1 December 2006 Experimental and theoretical characterization of optical signal out-coupling through V-grooved optical fiber cladding
Author Affiliations +
We demonstrate a highly efficient in-fiber out-coupling device. The core mode is coupled to the cladding by a tilted fiber Bragg grating and then the cladding mode is out-coupled from the optical fiber through V-grooved cladding. The light emitting characteristics are investigated experimentally and a maximum out-coupling efficiency of 54.8% is obtained.



Optical fiber Bragg gratings (FBGs) have been used for optical communication and sensing systems because of their unique wavelength selectivity as well as their compact, flexible, and cost-effective properties. FBGs are usually fabricated in the core region and make it possible to realize fiber in-line devices. In addition, tilted FBGs (TFBGs) are good for sensing the power of the core mode because they can couple the core mode to the cladding mode and/or radiation mode. By directly coupling the core mode to the radiation mode, fiber in-line types of spectrometers1, 2, 3 and monitors4 have been developed, which have a coupling efficiency of mostly 0.13% . Because of the low efficiency, they are not suitable for high-sensitivity optical receivers.

In this work, we present a new method that can be applied to the development of new devices for optical communications. Instead of utilizing the radiation mode, the cladding mode is used in this application. In this case, determining how to out-couple the cladding mode from the fiber is a matter of great concern. In consideration of this, the cladding is etched to efficiently out-couple the cladding mode. In our device, two kinds of coupling processes occur. One is the strong core-to-cladding mode coupling by TFBGs and the other is the highly efficient out-coupling of the cladding mode through the V-grooved cladding. Usually, the core-to-cladding mode coupling creates an undesirable crosstalk effect, which results in degradation of the optical communication systems5; however, this coupling is necessary to our applications.6



The rigorous theoretical analysis of the core-to-cladding mode coupling by TFBGs has been well explained in previous studies.7, 8, 9, 10 The coupling between the modes is maximized if one of the following phase-matching conditions is satisfied:




where n01co and nlmcl are effective indices of the fundamental core mode and the (lm) -cladding mode, respectively, l and m are the azimuthal and radial mode number, respectively, Λ is the untilted grating period, λco-co and λco-cl are resonance wavelengths for the core-to-core mode coupling and core-to- (lm) -cladding mode coupling, respectively, and θ is an actual grating tilt angle. Once the effective indices are calculated by mode analysis, the proper θ can be calculated from Eq. 2 to induce the core-to- (lm) -cladding mode coupling.

The device structure and the overall mode coupling process are depicted in Fig. 1 and the two kinds of coupling are well described in this figure. Importantly, by the effect of total internal reflection (TIR), the cladding mode is out-coupled through the V-grooved cladding.

Fig. 1

(a) Schematic appearance of the device and (b) overall mode coupling process.


As mentioned before, TFBGs are used for core-to-cladding mode coupling. Therefore, the tilt angle θ is adjusted to maximize the coupling efficiency at λco-cl instead of λco-co so that most power of the core mode is coupled to the cladding mode. The TFBG is fabricated in a hydrogen-loaded photosensitive fiber (PS1250/1500, Fibercore Ltd., Southhampton, UK) using a KrF excimer laser. The tilt angle of the phase mask is set to 2deg , which corresponds to θ2.97deg for the actual grating tilt angle.11 Figure 2 shows the transmission spectrum of the TFBG right after fabrication. As shown in this figure, the maximum core-to-cladding mode coupling occurs at λ1=1548.46nm and the coupling ratio is about 30dB (99.9%) . Figure 3 shows the fabricated V-grooved cladding and the light-emitting characteristic. The cladding is cut out by the femtosecond laser. A portion of the cladding can be precisely detached by appropriately focusing the high-power laser beam. The size of the V-groove is about 125(width)×90(length)×45(depth)μm3 .

Fig. 2

Transmission spectrum of the fabricated TFBG.


Fig. 3

Fabricated V-grooved cladding by the femtosecond laser: (a) top view, (b) side view, and (c) infrared camera view of the light of the out-coupled cladding mode at λ=1549.13nm .


Once the core mode is coupled to the cladding mode, it propagates in the cladding region and is tightly guided by the air-cladding boundary. Subsequently the cladding mode meets the V-grooved cladding on the way to propagation. Since the refractive index of the air is lower than that of the cladding, TIR occurs as long as the light incident angle to the V-groove is higher than the critical angle. At the operating wavelength, the refractive index of the cladding is about 1.44. As a result, the critical angle is about 44deg . Since the angle of the V-grooved cladding is 45deg , the TIR is satisfied and the most of the cladding mode can be out-coupled to the detector as shown in Fig. 3c. Theoretically, about half of the cladding mode can be out-coupled since the V-groove can reflect only in one side of the cladding mode as shown in Fig. 1b.



In our experiment, we measured the output photocurrent of an avalanche photodiode (APD, 124NLVT Cyoptics, Breinigsville, PA) and the transmitted power with respect to the wavelength, and then we calculated the maximum coupling efficiency of the device. Figure 4 briefly shows the measurement setup. Using the tunable laser source, the wavelength is swept from 1540to1554nm by increments of 0.02nm while the power is maintained at 1mW . On the other hand, the integrating sphere is placed near the end of the fiber to measure the transmission spectrum of the TFBG. Figure 5 shows the measured data. The solid and open circles are photocurrents of the APD and transmitted power, respectively. Since there is no core-cladding mode coupling in the longer wavelength region, there is no photocurrent evidently. The peak wavelength discrepancy of the transmission spectrum between Figs. 2 and 5 is due to the grating stabilization after fabrication. There are local maxima values in the photocurrent and definitely those occur at the wavelengths where the core-to-cladding mode coupling is strong. On the other hand, the maximum photocurrent is measured at λ2=1545.86nm but the maximum core-to-cladding mode coupling occurred at a different wavelength, i.e., λ1 . This is because, in our guess, the out-coupling efficiency depends on whether the core mode is coupled to a lower or higher cladding mode. In this point of view, the core mode seems to be coupled to the high-order and low-order cladding mode for λ1 and λ2 , respectively.

Fig. 4

Measurement setup. The APD is used to detect the light of the out-coupled cladding mode and the integrating sphere is used for the transmitted power.


Fig. 5

Measured data. The solid line is the photocurrent of the APD and the dotted line is the transmission spectrum.


Because of the adaptor loss, the actual power launched into the device is different from the tunable laser source source power and is estimated to be about 0.73mW obtained from the transmission spectrum in Fig. 5. The maximum photocurrent is about 0.4mA and corresponds to 0.4mW , in which the multiplying factor M=9 is applied. Therefore, in consideration of M , the out-coupling efficiency is about 54.8%(=0.4mW0.73mW) .



We fabricated a novel out-coupling device that has a V-grooved cladding. The theoretical out-coupling efficiency is limited by the maximum core-to-cladding coupling ratio, which is 99.9% in our device, and the obtained out-coupling efficiency is 54.8%. According to our experience, the out-coupling efficiency can be improved by optimizing the grating and V-grooved cladding. In our device, the optical signal can be directly detected from the fiber without using any lenses, filters, or splitters. Since this device has wavelength-division-multiplexing (WDM) characteristics inherited from the TFBG, the receiver array for WDM signals can be implemented by cascading the device with different grating parameters. The fiber in-line type also makes it possible to develop small-size optical communication devices such as transceivers, receivers, and monitoring devices.


1.  J. L. Wagener, T. A. Strasser, J. R. Pedrazzani, J. DeMarco, and D. J. DiGiovanni, “Fiber grating optical spectrum analyzer tap,” Eur. Conf. Opt. Commun. 5, 65–68 (1997). Google Scholar

2.  S. Wielandy and S. C. Dunn, “Tilted superstructure fiber grating used as a Fourier-transform spectrometer,” Opt. Lett.0146-9592 10.1364/OL.29.001614 29(14), 1614–1616 (2004). Google Scholar

3.  K. S. Feder, P. S. Westbrook, J. Ging, P. I. Reyes, and G. E. Carver, “In-fiber spectrometer using tilted fiber gratings,” IEEE Photonics Technol. Lett.1041-1135 10.1109/LPT.2003.813414 15(7), 933–935 (2003). Google Scholar

4.  Q. Li, C.-H. Lin, A. A. Au, and H. P. Lee, “Compact all-fiber on-line power monitor via core-to-cladding mode coupling,” Electron. Lett.0013-5194 10.1049/el:20020674 38(18), 1013–1015 (2002). Google Scholar

5.  I. Riant, C. Muller, T. Lopez, V. Croz, and P. Sansonetti, “New and efficient technique for suppressing the peaks induced by discrete cladding mode coupling in fiber slanted Bragg grating spectrum,” Opt. Fiber Commun. 1, 118–120 (2000). Google Scholar

6.  S. Yoon, S. Lee, H. Kang, J. Jeong, C. Yu, and B. Kim, “Highly efficient, wavelength-selective out-coupling of cladding mode using tilted fiber grating and micro-etched cladding,” Opt. Fiber Commun., OFP6 (2006). Google Scholar

7.  T. Erdogan and J. E. Sipe, “Tilted fiber phase gratings,” J. Opt. Soc. Am. A0740-3232 13(2), 296–313 (1996). Google Scholar

8.  T. Erdogan, “Fiber grating spectra,” J. Lightwave Technol.0733-8724 10.1109/50.618322 15(8), 1277–1294 (1997). Google Scholar

9.  L. Dong, B. Ortega, and L. Reekie, “Coupling characteristics of cladding modes in tilted optical fiber Bragg gratings,” Appl. Opt.0003-6935 37(22), 5099–5105 (1998). Google Scholar

10.  K. S. Lee and T. Erdogan, “Fiber mode coupling in transmissive and reflective tilted fiber gratings,” Appl. Opt.0003-6935 39(9), 1394–1404 (2000). Google Scholar

11.  C. Jauregui, A. Quintela, J. Echevarria, O. M. Conde, and J. M. Lopez-Higuera, “Experimental characterization of tilted fiber Bragg gratings,” Opt. Fiber Commun. 1, 159–162 (2002). Google Scholar

© (2006) Society of Photo-Optical Instrumentation Engineers (SPIE)
Seihyoung Lee, Seihyoung Lee, Shinyoung Yoon, Shinyoung Yoon, Jongjin Lee, Jongjin Lee, Chonghee Yu, Chonghee Yu, Hyunseo Kang, Hyunseo Kang, } "Experimental and theoretical characterization of optical signal out-coupling through V-grooved optical fiber cladding," Optical Engineering 45(12), 120503 (1 December 2006). https://doi.org/10.1117/1.2402120 . Submission:

Back to Top