validate a series of key technologies including the actively cooled primary mirror, the Prototype of Solar Telescope (POST) has been built19 (Fig. 5).
The primary mirror of the POST is an actively cooled honeycomb mirror made of ultralow expansion glass (ULE, Table 1). The diameter and the thickness of the primary mirror are 600 and 20 mm, respectively. The inner diameter of nozzle and the gap between nozzle and plate are 15 and 20 mm (Fig. 4), respectively. The radius of inscribed circle of hexagon cell is 45 mm.
Properties of the ULE.
|Thermal conductivity ()||1.31|
|Specific heat ()||766|
The thermal control system for honeycomb primary mirror of the POST is shown in Fig. 6.
Air jet impingement cools the back of the face sheet of primary mirror directly. Refrigerator and electrical heater collaboratively work to regulate the cooling air temperature to realize the active thermal control of the primary mirror surface. The ventilator works at a fixed frequency, and the mean outlet velocity of nozzles is . Experimental measurements of the air jet flow rate differences for the nozzles are . For mirror temperature measurement, two temperature sensors are installed at the outlet of nozzle (S1) and the front of the face sheet corresponding to the same cell [S2, Fig 7(a)]. Temperature sensor S3 is used to measure the ambient temperature. After the calibration and modification, the maximum measurement error of each temperature sensor is .
To validate the proposed temperature estimation method, a laboratory experiment has been carried out. Since there is no solar irradiance in the room, the absorbed solar irradiance equals zero. To test the thermal response of the primary mirror in the room, the refrigerator and electrical heater work alternately to produce the temperature fluctuation. The ambient temperature of the laboratory is not controlled. The following temperatures are measured: the variation in the temperature of the environment (temperature sensor S3), the front-sheet (temperature sensor S2), and the air jet in the cell (temperature sensor S1). These are identified in Fig. 6 and their variations versus time are shown in Fig. 8.
For the small temperature range () and the low humidity of the air in the room (the dehumidification is on), the properties of dry air are assumed as constant quantities. Refer to the dry air at 25 deg,15 the properties are shown in Table 2. The velocity of ambient air flow in the room is about (tested by the hot-wire anemometer of TESTO 425).
Properties of the dry air at 25 deg.
|Dynamic viscosity (unit: )|
|Thermal conductivity [unit: ()]|
Substituting the parameters into Eqs. (8)–(11), the heat transfer coefficients on the front of the face sheet and the back of the face sheet are 1.6 and , respectively.
The number of nodes is set as 20. For the sampling, frequency of temperature sensor is 0.2 Hz, the corresponding time step equals 5 s. Substituting the measured temperature into series of the environment (measured by temperature sensor S3) and the air jet in the cell (measured by temperature sensor S1) into Eq. (7), the measured temperature on the front of the face sheet is obtained (Fig. 9). Here, the calculated temperature series is the result of the proposed noncontact temperature estimation method.
To validate the proposed estimation method, the calculated result is compared with the real temperature on the mirror (measured by temperature sensor S2). The estimation error is defined as
The estimation error with time variations is shown in Fig. 10.
Figure 10 shows that the error is no . In the meanwhile, the mean value of the error is 0.14 deg. Based on the analysis, the acceptable temperature rise on mirror surface should be within 2 deg.20 Therefore, the error of the proposed noncontact temperature estimation method is acceptable.
Summary and Conclusions
In this paper, a noncontact temperature estimation method based on the analytical heat transfer model for actively cooled primary mirror is proposed. To validate the method, the experiment based on the prototype POST has been carried out. Using this method, the surface temperature on the actively cooled primary mirror surface can be obtained without traditional temperature measurement methods.
We would like to express our gratitude to Mrs. Cheng Li, Dr. Lei Zhu, Dr. Lanqiang Zhang, Mr. Jinlong Huang, Mr. Yuntao Chen, Mr. Benxi Yao, and Mr. Zhiyong Wang from Institute of Optics and Electronics, Chinese Academy of Sciences, for their help. A special acknowledgement should be shown to Professor Wenhan Jiang from the Institute of Optics and Electronics, Chinese Academy of Sciences, for his revision we benefited greatly. This work was funded by the National Natural Science Foundation of China (Nos. 11727805 and 11733005).
Yangyi Liu received his PhD in optical engineering from the Institute of Optics and Electronics, Chinese Academy of Sciences, in 2016. His interests are mainly in thermal control technology of solar telescope and postfocus instruments currently. He is also the main member of Chinese Large Solar Telescope group on its thermal control system.
Naiting Gu received his MS and PhD degrees in optical engineering from the Institute of Optics and Electronics, Chinese Academy of Sciences, in 2009 and 2012, respectively. He has researched on wavefront measurement technology and interferometry imaging technology for several years. Currently, he devotes himself to observe the solar activity, including solar observation facility, solar adaptive optics, and postfocus instruments.
Changhui Rao is the member of SPIE and OSA. He has been engaged in the research on adaptive optics and optical propagation through atmosphere for more than 20 years. More than 200 papers have been published. He is also the vice director of the Institute of Optics and Electronics and the vice director of the Key Laboratory on Adaptive Optics.