|
1.IntroductionHybrid organic–inorganic perovskites (HOIPs) have attracted a lot of research interest in the past few years because of their promising photovoltaic device applications.1,2 As a class of semiconductor, HOIPs exhibit large absorption coefficient, high carrier photogeneration efficiency, and relatively high carrier mobility.3–6 These properties lead to photovoltaic devices with power conversion efficiency approaching 22%.3 Moreover, their low-temperature solution-based processing provides simplicity and tunability for device fabrication.7 All these advantages make the HIOP strong candidate to play an important role in the semiconductor optoelectronic industry. In addition, fields other than optoelectronics have become a hot topic for research. Recently, the extraordinary spintronic properties of HOIPs have been theoretically advanced and experimentally verified.8,9 Due to lack of inversion symmetry and large spin-orbit coupling (SOC) caused by heavy metal and halogen atoms, HOIPs show large Rashba splitting in both conduction band and valance band.10 In addition, large spin relaxation time has been measured in HOIPs.11,12 Consequently, HOIP applications in spintronic device such as spin valve have become an emerging research subject. However, thin film devices based on solution-processed HOIPs suffer from the same problems as other polycrystalline or amorphous films, which are pinholes, impurities, or traps that can largely disturb spin transport in the semiconductor layer and therefore decrease the obtained magnetoresistance in spin valves.13 In order to improve the performance of spintronic devices, interplay between electrically injected spin current and photocurrent has been proposed and conducted in devices based on several organic and inorganic semiconductors.14–16 Upon illumination, the semiconductor resistance in the spin-valve interlayer can be downtuned by the photogenerated carriers and, consequently, increase the effective magnetoresistance of the device. Due to their excellent optoelectronic properties, as well as spintronic properties, HOIPs may be very effective as the active interlayer in such spin photovoltaic devices. By balancing the photocurrent with the electrically injected current at the open-circuit voltage (), the device can be turned on and off by sweeping the external magnetic field to alter the magnetization configuration of the two ferromagnetic (FM) electrodes from parallel to antiparallel. Rather than enhancing the spin aligned current upon illumination, we show that the photocurrent increases the device sensitivity for probing injected spin aligned carriers. Here, we report the fabrication and characterization of a spin photovoltaic (S-PV) device based on , which is a semiconductor from the HOIPs family. We demonstrate “on and off” current by sweeping the external magnetic field. The voltage dependence and light intensity dependence study indicate that diverging differential magnetocurrent (MC) can be achieved at balanced light intensity and applied bias voltage. We also show that the S-PV device sensitivity may be easily tuned achieving functionalities that are promising in applications, such as magnetic sensing and/or light sensing. 2.Results and DiscussionThe S-PV device structure is shown in Fig. 1(a); it is composed of two FM electrodes, namely (LSMO) and Co, and the film as interlayer. The 20-nm semitransparent LSMO film was grown onto (STO) substrate by pulsed laser deposition and patterned by photolithography. The was deposited by spin casting from solution. The solution was prepared by mixing MABr and precursors in dimethyl sulfoxide solvent, following by stirring overnight at 60°C. The LSMO bottom electrode was treated by oxygen plasma for 5 min before putting it into a glove-box (oxygen and water level ) for spin coating. The spin coating process was done at 4000 rpm speed for 60 s. Subsequently, the sample was annealed in the glove-box at 110°C for 30 mins. After cooling to ambient temperature, the sample was moved into a vacuum chamber having pressure of for deposition of 1-nm LiF followed by 15-nm Co layer as top electrode. The LiF is employed here to lower the work function of Co in order to form work function difference between Co and LSMO, which may lead to an internal electric field. Finally, a 30-nm gold film was deposited to protect the top electrode from oxidization and water vapor contamination. The magnetization M(B) hysteresis response of both LSMO and Co electrodes was measured in-situ by a homemade Sagnac interferometer17 having 20-nrad sensitivity and spot size; the in-plane magnetic field was swept at the same condition as that used for the device performance. As shown in Fig. 1(b), the two FM electrodes show different coercive field, of for LSMO and for Co. The coercive field difference allows achieving relative magnetization configuration of the two FM electrodes to be parallel or antiparallel to each other by simply sweeping the external magnetic field upward or downward. The characteristics of the S-PV device at 10 K is illustrated in Fig. 1(c), when the external magnetic field, is set, respectively, at (parallel configuration of the FM magnetizations) and at (antiparallel configuration). It is clearly seen that the response is different for the two FM magnetization configurations, indicating that the current flow through the device changes depending on the relative orientation of the FM electrode magnetization.18,19 This change of current with applied magnetic field is defined as MC, of which value is given by the relation: , where and are the currents at parallel and antiparallel magnetization, respectively, measured at the same bias voltage applied to the device. The MC(B) response was measured using four point method with Keithley 236 power supply and Keithley 2000 multimeter. A substantial MC value of has been measured in the fabricated S-PV device at 10 K with applied bias of 0.18 V, as shown in Fig. 1(d). As the external magnetic field is swept from positive to negative and vice versa, the current changes according to the magnetization configuration of the two FM electrodes. A difference, in the injected current in the antiparallel and parallel configuration () of 15 nA, is obtained. This result is surprising, since the spin transport in should be ineffective due to its large SOC. The anomalously large spin transport might originate from the Rashba splitting in the conduction band of , which may lead to relative long spin diffusion length and spin relaxation time.20 When illumination from a 521-nm diode laser with intensity of is applied to the S-PV device from the semitransparent LSMO electrode side, a photovoltaic effect has been observed at 10 K, as shown in Fig. 2. At zero applied bias, a short-circuit current, , of was measured. Moreover, the obtained characteristics response of the S-PV device under illumination is similar to previously reported HOIP photovoltaic devices [Fig. 2(c)].21 The relatively small open-circuit voltage () indicates that the S-PV device is not ideal for PV application due to the relatively small internal electric field in the device.22 We measured for the parallel configuration; importantly, the photocurrent in the antiparallel configuration is not null at this applied voltage. Therefore, a current difference, , is measured for the two magnetization configurations, as discussed above. Once the applied voltage is close to in the parallel configuration, the may be diverging since the denominator, , approches zero. As shown in Fig. 2(d), MC value can be achieved under these conditions at 10 K. A schematic view of the S-PV device operation is shown in Figs. 2(a) and 2(b). In the “parallel configuration” [Fig. 2(a)], the electric field applied to the devices equals to the internal photo-induced electric field but in the opposite direction. Therefore, the net current flowing through the device is zero, which is the definition of open-circuit voltage. One can regard the electrical injected current and photo-induced current as two individual channels. Under light illumination condition, the photoexcited electron–hole pairs ionize, resulting in electrons moving to the cathode and holes going to the anode; this generates photocurrent in the device. When the electrical injected current equals the photocurrent but flows in the opposite direction, the two current components cancel each other inside the device so that the external current is null. However, when the external magnetic field is swept leading to antiparallel configuration of the two FM magnetization directions, the electrical injected current becomes smaller [Fig. 2(b)]. By contrast, the photocurrent should not be affected by the magnetization configuration change, and thus remains unchanged. Under this condition, a net current through the device is generated. Consequently, the device current changes with the external magnetic field, leading to very large MC when the open-circuit voltage is reached. Following this “modus operandi,” the current in the device can be turned “on” and “off” by simply sweeping the external magnetic field. This is shown in Fig. 3(a), where the device current is turned “on” in the parallel configuration and “off” in the antiparallel configuration. This device operation has potential functionality for spintronic applications. Other functionalities may be also achieved by controlling the other degree of freedom of the S-PV device. For instance, light intensity, , may affect the device open-circuit voltage ( increases with ) and therefore influence the magnetic field, where the device switches on. In Fig. 3(b), we show characteristics measured at different from 0 to . It can be clearly seen that both and increase monotonically with . In Fig. 3(c), we plot the current change with sweeping magnetic field () measured at constant bias voltage of 0.18 V for different light intensities. It is seen that the baseline current changes via the photovoltaic effect with increasing . When , the current in the parallel configuration is zero and thus the calculated MC is very large. However, the current difference, , for parallel and antiparallel stays the same for different values since light irradiation does not affect the electrically injected spin aligned current. Both the measured and the obtained MC as a function of are plotted in Fig. 4(a). It is clearly seen that is independent of at fixed bias voltage since the light intensity only modifies the photocurrent. By contrast, since the photocurrent changes with , MC value varies with and diverges at that is set by the light intensity. The large change of the MC value around the diverging point indicates that the device becomes “super sensitive” to changes in and may be used as a sensitive photodetector. Because of the intermixing between the light illumination intensity and applied voltage, the MC value can be also maximized by tuning the applied bias voltage at a given . To show this functionality, we plot in Fig. 4(b) and MC as a function of the applied bias voltage at a fixed . The electrically injected spin current is dependent on the spin polarization of the two FM electrodes as well as spin injection efficiency of both interfaces, which are strongly dependent on applied bias voltage.23,24 Consequently, increases with bias voltage. Since also increases with the bias voltage [Fig. 2(c)] and crosses zero at , MC diverges at the open-circuit voltage set by . The light intensity dependence and bias voltage dependencies of the MC indicate that the device can get incredibly sensitive to even minor change of light intensity and applied voltage as well as external magnetic field close to condition. Spin injection from FM metals into semiconductor layers is known to be challenging because of the infamous “conductivity mismatch” problem.25,26 Therefore, spin injection efficiency in conventional semiconductor-based spin valves has been less than successful, with very limited MC/magnetoresistance value. However, in the S-PV device described here, we can finesse the problem of limited spin injection efficiency into the semiconductor by enhancing the sensitivity of the device using the integration of spin transport and photovoltaic properties. In this scenario, the MC value dramatically increases at . As shown in Fig. 3(a), the switch between zero and nonzero device current for parallel and antiparallel magnetization configurations renders the device useful for complex magnetic and/or light sensor. Moreover, since the base current is set to zero but minor changes in the spin current can be still sensed, the S-PV device should require less energy consumption than traditional spin valves. 3.ConclusionAs a class of semiconductor, the application of HOIPs in the optoelectronics field has developed quickly, reaching limits comparable to those of conventional inorganic photovoltaic materials. This surprising advancement stimulates exploration of other possible application of the HOIPs. In the present work, we propose a spin photovoltaic device based on this emerging material family. Such a device takes advantage of the HOIP excellent optoelectronic properties and efficient spintronic properties, which render its performance better than similar devices based on competing compounds. Due to the intermixing of different degrees of freedom in this device, control over the MC value can be readily achieved. We therefore conclude that the S-PV device paves the way for HOIPs to enter fields other than optoelectronics. AcknowledgmentsThis work was supported by the Department of Energy Office of Science under Grant No. DE-SC0014579. The device fabrication facility and C.Z. were supported in part by the National Science Foundation-Material Science & Engineering Center (NSF-MRSEC) program at the University of Utah under Grant No. DMR 1121252. H.G. was supported by the US Department of Energy (DOE) under Grant No. DOE DE-SC0002136. ReferencesM. M. Lee et al.,
“Efficient hybrid solar cells based on meso-superstructured organometal halide perovskites,”
Science, 338 643
–647
(2012). https://doi.org/10.1126/science.1228604 SCIEAS 0036-8075 Google Scholar
M. Liu, M. B. Johnston and H. J. Snaith,
“Efficient planar heterojunction perovskite solar cells by vapour deposition,”
Nature, 501 395
–398
(2013). https://doi.org/10.1038/nature12509 Google Scholar
W. S. Yang et al.,
“High-performance photovoltaic perovskite layers fabricated through intramolecular exchange,”
Science, 348 1234
–1237
(2015). https://doi.org/10.1126/science.aaa9272 SCIEAS 0036-8075 Google Scholar
L. Dou et al.,
“Solution-processed hybrid perovskite photodetectors with high detectivity,”
Nat. Commun., 5 5404
(2014). https://doi.org/10.1038/ncomms6404 NCAOBW 2041-1723 Google Scholar
Q. Dong et al.,
“Electron-hole diffusion in solution-grown single crystals,”
Science, 347 967
–970
(2015). https://doi.org/10.1126/science.aaa5760 SCIEAS 0036-8075 Google Scholar
D. Shi et al.,
“Low trap-state density and long carrier diffusion in organolead trihalide perovskite single crystals,”
Science, 347 519
–522
(2015). https://doi.org/10.1126/science.aaa2725 SCIEAS 0036-8075 Google Scholar
H. Cho et al.,
“Overcoming the electroluminescence efficiency limitations of perovskite light-emitting diodes,”
Science, 350 1222
–1225
(2015). https://doi.org/10.1126/science.aad1818 SCIEAS 0036-8075 Google Scholar
M. Kepenekian et al.,
“Rashba and Dresselhaus effects in hybrid organic-inorganic perovskites: from basics to devices,”
ACS Nano, 9 11557
–11567
(2015). https://doi.org/10.1021/acsnano.5b04409 ANCAC3 1936-0851 Google Scholar
D. Niesner et al.,
“Giant Rashba splitting in organic-inorganic perovskite,”
Phys. Rev. Lett., 117 126401
(2016). https://doi.org/10.1103/PhysRevLett.117.126401 PRLTAO 0031-9007 Google Scholar
Z.-G. Yu,
“Rashba effect and carrier mobility in hybrid organic-inorganic perovskites,”
J. Phys. Chem. Lett., 7 3078
–3083
(2016). https://doi.org/10.1021/acs.jpclett.6b01404 JPCLCD 1948-7185 Google Scholar
P. Odenthal1 et al.,
“Spin-polarized exciton quantum beating in hybrid organic-inorganic perovskites,”
Nat. Phys., 13 894
–899
(2017). https://doi.org/10.1038/nphys4145 NPAHAX 1745-2473 Google Scholar
D. Giovanni et al.,
“Highly spin-polarized carrier dynamics and ultralarge photoinduced magnetization in perovskite thin films,”
Nano Lett., 15 1553
–1558
(2015). https://doi.org/10.1021/nl5039314 NALEFD 1530-6984 Google Scholar
P. Burrows and S. Forrest,
“Electroluminescence from trap‐limited current transport in vacuum deposited organic light emitting devices,”
Appl. Phys. Lett., 64 2285
–2287
(1994). https://doi.org/10.1063/1.111645 APPLAB 0003-6951 Google Scholar
F. Bottegoni et al.,
“Spin voltage generation through optical excitation of complementary spin populations,”
Nat. Mater., 13 790
–795
(2014). https://doi.org/10.1038/nmat4015 NMAACR 1476-1122 Google Scholar
R. Jansen,
“Spintronics: solar spin devices see the light,”
Nat. Mater., 12 779
–780
(2013). https://doi.org/10.1038/nmat3745 NMAACR 1476-1122 Google Scholar
X. Sun et al.,
“A molecular spin-photovoltaic device,”
Science, 357 677
–680
(2017). https://doi.org/10.1126/science.aan5348 SCIEAS 0036-8075 Google Scholar
J. Xia et al.,
“Modified Sagnac interferometer for high-sensitivity magneto-optic measurements at cryogenic temperatures,”
Appl. Phys. Lett., 89 062508
(2006). https://doi.org/10.1063/1.2336620 APPLAB 0003-6951 Google Scholar
M. N. Baibich et al.,
“Giant magnetoresistance of (001)Fe/(001)Cr magnetic superlattices,”
Phys. Rev. Lett., 61 2472
–2475
(1988). https://doi.org/10.1103/PhysRevLett.61.2472 PRLTAO 0031-9007 Google Scholar
Z. Xiong et al.,
“Giant magnetoresistance in organic spin-valves,”
Nature, 427 821
–824
(2004). https://doi.org/10.1038/nature02325 Google Scholar
F. Zheng et al.,
“Rashba spin-orbit coupling enhanced carrier lifetime in ,”
Nano Lett., 15 7794
–7800
(2015). https://doi.org/10.1021/acs.nanolett.5b01854 NALEFD 1530-6984 Google Scholar
N. J. Jeon et al.,
“Compositional engineering of perovskite materials for high-performance solar cells,”
Nature, 517 476
–480
(2015). https://doi.org/10.1038/nature14133 Google Scholar
S. Ryu et al.,
“Voltage output of efficient perovskite solar cells with high open-circuit voltage and fill factor,”
Energy Environ. Sci., 7 2614
–2618
(2014). https://doi.org/10.1039/C4EE00762J EESNBY 1754-5692 Google Scholar
M. Kohda et al.,
“Bias voltage dependence of the electron spin injection studied in a three-terminal device based on a (Ga,Mn)As/-GaAs Esaki diode,”
Appl. Phys. Lett., 89 012103
(2006). https://doi.org/10.1063/1.2219141 APPLAB 0003-6951 Google Scholar
J. M. De Teresa et al.,
“Role of metal-oxide interface in determining the spin polarization of magnetic tunnel junctions,”
Science, 286 507
–509
(1999). https://doi.org/10.1126/science.286.5439.507 SCIEAS 0036-8075 Google Scholar
G. Schmidt et al.,
“Fundamental obstacle for electrical spin injection from a ferromagnetic metal into a diffusive semiconductor,”
Phys. Rev. B, 62 R4790
(2000). https://doi.org/10.1103/PhysRevB.62.R4790 Google Scholar
E. Rashba,
“Theory of electrical spin injection: tunnel contacts as a solution of the conductivity mismatch problem,”
Phys. Rev. B, 62 R16267
(2000). https://doi.org/10.1103/PhysRevB.62.R16267 Google Scholar
BiographyJingying Wang received her PhD in physics from North Carolina State University in 2016. She is currently a postdoc researcher working with Prof. Valy Vardeny in the Department of Physics and Astronomy of University of Utah. Her research interest focuses on spintronic properties of organic semiconductor and hybrid perovskite. Xin Pan received his BS degree in physics from the University of Science and Technology in China. He is now a PhD candidate in the Department of Physics and Astronomy of University of Utah. Chuang Zhang received his PhD in chemistry from Chinese Academy of Science. He was postdoc working with Prof. Valy Vardeny for three years. Now, he is an assistant professor in the Institute of Chemistry, Chinese Academy of Science. Hangwen Guo received his PhD from the University of Tennessee and then worked as a postdoc in Louisiana State University. Now, he is an assistant professor of Fudan University in shanghai, China. Zeev Valy Vardeny received his PhD in physics from Technion University in 1979. He joined the Department of Physics and Astronomy of Univerisity of Utah as a professor in 1987. His research focuses on optical, electrical and magnetic properties of organic semiconductors and other novel materials, as well as devices based on them. |