|
1.IntroductionLiquid crystal optical-phased array (LCOPA) can realize a nonmechanical beam steering by applying the required voltage profile to the phase elements. Compared with the mechanical beam directing systems, it has remarkable advantages, such as low-power consumption, programmability, precise stabilization, low weight, random-access pointing, insensitivity to acceleration, and high-pointing accuracy. Thus, LCOPA has the potential applications in missile interceptors, satellite communications, and laser radar.1–3 In the past decades, LCOPA has received considerable attentions, and the performance has been improved significantly. For example, nonmechanical beam steering over a field of regard had been demonstrated in 2004, and the diffraction efficiency is 15% to 20%.4 By utilizing the lithographic process technique, LCOPA can be integrated on a liquid crystal waveplate. Hence, the pitch between adjacent phase elements (center to center) can be made smaller and smaller, and the pixel pitch for LCOPA had been decreased to 1.6 μm by Boulder Nonlinear Systems.5 The presence of grating lobes in LCOPA will disperse the energy of the output beam and degrade the diffraction efficiency. Unfortunately, the grating lobes are unavoidable for LCOPA due to the limitation of the state-of-art and the wavelength of radiation. Even the pixel pitch mentioned above is not small enough to avoid the grating lobes for LCOPA in the visible or near-IR region, because the required pixel pitch is less than half a micron according to the conventional microwave-phased array theory.6,7 By exploiting the conventional microwave-phased array technique, the grating lobes for optical-phased array are studied.8 This technique can only accurately predict the locations of the grating lobes. However, the intensities of these grating lobes obtained by this technique are the same as that of the main lobe, which is not consistent with the experimental results in practice. In this article, we address the problem of correctly predicting both the locations and the intensities of the grating lobes simultaneously. Specifically, we first introduce the blazed grating models of LCOPA. In fact, when the designed phase profile is applied to LCOPA to steer the incident beam to the desired direction, the LCOPA can be seen as a blazed grating,9 which can be classified into the period blazed grating and nonperiod blazed grating.10,11 The period one is similar to the binary optical elements and can steer the incident beam to some discrete angles. The nonperiod one can realize the uniform, continuous beam scanning in the field-of-view of LCOPA.11 Then, we analyze the far-field intensity distribution after the incident beam transmitting through LCOPA, using the Fraunhofer propagation principle.12,13 We obtain the analytical functions of the far-field intensity distributions as well as the locations and the intensities of the grating lobes for both the models. Finally, we evaluate the performance of the derived functions via computer simulations and experiments. 2.Grating Lobes Analysis for LCOPAThis section is devoted to formulating mathematically the far-field intensity distributions for the period blazed grating and nonperiod blazed grating models of LCOPA, i.e., getting the analytical expressions for each case. 2.1.Period Blazed Grating Model for LCOPAWe consider one-dimensional LCOPA with phase elements, as shown in Fig. 1. Assume that the width of the phase element is small enough, so that each element can be seen as a narrow slit, and the diffraction theory of light can be used to calculate the far-field light distribution. For the case of one-dimension, the Fraunhofer diffraction function can be written as12 where is the electric field component of the output beam, is the electric field distribution on the observation screen (i.e., far-field light distribution), denotes the wave vector, is the wavelength of the incident beam, is the distance between the LCOPA and the observation screen, is the horizontal ordinate of Cartesian coordinate in the plane of LCOPA, and is the horizontal ordinate of Cartesian coordinate in the plane of the observation screen. The thickness of the LCOPA is in the orders of magnitude of micron, so it can be neglected.Assume that the phase elements in the LCOPA are independent, and the incident beam is steered to the deflection angle with respect to the normal direction of LCOPA, namely the point in Fig. 1. Then, the phase retardation difference between adjacent elements in one period can be written as where denotes the period corresponding to the deflection angle . Herein, we set the first phase element to the phase element as a period, and then the phase retardation of each element in the period can be denoted asSuppose the incident beam is plane light with zero initial phase and unit amplitude, the electric field component of the output beam, after the incident beam transmitting through the phase elements in the aforementioned period, can be given by where denotes the width of the phase element. The electric field component of the output beam, after the incident beam transmitting through the entire LCOPA, can be obtained by extending Eq. (4) periodically. For an integer , the extension function can be expressed as where is delta function, which is defined asSubstituting Eq. (3) into Eq. (4) and using Eq. (5), we can obtain where is the convolution operator, namelyCombining Eq. (7) with Eq. (1) and ignoring the constant term, the far-field light distribution on the observation screen can be derived as where is the interaction between periods, one period can be seen as a combining element that is similar to the single physical phase element; is single-slit diffraction; and is multislit interference in one period. Based on Eq. (9), the far-field intensity distribution isBased on Eq. (10), when the denominator of is equal to zero, namely meeting Eq. (11), the grating lobes come into being. To avoid the grating lobes, all angle should meet the following inequality: Using Eq. (2), we get the solution of Eq. (12) in the following form: The laser steered by LCOPA is usually a visible or a near-IR laser, whose wavelength is in the orders of magnitude of micron. As is mentioned in the Sec. 1, the width of the phase element cannot be decreased to less than 1 μm to date; thus, the grating lobes are inevitable for LCOPA. Using Eqs. (2) and (11), we can obtain the locations of the grating lobes Substituting Eq. (14) into Eq. (10), one can get the intensity of the grating lobe It is remarked that the locations of the grating lobes are mainly determined by in Eq. (10), namely the multislit interference in one period; suppressed by in Eq. (10), i.e., the single-slit diffraction, the amplitudes of the grating lobes are less than that of the main lobe. 2.2.Nonperiod Blazed Grating Model for LCOPAThe nonperiod blazed grating model for LCOPA is shown in Fig. 2. Assume that the phase elements in the LCOPA are independent, and the incident beam is plane light with zero initial phase and unit amplitude. When the incident beam is steered to the direction with respect to the normal direction of LCOPA (i.e., the point in Fig. 2), the phase retardation difference between adjacent elements can be written as The electric field component of the output beam, after the incident beam is transmitted through the entire LCOPA, can be expressed as Substituting Eq. (17) into Eq. (1) and using Eq. (16), we get the far-field light distribution on the observation screen (ignoring the constant term) where is single-slit diffraction and is multislit interference. From Eq. (18), the far-field intensity distribution can be derived asBased on Eq. (19), we can get the same conclusion as that in Sec. 2.1, i.e., the grating lobes are inevitable for LCOPA at present. From Eq. (19), the locations of the grating lobes are determined by (the multislit interference), which is given by Substituting Eq. (20) into Eq. (19), one can get the intensity of the grating lobe . Equation (19) indicates that the intensities of grating lobes are less than that of the main lobe, which is identical to the results obtained by Eq. (10). 3.Computer SimulationsIn this section, we evaluate the performance of the derived solutions Eqs. (10) and (19) in the previous section via computer simulations for both the period and nonperiod blazed grating model. Note that the negative sign of an angle denotes steering the incident beam to the left, and the positive sign of an angle denotes steering the incident beam to the right in the simulations. 3.1.Period Blazed Grating for LCOPAWe first consider the period blazed grating for a 1920-element LCOPA, whose phase element width is 5 μm. The incident beam is plane light with zero initial phase and unit amplitude, whose wavelength is 0.6328 μm. Suppose that the phase period is 16, and the incident beam is steered to the right side of the normal direction of the LCOPA along the propagating direction of incident beam. The normalized far-field intensity distribution of the simulation is shown in Fig. 3. From the figure, we can see that nd, st, 1st, and 2nd orders are the grating lobes and 0th order is the main lobe. When the angle range is limited to [, 20 deg], the normalized far-field intensity distribution calculated by Eq. (10) is shown in Fig. 4. Inspection on the normalized far-field intensity distribution in Figs. 3 and 4 reveals that the intensities of the grating lobes are less than that of the main lobe for the period blazed grating of LCOPA. To compare the simulation results with the theoretical results, the values of the peak points in Figs. 3 and 4 are shown in Table 1. Table 1Values of the peak points in Figs. 3 and 4.
The angle error is calculated by where is the simulation values of the locations of the main lobe and grating lobes and is the corresponding theoretical values. The intensity error is defined as where is the simulation values of the intensities of the grating lobes and is the corresponding theoretical values.Some observations are now in order from Table 1. First, the locations of the grating lobes of theoretical solution Eq. (14) are identical to these of simulations. Second, the intensity errors of the grating lobes between simulations and the theoretical solution Eq. (15) are less than 0.5%. Consequently, it can be concluded that the simulation results are in an excellent agreement with the theoretical results for period blazed grating of LCOPA. 3.2.Nonperiod Blazed Grating for LCOPAIn this section, we consider the nonperiod blazed grating for a 1920-element LCOPA, whose phase element width is also 5 μm. The incident beam is plane light with zero initial phase and unit amplitude operating at . Assume that the incident beam is steered to the left of 0.5 deg with respect to the normal direction of the LCOPA along the propagating direction of incident beam. Figure 5 depicts the normalized far-field intensity distribution of the simulation. When the angle range is limited to [, 20 deg], the normalized far-field intensity distribution calculated by Eq. (19) is shown in Fig. 6. It can be seen from Figs. 5 and 6 that the intensities of the grating lobes are less than that of the main lobe for the nonperiod blazed grating of LCOPA. To compare the simulation results with the theoretical results, the values of the peak points in Figs. 5 and 6 are shown in Table 2. The angle and intensity errors in Table 2 are calculated by Eqs. (22) and (23), respectively. Some observations are now in order from Table 2. First, the locations of the grating lobes of the theoretical solution in Eq. (20) are identical to simulations. Second, the intensity errors of the grating lobes between simulations and the theoretical solution in Eq. (21) are less than 0.6%. Hence, it can be remarked that the simulation results agree excellently with the theoretical results for nonperiod blazed grating of LCOPA. Table 2Values of the peak points in Figs. 5 and 6.
4.Experimental VerificationsIn this section, we assess the proposed solutions in Eqs. (10) and (19) via experimental data. In Fig. 7, we provide the schematic of experimental setup, which is composed of (1) laser operating at ; (2) diaphragm; (3) 1920-element LCOPA with the element width of 5 μm; (4) controller, applying the voltage code to the LCOPA; (5) PC, generating the voltage code; (6) camera, photographing the diffraction pattern on the observation screen; and (7) observation screen with a distance of 118 cm from the LCOPA. This experimental setup is employed in both period blazed grating and nonperiod blazed grating experiment of LCOPA. 4.1.Period Blazed Grating for LCOPAWe first consider the experiment of period blazed grating based on LCOPA to study the grating lobes. The phase period is 16, which is the same as that in Sec. 3.1. The incident beam was steered to the right of the normal direction of LCOPA along the propagating direction of incident beam. Figure 8 is the far-field intensity distribution observed on the observation screen for the period blazed grating experiment. As shown in Fig. 8, we can observe the main lobe (0th order) and the grating lobes (st and 1st orders) obviously. However, the grating lobes (nd and 2nd orders) are indistinct. The reason is the power of the laser used in the experiment is about 3 mW, so that the grating lobes (nd and 2nd orders) are so weak that the camera can hardly image them. In addition, there are other bright spots between the main lobe and the grating lobes in Fig. 8. The fringing-field effect between adjacent elements in LCOPA is considered to be the main factor that give rise to these unwanted spots, since the fringing-field effect broadens the designed phase profile applied to the LCOPA.14,15 Phase valley and flyback region are other reasons leading to this problem, because they distort the designed phase profile.16,17 The values (including locations and intensities) of the main lobe and grating lobes pointed out in Fig. 8 are shown in Table 3 and are compared with the corresponding theoretical values. The angle error is calculated by where is the experimental values of the locations of the main lobe and the grating lobes and is the corresponding theoretical values, which can be obtained from Table 1. The intensity error is defined as where is the experimental values of intensities of the grating lobes and is the corresponding theoretical values, which can be obtained from Table 1.Table 3Values of the main lobe and the grating lobes in Fig. 8.
Some analyses of Table 3 are in order. First, the angle errors of the locations of the main lobe and the grating lobes between experiment and theoretical solution in Eq. (14) are very small, less than 2.3%. The influencing factors, including measurement error, voltage quantization,18 surface deformation of LCOPA,19 nonuniformity of lead resistance,20 etc., cause the angle error. Second, the intensity errors of the grating lobes between experiment and theoretical solution in Eq. (15) are acceptable, less than 6.3%, caused mainly by the fringing-field effect, flyback region, phase valley, and measurement error. Inspection on the experimental values of intensities in Table 3 reveals that the intensities of the grating lobes are less than that of the main lobe, which confirms the conclusion obtained by Eq. (10). Herein, it can be concluded that the experimental results are in a good agreement with the theoretical results for period blazed grating of LCOPA. 4.2.Nonperiod Blazed Grating for LCOPAIn this section, we consider the experiment of nonperiod blazed grating based on LCOPA. The incident beam is steered to the left of 0.5 deg with respect to the normal direction of the LCOPA along the propagating direction of the incident beam, which is same as in Sec. 3.2. Figure 9 displays the far-field intensity distribution seen on the observation screen for the nonperiod blazed grating experiment. Inspection on Fig. 9 reveals that the main lobe (0th order) and the grating lobes (st and 1st orders) are evident. Because of the low power (3 mW) of the laser used in the experiment, the grating lobes (nd and 2nd orders) are indistinct. There are also some undesired bright spots in Fig. 9. As described in Sec. 4.1, the fringing-field effect and other factors cause these undesired spots. The values (including locations and intensities) of the main lobe and the grating lobes pointed out in Fig. 9 are shown in Table 4 and are compared with the corresponding theoretical values. Table 4Values of the main lobe and the grating lobes in Fig. 9.
The angle and intensity errors in Table 4 are calculated by Eqs. (24) and (25), respectively, and the corresponding theoretical values can be obtained from Table 2. Some analyses of Table 4 are in order. First, the angle errors of the locations of the main lobe and the grating lobes between experimental results and theoretical solutions in Eq. (20) are also very small, less than 2%. The factors causing the angle error are the same as those mentioned in subsection 4.1. Second, the intensity errors of the grating lobes between experimental results and theoretical solutions in Eq. (21) are acceptable, less than 5.6%. The fringing-field effect, measurement error, and other factors cause the intensity error. Based on the experimental values of the intensities in Table 4, one can see the intensities of the grating lobes are less than that of the main lobe, which agrees with the results achieved by Eq. (19). Thus, it can be remarked that the experimental results agree well with the theoretical results for nonperiod blazed grating of LCOPA. 5.ConclusionsIn this article, we have addressed the grating lobes of LCOPA based on the blazed grating theory.
The possible future research track might concern mathematically modeling the unwanted bright spots between the main lobe and the grating lobes. Many factors such as fringing-field effect, phase valley, and flyback region give rise to these spots.14–17 It might be of interest to study effective methods to suppress the grating lobes to a lower level, so as to focus the energy of the output beam to the main lobe. AcknowledgmentsThis work was sponsored by National Natural Science Foundation of China (61178068 and 61201276) and Defense Industrial Technology Development Program (B1120110006). ReferencesP. F. McManamonet al.,
“Optical phased array technology,”
Proc. IEEE, 84
(2), 268
–298
(1996). http://dx.doi.org/10.1109/5.482231 IEEPAD 0018-9219 Google Scholar
P. F. McManamonE. A. Watson,
“Optical beam steering using phased array technology,”
Proc. SPIE, 3131 90
–98
(1997). http://dx.doi.org/10.1117/12.277742 PSISDG 0277-786X Google Scholar
X. Z. WangQ. LiQ. Wang,
“Progress and analysis of the liquid crystal phased array technology in ladar,”
in Proc. RCSLPLT/ASOMT 2010,
273
–276
(2010). Google Scholar
P. F. McManamon,
“An overview of optical phased array technology and status,”
Proc. SPIE, 5947 59470I
(2005). http://dx.doi.org/10.1117/12.631412 PSISDG 0277-786X Google Scholar
A. LinnenbergerS. Serati,
“Advances in optical phased array technology,”
Proc. SPIE, 6304 63040T
(2007). http://dx.doi.org/10.1117/12.679551 PSISDG 0277-786X Google Scholar
Z. S. HeW. Xia, Modern Digital Signal Processing and Application, Tsinghua University Press, Beijing
(2010). Google Scholar
G. Y. Zhang, Principles of Phased Array Radar, National Defense Industry Press, Beijing
(2009). Google Scholar
S. Yinet al.,
“Ultra-fast speed, low grating lobe optical beam scanning using unequally spaced phased array technique,”
Opt. Commun., 270
(1), 41
–46
(2007). http://dx.doi.org/10.1016/j.optcom.2006.11.001 OPCOB8 0030-4018 Google Scholar
R. M. Matic,
“Blazed phase liquid crystal beam steering,”
Proc. SPIE, 2120 194
–205
(1994). http://dx.doi.org/10.1117/12.177691 PSISDG 0277-786X Google Scholar
P. F. McManamonE. A. Watson,
“Design of optical phased array beam steering with limited dispersion,”
in Proc. IEEE,
1583
–1591
(2001). Google Scholar
L. J. Konget al.,
“A beam steering approach of liquid crystal phased array based on non-periodic blazed grating,”
Acta Opt. Sin., 31
(1), 0123001
(2011). GUXUDC 0253-2239 Google Scholar
J. W. Goodman, Introduction to Fourier Optics, Publishing House of Electronics Industry, Beijing
(2011). Google Scholar
D. Y. YuH. Y. Tan, Engineering Optics, China Machine Press, Beijing
(2011). Google Scholar
E. UziA. BorisB. T. Eldad,
“Studies of fringing field effects in liquid crystal beam-steering devices,”
Proc. SPIE, 5936 59360P
(2005). http://dx.doi.org/10.1117/12.618218 PSISDG 0277-786X Google Scholar
X. H. Wanget al.,
“Modeling and design of an optimized liquid-crystal optical phased array,”
J. Appl. Phys., 98
(7), 073101
(2005). http://dx.doi.org/10.1063/1.2071450 JAPIAU 0021-8979 Google Scholar
L. Xuet al.,
“Effect of phase valley on diffraction efficiency of liquid crystal optical phased array,”
Proc. SPIE, 7133 71333L
(2009). http://dx.doi.org/10.1117/12.821247 PSISDG 0277-786X Google Scholar
L. XuZ. Q. Huang,
“Quantitative analysis on flyback region problem of 1D transmissive liquid crystal optical phased array devices,”
Proc. SPIE, 7658 76580N
(2010). http://dx.doi.org/10.1117/12.867702 PSISDG 0277-786X Google Scholar
L. J. Konget al.,
“Research on scanning accuracy of liquid crystal phased array component of laser radar,”
Chin. J. Lasers, 36
(5), 1080
–1085
(2009). http://dx.doi.org/10.3788/JCL ZHJIDO 0258-7025 Google Scholar
B. Wanget al.,
“2-D liquid crystal optical phased array,”
in Proc. IEEE,
905
–912
(2004). Google Scholar
Z. H. LinL. J. KongX. B. Yang,
“The influence factors analysis on the steering performances of liquid crystal optical phased array,”
in Proc. IEEE,
1131
–1134
(2011). Google Scholar
BiographyJian Chen received his BS degree from Southwest University of Science and Technology, Mianyang, Sichuan, China in 2011. Now, he is a PhD student for signal and information processing at University of Electronic Science and Technology of China (UESTC). His research interests are mainly in lidar based on liquid crystal optical-phased array. Guolong Cui received his BS, MS, and PhD degrees from University of Electronic Science and Technology of China (UESTC) in 2005, 2008, and 2012, respectively. He is currently a postdoc in Stevens Institute of Technology, Hoboken, New Jersey. From January 2011 to April 2011, he was a visiting student researcher with University of Naples Federico II, Naples, Italy. His research interests lies in the field of statistical signal processing with emphasis on radar detection and liquid crystal optical-phased array. Lingjiang Kong received his BS, MS, and PhD degrees from University of Electronic Science and Technology of China (UESTC) in 1997, 2000, and 2003, respectively. From September 2009 to March 2010, he was a visiting researcher with the University of Florida, USA. He is currently a professor in the School of Electronic Engineering, UESTC. His research interests are mainly in new type radar system, such as MIMO radar, through the wall radar, statistical signal processing, and liquid crystal optical-phased array. Feng Xiao received his BS in optical engineering from University of Electronic Science and Technology of China (2010). He is now a PHD candidate in school of Electronic Engineering, University of Electronic Science and Technology of China. His major is signal and information processing, and his research interests are mainly about optical phased array technology and radar system. Xin Liu received his MS degree from Dalian University of Technology, Dalian, China in 2008. He is currently a senior engineer at Science and Technology on Electro-Optical Information Security Control Laboratory, Sanhe, China. His current research interests include laser physics and electro-optical information security. |