1 June 2005 Wavelength stability optimization of L-band superfluorescent fiber source
Author Affiliations +
Optical Engineering, 44(6), 060504 (2005). doi:10.1117/1.1928271
A new bidirectional pumped configuration for an L-band erbium-doped superfluorescent fiber source is demonstrated. Data are presented showing that with this configuration, the mean wavelength variation with the pump power can be reduced to zero by optimizing the fiber length and the pumping ratio of forward to total pump power.
Wang and Huang: Wavelength stability optimization of L-band superfluorescent fiber source



Superfluorescent fiber source (SFS) using amplified spontaneous emission (ASE) from an erbium-doped fiber (EDF) has been a topic of continuing research because of its wide range of applications.1 2 In particular, in fiber optic gyroscope (FOG) applications, the mean wavelength stability of the SFS is vital since it determines the accuracy of rotation detection of the FOG. On the other hand, the bandwidth is another important parameter since a SFS with a broad bandwidth implies that a higher SNR would be obtained from the FOG. In the past decades, various designs of SFSs have been demonstrated with the aim to improve these two performance parameters.3 4 5 However, all of the high-stability SFSs reported so far were restricted to the C-band SFS. Although it has the potential for a flatter spectrum, there are no reports on a high-stability L-band SFS because both theoretical and experimental results show that it cannot have pump-power-independent mean-wavelength operation with a single laser pump.1 6 In this letter, we demonstrate a new configuration for the mean-wavelength stability L-band SFS. A single laser diode has replaced the pair of pump diodes used in Ref. 7 to avoid the pump power variation of backward pump or forward pump, respectively. As a result, the mean-wavelength variation with pump power can be reduced to zero by optimizing the fiber length and the pumping ratio of forward to total pump power.


Configuration and Results

The suggested configuration of the L-band erbium-doped SFS is shown in Fig. 1, which consists of a section of EDF, two 1480/1590-nm wavelength division multiplexers (WDMs), a 1480-nm pump laser diode (LD), a power splitter used to divide the pump power into two portions, a fiber mirror with nearly 100 reflectivity made by a 3-dB fiber couple, and an optical isolator (ISO) at the output port. The fiber mirror is used to reflect the ASE, then causes the wide and flat L-band ASE light to emerge from the output port. Therefore, this SFS design is a double-pass bidirectional pumped configuration. The EDF used in both the numerical simulations and experiments was a Lucent Technologies heavily doped LRL fiber with a peak absorption of 27–33 dB/m at 1530 nm.

Fig. 1

Proposed configuration for mean-wavelength stability L-band SFS.


As the spectral wavelength range and flatness of the SFS with bidirectional pump are length dependent, to obtain the L-band output, the EDF length should be selected properly in order to make the ASE generated by the forward pump move to L-band. An optimum length of 19 m of LRL fiber is suitable for the double-pass bidirectional pumped L-band SFS configuration to obtain the flattest L-band SFS spectrum by the previous simulation.8

Figure 2 illustrates the calculated mean-wavelength variation and the pump efficiency versus pumping ratio (Rp=P forward /P total ) for the total pump power fixed at 100 mW. Commercial EDF optical amplifier simulation software was used for the simulations.9 The rate equations, power evolution equations, and boundary conditions of the SFS configuration were completed by the simulation software. The software was used to characterize SFS and is shown to be effective.5 It is found from the results that two pumping ratios exist where the mean wavelength is independent of the small variations in the power splitting ratio of the power splitter. These two pumping ratios correspond to Rp=0.2 and 0.5. These two values are significant because the splitting ratio may have small variations with the ambient temperature and total pump power, etc. Figure 2 also shows that the pump efficiency decreases with the pumping ratio. The pump efficiency is 62.66 for Rp=0.2 and 54.6 for Rp=0.5 when the loss is negligible.

Fig. 2

Calculated mean wavelength and pump efficiency versus pumping ratio with the total pump power fixed at 100 mW.


Figure 3 shows the calculated mean wavelength as a function of the total pump power for these two significant pumping ratios of 0.2 and 0.5, respectively. The results show that for Rp=0.5, the pump power independent mean-wavelength operation, i.e., λ¯/∂P total =0, does not exist for large pump power of this fiber source. However, for Rp=0.2, the pump-power-independent mean-wavelength operation was obtained when the pump power was approximately 75 mW.

Fig. 3

Calculated mean wavelength as a function of the total pump power with Rp=0.2 and 0.5.


On the basis of the above simulations, the mean wavelength and output power against the total pump power for a pumping ratio of 0.2 and EDF length of 19 m were measured, and the results are shown in Fig. 4. The experimental results are in good agreement with the simulation. The pump-power-independent mean-wavelength operation was observed when the pump power was 82 mW. The inset in Fig. 4 shows the output L-band SFS spectrum for a pump power of 82 mW. The total SFS output power is 34 mW with a linewidth of 42.6 nm.

Fig. 4

Measured output power and mean wavelength versus pump power with Rp=0.2 and L EDF =19 m. Inset: SFS spectrum for a pump power of 82 mW.


By replacing a pair of pump diodes by a single laser diode in the bidirectional pumped configuration, a L-band SFS with pump-power-independent mean-wavelength operation was achieved by optimization. From the L-band SFS spectrum inset in Fig. 4, it can be seen that the L-band SFS spectrum has two humps with the double-pass bidirectional pumped configuration; one is around 1570 nm and the other is around 1600 nm. Synchronous changes of the backward and forward pump power with a proper pumping ratio ensure no fluctuation between the two humps as pump power increases in a certain pump power region, thus the mean wavelength variation versus the pump power is reduced to zero. Namely, the population distribution in the upper state remains unchanged with pump power variation (i.e., the backward pump and forward pump variation are synchronous) in a certain pump power region with a proper pumping ratio. However, the population distribution cannot remain unchanged with pump power variation of the backward pump or forward pump, respectively. The population distribution in the upper state determines the emission spectrum. Therefore, the unchanged distribution implies that a SFS with mean-wavelength stability can be obtained. As the spectral output power of the SFS is affected by the reflectivity of the fiber mirror,7 the optimization values of the EDF length and pumping ratio are dependent on the reflectivity of the fiber mirror.



In conclusion, we have characterized a practical design of the L-band SFS of a bidirectional pump configuration. By ensuring pump power variations of the forward and backward pump simultaneously with a power splitter, the λ¯/∂P total instability, a limiting problem for high-precision fiber optic gyroscopes, can be reduced to zero for a chosen EDF length by optimizing the pumping ratio. A mean-wavelength stability L-band SFS with a linewidth of 42.6 nm, an output power of 34 mW was experimentally obtained. Advantages of the proposed L-band SFS are high mean-wavelength stability, broad linewidth, and high output power.


This work was supported by the Natural Science Foundation of Fujian Province under Grant No. A0440009 and Fujian Provincial Key Laboratory of Photonic Technology under Grant No. FP0408.


1.  P. F. Wysocki , M. J. F. Digonnet , B. Y. Kim , and H. J. Shaw , “Characteristics of erbium-doped superfluorescent fiber sources for interferometric sensor applications,” J. Lightwave Technol. 12(3), 550–567 (1994).  Google Scholar

2.  C. D. Su and L. A. Wang , “Multiwavelength fiber sources based on double-pass superfluorescent fiber sources,” J. Lightwave Technol. 18(5), 708–714 (2000).  Google Scholar

3.  L. A. Wang and C. D. Chen , “Stable and broadband Er-doped superfluorescent fiber sources using double-pass backward configuration,” Electron. Lett. 32(19), 1815–1817 (1996).  Google Scholar

4.  B. Yang , H. Ming , Y. Guo , and J.-P. Xie , “Flattening spectrum of a broadband and wavelength stable erbium doped superfluorescent fiber source,” Chin. Phys. Lett. 16(5), 356–357 (1999).  Google Scholar

5.  P. Z. Zatta and D. C. Hall , “Ultra-stability two-stage superfluorescent fiber source for fiber optics gyroscope,” Electron. Lett. 38(9), 406–408 (2002).  Google Scholar

6.  L. A. Wang and C. D. Chen , “Characteristics comparison of Er-doped double-pass superfluorescent fiber sources pumped near 980 nm,” IEEE Photonics Technol. Lett. 9(4), 446–448 (1997).  Google Scholar

7.  S.-C. Tsai , T.-C. Tsai , P.-C. Law , and Y.-K. Chen , “High pumping-efficiency L-band erbium-doped fiber ASE source using double-pass bidirectional-pumping configuration,” IEEE Photonics Technol. Lett. 15(2), 197–199 (2003).  Google Scholar

8.  X. Wang and W. Huang , “High efficiency and stability L-band erbium-doped superfluorescent fiber source,” Proc. SPIE 5280, 221–224 (2003).  Google Scholar

9. OASIX v3.0: Lucent Technologies erbium doped fiber devices simulation software. Google Scholar

Xiulin Wang, Wencai Huang, "Wavelength stability optimization of L-band superfluorescent fiber source," Optical Engineering 44(6), 060504 (1 June 2005). https://doi.org/10.1117/1.1928271


Coherent properties of FBG-based external cavity diode lasers
Proceedings of SPIE (February 19 2004)
Linear & Nonlinear Frequency Converters
Proceedings of SPIE (January 30 1987)
Dichroic mirror for diode-pumped YAG:Nd laser
Proceedings of SPIE (August 19 1996)

Back to Top