Translator Disclaimer
1 September 2008 Improved beam uniformity in multimode fibers using piezoelectric-based spatial mode scrambling for medical applications
Author Affiliations +
We improve the beam uniformity passing through multimode fibers using piezoelectric-based spatial mode scrambling. Both fiber squeezing and stretching techniques are applied and compared. A more than sixfold difference in the power intensity crossing the output beam profile without mode scrambling can be reduced to a <10% variation. The efficiency of collecting useful optical power for detection is also significantly improved. Such modules can find various applications in medical imaging, disease diagnosis, and local area networks.



Having a uniformly distributed light beam is highly desirable for various applications where multimode fibers (MMFs) are used as the light transmission or guiding media. In addition to conventional applications, including optical local area networks (LANs) over MMF and image encryptions, recent advances in genetic analysis and functional genomics, such as massively parallel signature sequencing (MPSS) and molecular interactions, have made the practical and reliable requirements more and more critical.1, 2, 3, 4

Mode scrambling has been a well-known technique to improve the uniformity in multimode fibers. So far, various approaches have been demonstrated: (i) modifying the multimode fiber itself, as through extremely high-temperature annealing5 or special fabrication in the cladding;6 (ii) twisted plastic optical fiber instead of traditional MMF;7 (iii) selecting one special mode through mode coupling.8 These approaches suffer from one or more disadvantages, such as quality uncertainty or extreme manufacture requirements, higher cost of the fiber itself, or introducing considerable loss. Providing a more practical solution with longer lifetime and reliable performance is one of the major challenges for various mentioned applications.

In this letter, we demonstrate the improvement of beam uniformity through MMF using spatial mode scrambling. This is accomplished through either fiber squeezing or fiber stretching. Both approaches are based on the practical and well-qualified piezoelectric actuator technology. The output beam uniformity after the step-indexed MMF is analyzed and compared. The intensity fluctuations are reduced significantly; as an example, using the fiber squeezing technique, a more than sixfold relative (normalized) power intensity fluctuation without mode scrambling can be reduced to an almost uniform distribution ( <10% variation).



In order to improve the beam uniformity, we use two different schemes, as shown in Fig. 1, both based on piezoelectric actuator technology. Figure 1a uses fiber squeezing to generate spatial mode scrambling inside the optical fiber itself. Figure 1b shows a scheme that uses the piezoelectric actuator to stretch the MMF.

Fig. 1

Conceptual diagram of multimode fiber (MMF) mode scrambler: (a) using fiber-squeezing technology: six electrically driven fiber squeezers are applied along the MMF with different orientation between sections; (b) using fiber-stretching technique with MMF: four piezoelectric actuators are used to produce longitudinal extension.


In Fig. 1a, the mode scrambler consists of the multimode fiber itself (we use a step-index MMF) and six sections of fiber squeezers. These fiber squeezers add stress through piezoelectric actuators at different orientations on the multimode fiber, typically with a 45-deg shift between adjacent sections (0, 45, 0, 45, 0, and 45deg in the illustrated example). Driving signals are applied with different frequencies (or even amplitudes if necessary) to further randomize the mode coupling along the multimode fiber (mostly around 500Hz , with slight differences in our experiments). The amplitudes of the driving signals are all close to 150V , which is the limit of our driving circuits.

In Fig. 1b for the case using fiber stretching, a fiber coil (with a step-index MMF) is made on a fiber stretcher frame. Instead of applying stress to the fiber, the piezoelectric actuators (four are used) are driven to provide longitudinal extension at high frequencies (2.4kHz) , thereby generating spatial mode scrambling along the MMF. Since the driving frequencies are near resonance frequencies of the actuators (the resonance window is several hundred hertz, not sensitive to frequency drift), the amplitudes of the applied signals are much less than in the fiber-squeezing approach (typically 30V ), a potential advantage for practical applications.


Experimental Results and Discussion

To evaluate the performance of our approaches, we set up a testing stage (Fig. 2) where a beam analyzer is used to detect the output beam profile after the MMF. The wavelength of the light source is set to 635nm (Thorlabs LPS-635-FC fiber-coupled laser). Electrical signals are generated by our circuit and applied to piezodrivers to provide either fiber squeezing or stretching (six and four driving signals are used for the squeezing and the stretching, respectively). The aperture of the beam analyzer is set to 420μm , and the final beam profile (data) is recorded in the computer, generally with an 80-ms integration time. The insertion loss of the fiber-squeezing module is typically <0.5dB (including the connector loss); for the stretching modules it is 0.8dB

Fig. 2

Evaluation setup of the mode scrambler using either fiber squeezing or fiber stretching through MMF.


The final improvements are compared in Fig. 3. Figure 3a is the beam profile without mode scrambling, while Fig. 3b and 3c show the profile improvement using fiber squeezing and fiber stretching, respectively. The effectiveness of both approaches is abvious. The X-Y beam analyses crossing the center of the output light are also displayed next to the beam profiles for each case. We note that the intensity fluctuation without mode scrambling is more than 6 times (e.g., between 0.15 and 1.0 after normalization); while with mode scrambling, the fluctuation is reduced to <10% and <20% for the fiber squeezing and stretching, respectively. In fact, the figures of merit of the spatial mode scrambling include not only the deviation of the beam uniformity, but also the efficiency of collecting more optical power into the useful detection area (for better illumination), because the light will diffuse more without mode scrambling. If we define the scrambling efficiency as the percentage of the effective optical power into the detection area, the corresponding efficiencies are 40% (without mode scrambling), 78% (with fiber stretching), and 84% (with fiber squeezing).

Fig. 3

Improvement of the light uniformity through mode scrambling (both traces X and Y lie at the center of the profile): (a) without scrambling, (b) using fiber-squeezing, (c) using fiber stretching.


It is interesting to see that the beam uniformity using fiber squeezing is better than that using fiber stretching. We believe that this is mainly due to more random spatial scrambling along the six squeezing sections than with only one direction (i.e., longitudinal) of stretching. This is also a possible reason that a dip exists at the center of the power distribution [Fig. 3c] for the stretching case. On the other hand, because the fiber is much longer (tens of meters) and the piezoelectric actuators are driven at higher frequencies, the overall uniformity is still improved a lot through fiber stretching.



Significantly improved beam uniformity passing through MMF was realized through fiber squeezing or fiber stretching. Such mode scramblers are key modules for various applications, including medical imaging, disease diagnosis, and local area networks.


The authors would like to thank Karen Li and Peter Betts at General Photonics Corp. for help in the measurements.



A. D. Mehta, J. T. Finer, and J. A. Spudich, “Detection of single-molecule interactions using correlated thermal diffusion,” Proc. Natl. Acad. Sci. U.S.A., 94 7927 –7931 (1997). 0027-8424 Google Scholar


Y. T. Chen, M. J. Scanlan, C. A. Venditti, R. Chua, G. Theiler, B. J. Stevenson, C. Iseli, A. C. Gure, T. Vasicek, R. L. Strausberg, C. V. Jongeneed, L. J. Old, and A. J. G. Simpson, “Identification of cancer/testis-antigen genes by massively parallel signature sequencing,” Proc. Natl. Acad. Sci. U.S.A., 102 (22), 7940 –7945 (2005). 0027-8424 Google Scholar


G. A. Stolovitzky, A. Kundaje, G. A. Held, K. H. Duggar, C. Haundenschild, D. Zhou, T. Vasichek, K. Smith, A. Aderem, and J. Roach, “Statistical analysis of MPSS measurements: application to the study of LPS-activated macrophage gene expression,” Proc. Natl. Acad. Sci. U.S.A., 102 (5), 1402 –1407 (2005). 0027-8424 Google Scholar


I. H. White, R. V. Penty, J. Hankey, K. A. Williams, G. F. Roberts, M. Glick, and D. McAuley, “Optical local area networking using CWDM,” Proc. SPIE, 5248 284 –293 (2003). 0277-786X Google Scholar


J. B. Schlager and A. H. Rose, “Annealed optical fiber mode scrambler,” Electron. Lett., 37 (1), 9 –10 (2001). 0013-5194 Google Scholar


L. L. Blyler, L. G. Cohen, G. J. Grimes, and L. J. Haas, “Mode scrambler with noninvasive fabrication in an optical fiber’s cladding,” (1990). Google Scholar


J. Arrue, G. Aldabaldetreku, G. Durana, J. Zubia, I. Garces, and F. Jimenez, “Design of mode scramblers for step-index and graded-index plastic optical fibers,” J. Lightwave Technol., 23 (3), 1253 –1260 (2005). 0733-8724 Google Scholar


J. P. Bristow and J. A. Lehman, “Fiber optic mode scrambler,” (1999). Google Scholar
©(2008) Society of Photo-Optical Instrumentation Engineers (SPIE)
Lianshan Yan, X. Steve Yao, Lynn S. Lin, and Xiaojun Chen "Improved beam uniformity in multimode fibers using piezoelectric-based spatial mode scrambling for medical applications," Optical Engineering 47(9), 090502 (1 September 2008).
Published: 1 September 2008

Back to Top