In the research of modern terahertz (THz) electronics, development of compact, tunable, and coherent sources operating at THz frequencies is one of the hottest issues.1 Two-dimensional (2-D) plasmons in submicron transistors have attracted much attention due to their nature of promoting emission and detection of electromagnetic radiation in the THz range. The channel of a transistor can act as a resonator for plasma waves, the charge-density waves of collectively excited 2-D electrons. The plasma frequency depends on the resonator dimensions and the density of 2-D electrons. It can reach the sub-THz or even THz range for gate lengths of a micron and submicron (nanometer) size. Therefore, different devices/structures of micron and submicron sizes supporting low-dimensional plasmons were intensively studied as possible candidates for solid-state far-infrared (FIR)/THz sources22.214.171.124.126.96.36.199.188.8.131.52.15.16.17.–18 and detectors.19184.108.40.206.220.127.116.11.28.29.–30 Mechanisms of plasma wave excitation/emission can be divided (by convention) into two types: (1) incoherent and (2) coherent. The first is related to thermal excitation of broadband nonresonant plasmons by hot electrons.18.104.22.168.–7 The second is related to the plasma wave instability mechanisms like Dyakonov–Shur (DS) Doppler-shift model8 and/or Ryzhii-Satou-Shur (RSS) transit-time model,17,18 where coherent plasmons can be excited either by hot electrons or by optical phonon emission under near ballistic electron motion.31 On the other hand, hydrodynamic nonlinearities of 2-D plasmons in high-electron-mobility transistors (HEMTs) are promising for fast and sensitive rectification/detection of THz radiation.19 When an incoming THz radiation excites the plasma waves, the local carrier density as well as the local carrier drift velocity is modulated by the radiation frequency. This results in generation of the quadratic current term proportional to the product of the modulated components of the local carrier densities and velocities. The time average of this component is nonzero, leading to rectification. With an asymmetric boundary condition, a rectified component gives rise to a photovoltaic effect. Recently, plasma wave properties were successfully used for the resonant and nonresonant (broadband) sub-THz and THz detection.2021.22.23.24.22.214.171.124.29.–30 They can be applied to real-time THz imaging/spectroscopic analysis as well as future THz wireless communications.1
We have first proposed a 2-D plasmon-resonant microchip emitter featured with an interdigitated dual-grating gates (DGGs) structure.3233.34.–35 The original structure uses symmetrical DGGs in which interfinger spaces are all identical, providing room-temperature 0.5- to 6.5-THz emission with 1-microwat-order radiation power33,34 and rather low detection responsivity of the order of 10’s V/W.35 Recently, authors have proposed an asymmetric DGG (A-DGG) structure and demonstrated coherent monochromatic THz emission and ultrahigh-sensitive THz detection with at 1 THz radiation.3637.38.–39 This paper reviews recent advances in emission and detection of THz radiation using 2-D plasmons in semiconductor nanoheterostructures for nondestructive evaluations. The 2-D plasmon resonance is first presented as the operation principle to demonstrate its potential of broadband intense emission and sensitive detection of THz radiation. Second, the device structure that can provide practical emission and detection performances are addressed, which is based on a HEMT and incorporates the authors’ original asymmetrically interdigitated DGGs. Numerical analysis reveals that in comparison with conventional symmetric DGG (S-DGG) structure, the A-DGG can substantially improve the detection sensitivity as well as the instability (emissivity) by three to four orders of magnitude. Third, excellent THz emission and detection performances including coherent, monochromatic emission beyond 1-THz range39 and an extremely high detection responsivity of at 1 THz at 300 K (Ref. 40) are experimentally demonstrated by using InAlAs/InGaAs/InP heterostructure material systems. Finally, their applications to nondestructive material evaluation based on THz imaging are demonstrated.
THz Emission Using 2-D Plasmons in HEMTs
In a simple case, the 2-D plasma wave motions can be described by the hydrodynamic Euler equation and the continuity equation.81) is the Coulomb force and the second term is the Drude friction. 2-D electron channels in HEMTs consisting of gated and ungated regions as shown in Fig. 1. The ungated 2-D plasmon receives the in-plane longitudinal Coulomb force so that it holds a square-root dispersion relation, which is identical to that for general surface plasmons. The gated 2-D plasmon receives transverse Coulomb force via gate capacitor, which is far stronger than the in-plane force due to the geometrical situation so that it holds a linear dispersion. In a simple case of gradual-channel approximation with infinite channel width (perpendicular to the source-drain direction), the 2-D plasma wave dynamics can be reduced to one-dimensional systems.8 The plasma wave phase velocity is given by , where is the gate swing voltage.19 Assuming and ( is the electron rest mass in vacuum) for InP-based heterostructure HEMTs, becomes , which is at least two orders of magnitude higher than the electron drift velocity of any compound semiconductors with superior transport properties. Thus, when we consider a sub-micrometer gate-length HEMT, the fundamental mode of gated 2-D plasmons stays at a frequency in the THz range. This is the main advantage for use in plasmon-resonant modes that can operate in the frequencies far beyond the transit frequency limit of transistors.
When a single-gate HEMT is situated in source-terminated and drain-opened configuration with dc potential at the drain terminal with respect to the source terminal, the drain end of the channel becomes depleted so that the drain-side impedance is mainly given by the depletion capacitance and takes a high value at high frequencies. In such a case, a Doppler-shift effect occurs on the plasma wave propagation/reflection at the drain boundary, promoting the DS instability.8 Consider the case in which a plasma wave is excited in an HEMT with a constant dc drain bias causing a background constant dc electron drift flow with velocity and the gate length is shorter than the coherent length of electrons. The plasma wave–originated local displacement current is given by the product of the perturbation of the local electron charge density and the plasma wave velocity. The forward (backward) component traveling to (from) the drain boundary is given by . Since the open-drain boundary conserves the current before and after the reflection, , . This increment of the electron charge density directly reflects the increment of the gate potential via gate capacitor . Since the source-terminated boundary gives a lossless reflection (reflection coefficient is ), the gate potential becomes infinite after infinitesimal repetitions of plasma wave reflections, leading to the DS instability. When the plasma wave is excited by the incoming THz radiation with angular frequency , , the effect of the instability is characterized by the imaginary part of , , as
When , the system becomes unstable, giving rise to the condition of the DS instability. The plasma wave increment in units of , a dimensionless plasma wave increment is plotted as a function of the Mach number .8 In reality, with finite value, the Drude loss factor should be considered to obtain an overall gain, which is shown as a threshold level in Fig. 1. So far DS-instability-driven voltage-tunable millimeter-wave to THz-wave emission has been observed at low and room temperatures from GaAs-, InP-, and GaN-based HEMTs.910.11.–12
When the channel pinch-off is insufficient and the drain terminal is not open but yet conductive at THz frequencies, the plasma waves are effectively absorbed in the high-field gate-drain region. Hence their reflection is insufficient to promote necessary positive feedback for the occurrence of the DS instability. At large drain-source voltages, the THz conductivity of this region would be rather high due to the relatively high value of the electron drift velocity in the high-field gate-drain region. In this case, becomes much higher than that in the intrinsic channel region . Note that the electrons propagating in the high-field gate-drain region induce the ac current in the gated channel and the drain contact. One can find that the electron ac concentration as a function of the coordinate varies as .17,18 As a result, the ac current induced in the gated channel is presented. Its frequency dependence is directly reflected by the electron transit time at the gate-drain region , where is the length of the gate-drain region, which may contribute to promote the plasma wave instability.17 In this case, the instability condition is given by the following inequality using the imaginary part of the plasma wave current:17 Here, and are the DS-instability index and the transit-time-driven RSS-instability index, respectively. can take both positive and negative values depending on . The contributions to the plasma wave instability growth rate of the DS and RSS mechanism ( and ) in an HEMT with typical geometric and material parameters are plotted in Fig. 2 as functions of the fundamental plasmon mode frequency.17 Due to the nature of transit-time-driven mechanism, the RSS instability is sensitive to the plasmon mode frequency.
The 2-D plasmon itself is a nonradiative mode so that a metal-wired grating coupler structure is frequently utilized to yield THz electromagnetic-wave emission.126.96.36.199.–7 If the single gate is replaced with a grating-finger-type gate, a plural number of plasmonic cavities (whose electron density is modulated by the bias voltage of the grating-finger gate) are electrostatically coupled (via interfinger region with less electron density) in a spatially distributed configuration. In this case, a constant dc channel current, which is generated by the applied dc drain bias, gives rise to periodic electron velocity modulation over the channel. This may also promote the RSS instability.18
In particular, the DGG structure provides an improved confinement of the 2-D electrons into the plasmon cavities independent of the tuned gate biases, resulting in more intense resonant plasma excitation with higher quality factors [see Fig. 3(a)].3233.–34 The DGGs can alternately modulate the 2-D electron densities to periodically distribute the plasmonic cavities ( width in microns distance) along the channel by applying a large fraction of gate biases for subgratings G1 and G2.3233.–34 Under pertinent drain-source dc bias conditions, dc electron drift flows may promote the plasmon instability, resulting in self-oscillation with characteristic frequencies in the THz regime. Figure 3(b) depicts the potential distribution and equivalent circuit model for the RSS instability under a constant dc-drain bias condition. The 2-D electron channel consists of a periodic series of highly confined 2-D plasmon cavity sections underneath the gate finger G1 and a depleted section underneath the gate finger G2.
According to the aforementioned RSS instability mechanism, the depleted barrier section works for the negative conductance gain section, whereas the highly confined section works for the plasmonic resonator modeled by an circuitry as shown in Fig. 3(b).38 The model accounts for the features of the electron transport across the device structure with the 2D-electron stripes (2DESs) that are formed underneath one grating gate fingers separated by the depleted barrier regions and the possibility of the plasma oscillations in the 2DESs electrically coupled via the barrier regions. We demonstrated that, due to the negative dynamic conductance of the barrier regions associated with the electron transit-time effects, the plasma instability leading to the self-excitation of the plasma oscillations (and the emission of THz radiation) becomes feasible when the dc current exceeds a certain threshold value.33
We have proposed our original DGG-HEMT-type 2-D plasmon-resonant microchip emitter as a new THz light source.3233.–34,39 The original structure is a S-DGG in which interfinger spaces are all identical. The device was fabricated using InGaP/InGaAs/GaAs and/or InAl/InGaAs/InP material systems.33,34 So far a broadband THz emission ranging from 1 to with a maximum output power of at 300 K has been obtained reflecting multimode of coherent/incoherent plasmons,41 for which oblique modes,42 gated and ungated plasmon modes,43 hot plasmons,41 and chirped plasmon modes33 are the major causes. The DGG-HEMT THz emitter can work for THz spectroscopic and imaging applications as an incoherent broadband THz microchip source, demonstrating fine identification of water vapor absorptions as well as finger prints of sugar groups.34
In order to realize coherent monochromatic THz emission, we introduced our original A-DGG structure [Figs. 4(a) and 4(b)].36 In the A-DGG structure, the DGG is implemented with asymmetric interfinger spaces. THz electric field distribution and resultant photoresponse were numerically simulated using a self-consistent electromagnetic approach combined with the perturbation theory for the hydrodynamic equations for 2-D plasmons in HEMTs under periodic electron density modulation conditions [Figs. 4(c) and 4(d)].36,39 Figure 4(c) shows giant enhancement of the responsiveness (by four orders of magnitude) in an A-DGG HEMT under drain-unbiased conditions with respect to that for a S-DGG HEMT for a dc drain bias current density of . When the A-DGG HEMT is dc-drain biased, the asymmetry of the plasmonic cavity is enhanced enormously, resulting in further enhancement of the responsiveness by orders of magnitude. It is reasonable to suggest that a similar enhancement should also be exhibited for the plasmon instability in the A-DGG HEMT. A chirped DGG structure was also introduced so as to uniform the plasmon frequencies over the entire DGG area under a specific drain-source bias condition. These two features are combined to serve an asymmetric chirped DGG (AC-DGG) structure. Moreover, a high-Q vertical photonic cavity structure is installed to stimulate the resonant-enhanced coherent plasmon excitation.32,39
AC-DGG HEMTs were designed and fabricated using InAlAs/InGaAs/InP materials [see Fig. 4(b)]. Two grating gates G1 and G2 were formed with 70-nm-thick Ti/Au/Ti by a standard lift-off process. An asymmetric factor, the ratio of the interfinger spaces, , was fixed to be 0.5. The grating gates G1 with narrower fingers , serving plasmon cavity gates, were designed to be chirped ranging from 215 to 430 nm. The design parameters are summarized in Table 1. After processing the AC-DGG HEMT, a high-Q vertical cavity with a high finess of was formed with a 4.4-μm-thick transparent PW1500 resist as a low-loss buffer layer and a 70-nm-thick indium tin oxide (ITO) mirror coat on top and a 100-nm Ti/Au coat on the polished back surface [see Fig. 4(b)]. Its fundamental resonant frequency (free spectral range of the Fabry-Perot modes) was designed to be 65 GHz.
Design parameters of fabricated devices.
|Cavityc||Lo Q||High Q||Lo Q||High Q|
|FSR||145 GHz||65 GHz||65 GHz||65 GHz|
|# of fingers G1/G2||37/38||30/31||30/31||8/9|
|Active area (μm2)||75×75||30×75||30×75||20×20|
x=0.53/0.7/0.53 (composite channel)
S: Symmetric, AC: Asymmetric and chirpad
Lo Q: Au mirror coat on back surface only
The fabricated HEMTs exhibit normal dc transfer characteristics with good pinch-off and gate modulations for both G1 and G2 with threshold levels of and , respectively. We conducted THz spectroscopic measurements for the fabricated devices using a Fourier-transform far-infrared (FTIR) spectrometer and a 4.2-K-cooled Si composite bolometer. The gate bias for the plasmon cavities was fixed at 0 V. Material- and structure-dependent emission spectra at 290 K are plotted in Fig. 5(a) in comparison with previously reported GaAs-based and InP-based S-DGG HEMTs.39 The drain bias was set so as to equal the voltage drop along a unit DGG section among all the devices. All three S-DGG HEMTs SG1, SG2, and SP1 exhibit weak Fabry-Perot-modes emission and intense broadband emission as a background originated from the thermal excitation of broadband nonresonant plasmons by hot electrons.188.8.131.52.–7 On the contrary, superiorities of the A-DGG structure and InP-based materials with higher electron mobility result in intense Fabry-Perot-modes emission and weakened background emission. The identification of the plasmon modes in the emission spectra is based on (1) designed structure dimensions and material properties that determine the mode frequencies, and (2) dependence of the spectral peak intensity on . If the frequency of a spike in the emission spectrum corresponds to a plasmon resonant mode, its peak intensity will increase with increasing , thus promoting the instability. 2-D electron density distribution is modulated by ; the plasmon mode frequencies become slightly lower with increasing . This mode-frequency shift might mask the increase in peak intensity if the mode frequency is detuned from the Fabry-Perot mode. The fundamental plasmon mode of the device ACP1 has a frequency of . From the observed emission spectra, the first, third, and fifth modes could be identified as designated with arrows in Figs. 5(b) and 5(c). The highest peak intensity is observed at with a sharp linewidth of () corresponding to the fifth plasmon mode. Figure 5(b) plots the dependence of the emission spectra on under an optimal condition ().39,44 When decreases from 1.0 to 0.4 V, both DS and RSS instabilities are weakened so that the stimulated coherent emission is suppressed. This may increase the hot plasmon–originated spontaneous broadband emission and thus the monochromaticity on emission spectra is degraded. When the temperature cools down to 190 K, hot plasmons–originated residual spurious modes are suppressed, resulting in intense monochromatic emission at the first (at 1.2 THz) and third (at 3.6 THz) plasmon modes whose frequencies match to adjacent Fabry-Perot modes, respectively, as shown in Fig. 5(b). The emission peak at the fifth (at 6.1 THz) plasmon mode disappears, which is considered to be caused by the temperature dependence of the 2-D electron density in the plasmon cavities reflecting frequency detuning of the plasmon modes. Simulated time evolution of the instantaneous electric field () distributions under a constant sinusoidal plasmon excitation at 3.6 THz assures the cooperative oscillation of all the plasmon cavities underneath the subgrating finger G1 as shown in Fig. 5(c), supporting the superradiant THz emission. The output power of sample ACP1 is estimated to be of the order of 0.1 to 1 μW.
THz Detection Using 2-D Plasmons in HEMTs
Detection of THz radiation by plasmonic nonlinearities in a 2-D electron channel of a field-effect transistor (FET) was originally proposed by Dyakonov and Shur.19 Resonant (frequency selective)20,21,2425.–26 as well as nonresonant (broadband)22,23,26 plasmonic detectors have been studied. The frequencies of the plasmon resonances in the FET channel with asymmetric boundary conditions are given by19
The hydrodynamic motion of the plasma wave kinetics yields a nonlinear plasma wave current component as the product of the local electron density and local electron velocity, both of which are perturbed by incoming THz radiation, giving rise to a quadratic rectification component in the current time-integral as shown in Fig. 6. This is the fundamental principle of the THz detection using the plasma wave dynamics.19,22 In the open circuit condition, the generated (rectified) photocurrent is transformed to a dc voltage component leading to photovoltaic signal . By solving Eqs. (1) and (2) under pertinent source-terminated and drain-opened boundary conditions, is derived as follows:19
As is mentioned in Sec. 2.2, we propose an A-DGG structure as shown in Fig. 4, which also provides ultrahigh-sensitive THz detection.3738.39.–40 This is because the unit cell of the A-DGG structure can create a strong built-in asymmetric field. The THz photoresponse dramatically increases when the parts of the 2-D channel under the fingers of one of the two subgratings are depleted.
The A-DGG structure can greatly enhance the asymmetry of the cavity boundaries by applying different gate voltages and to the two different subgratings of the A-DGG. Due to the asymmetry, the impedances at both ends from the 2-D plasmon cavity are different. Thus, the photocurrent generated in 2-D plasmon by the THz radiation performs unilateral transport, resulting in high photovoltaic signal at each cell. These signals at every 2-D plasmon cavities are summed up, leading to an effective photovoltaic signal between the drain and source.37
The device under characterization is identical to the InAlAs/InGaAs/InP A-DGG HEMTs shown in Fig. 4 except for the lack of a vertical cavity [seen in the lower right panel of Fig. 4(b)]. The A-DGG HEMTs have been designed and fabricated using InAlAs/InGaAs/InP material system.37 The geometrical parameters of the A-DGG HEMTs are summarized in Table 2. Room temperature THz photovoltaic measurements were conducted with fabricated devices. The devices exhibit normal gate modulation operation on their drain-source current-voltage characteristics.37 For G1 and G2, the threshold voltage and are and , respectively.
Design parameters of fabricated A-DGG HEMTs.
|# of fingers G1/G2||8/9||8/9||6/7|
x=0.53/0.7/0.53 (composite channel)
AC: Asymmetric and chirpad
Note: Lg2 and active area are fixed to be 1600 nm and 20×20 μm2
We conducted room temperature THz photovoltaic measurements with the fabricated detectors. Monochromatic THz pulsed waves with frequencies from 1 to 3 THz from a ring-cavity THz parametric oscillator source are focused on the detector by a Tsurupica™ lens.3738.39.–40 The photovoltaic signal was observed as a fluctuation with a lock-in technique. The responsivity was estimated as , where is the THz-radiation-induced dc drain voltage, is the total power of the source on the detector plane, is the radiation beam spot area, and is the active area of the detector. Figure 7(a) shows the measured responsivity of detector # 2-4 at 1 THz under zero- condition as a function of gate voltage swing (); dc voltage of G1: (G2: ) is swept, while () is floated (biased at 0 V).37 The best result with was obtained when sweeping to the threshold .37,38 It should be noted that even at higher frequencies, relatively high responses are obtained with detectors # 2-3 having a shorter . As seen in the inset of Fig. 7(a), the responsness monotonically decreases from at 1 THz to at 2 THz. All these values are, to the best of the authors’ knowledge, the best ever reported at these frequencies. Figure 7(b) shows the measured responsiveness of detector # 2-3 at 1.5 THz under -biased conditions. On increasing from 0 to 0.4 V, the maximum responsiveness increases to , which is, to the best of the authors’ knowledge, the record responsiveness of fast-response detectors at 300 K.40 The photovoltaic signal increases on decreasing the gate bias and takes a peak value when the gate bias is approaching the threshold level for all the photoresponses. It is expected to turn down and drop when the gate bias decreases to the subthreshold region as was measured for S-DGG HEMTs35 as well as standard single-gate HEMTs.22 Very recently, a physical model that explains this photoresponse dependence on gate bias has been developed.45
Figure 8 shows noise equivalent power (NEP) for detectors (a) # 2-4 and (b) # 2-3, as a function of under drain-unbiased condition.37 The detector # 2-3 exhibits extremely low NEP with the minimal value at 1 THz. These values are lower than those of commercial room temperature THz detectors such as Golay cells () (Ref. 46) or Schottky barrier diodes ().36 The NEP value is proportional to the square root of the drain resistance and the inverse responsivity . On decreasing the gate swing voltage (), the responsivity becomes larger in the range (see Fig. 8), resulting in the decrease of the NEP value. On the other hand, near the threshold condition , the drain resistance becomes much larger because of the pinch-off, resulting in an increase of the NEP value. As a result, the NEP value becomes minimal around the midpoint (. This trend is seen for all the A-DGG HEMT devices and bias conditions due to very similar characteristics of drain resistance and responsiveness for both gates at every frequency measured.
The detection performance at a low frequency of 292 GHz was also characterized at low temperatures ranging from 50 to 125 K (see Fig. 9).44 By decreasing the temperature, one can see a peak appearing as a shoulder and narrowing on the detection curves. This peak is identified as a gated plasmon resonance and its frequency can be estimated as , where is the incident frequency and . This width is found to vary from 279 to 100 GHz when decreasing the temperature. The observed shrinking of the resonance peak can be explained by an increase of plasma waves damping time via an increase of carrier’s mobility. The quality factor of the resonances’ linewidth is experimentally determined by from which the plasmon decay time is estimated to be . This quality factor should reflect on the response speed of the plasmon-resonant. Therefore, very fast speed THz detection beyond tens of Gbit/s could be feasible. Its precise characterization is a future subject of study. The device response speed is characterized indirectly by the resonant-mode detection. Figure 9 also shows calculations of channel resistivity and the difference induced in drain current by the incoming THz radiation (I with radiation—I without radiation). The curves (right axis) consistently shows the resonant peak obtained from experiments.
Utilizing the excitation of 2-D plasmons is a promising approach for both emission and detection of THz radiation. Recently, there were several outstanding works published on THz plasmonic detection by nanowire single-gate FETs47 as well as graphene-channel single-gate FETs.48 A comprehensive review of all these single-gate plasmonic nanotransistor detectors is given in a recent paper by Knap et al.49 The DGG HEMT detectors can potentially offer better figures of merit because of their following important advantages against all these single-gate FET detectors.
1. The DGG-HEMT THz detector does not need supplementary antenna elements because the grating gate itself serves as an effective coupler between THz radiation and plasmons in the HEMT channel. On the contrary, a single-gate plasmonic FET weakly couples to THz radiation and hence needs supplementary antenna elements.
2. Asymmetry needed for obtaining strong detection signal is introduced into each unit cell of the DGG structure in a controlled way by using monolithically integrated technology. Therefore, all unit cells operate coherently, yielding the strong cumulative resultant detection response.
3. The DGG-HEMT combines useful properties of both resonant and nonresonant THz plasmonic detectors. Plasmons (also nonresonant plasmons) are effectively excited in undepleted portions of the entire DGG-HEMT channel, while strongly depleted (hence highly resistive) portions of the DGG-HEMT channel under the biased subgrating of the DGG serve for effective readout of the photovoltaic detection signal.
All these advantageous features combined together result in a huge THz photovoltaic response of the DGG-HEMT detectors as mentioned above.
Applications to Nondestructive THz Spectroscopy
2-D Plasmon Emitters for Broadband THz Light Sources in Fourier Transform THz Spectroscopy
The plasmon resonant A-DGG-HEMT emitter SG-1 shown in Fig. 5(a) was introduced into the FTIR system in place of the mercury lamp and its applicability as a broadband THz light source was examined. The detector was a 4.2-K-cooled Si composite bolometer whose absolute detection power was not calibrated so that we could characterize the relative intensity spectra. Atmospheric water vapor and several sugar groups, whose identical absorption/transmission spectra coexist in the emission spectral range available from the emitter, are chosen as samples under measurement. First, the atmospheric water-vapor absorption was measured. The experimental procedure was as follows: first, we measured the emission spectra in vacuum inside the spectrometer as the reference. Then, the atmospheric air was introduced into the spectrometer and we performed the actual measurement. The obtained result was normalized to the reference data. The FTIR system (Fig. 10) shows the measured absorption spectrum of the water vapor. The result ranging from 1 to 6.5 THz coincides well with the spectrum data provided by NASA.34
Next, we measured the transmission spectra of two different types of sugar groups: honey and maple syrup, both of which contain featured spectrum in the THz region. Figures 11(a) and 11(b) plot the results measured by using the plasmon-resonant emitter (this work) and by using a high-pressure mercury lump, and their main component(s) provided by RIKEN.34 The measured samples—honey and maple syrup—were in liquid form, but the components of sugar groups measured by RIKEN were dry pellets. Thus, comparison of the absorption peak points among them does not make sense. However, the molecular structures may reflect on the overall spectral shape. They clearly exhibit identical spectral features for both materials. The major bumps measured for each spectrum correspond fairly well to those for the main components for each: (a) honey versus glucose and fructose and (b) maple syrup versus sucrose. Other minor part of the ingredients and/or impurities may also perturb the spectral shape. Compared with a high-power mercury lamp, the plasmon-resonant microchip emitter yields higher noise on the spectra due to weak emission intensity. Further improvements on its emission power will be feasible as is described before, which enables the device to be a promising candidate as a new THz light source.
2-D Plasmon Detectors for THz Imaging
A THz imaging experiment was carried out for several DGG HEMT detectors using the experimental setup shown in Figs. 12(a) (Ref. 38) and 12(b) (Ref. 39). The imaging results are shown in Figs. 12(c) (Ref. 38) and 12(d) (Ref. 39). The samples under imaging are (c) a tea bag with an aluminum-coated plastic package (a 50-nm-thick aluminum being vacuum-evaporated onto the plastic film) and (d) an IC card and a soap bar. As seen in Fig. 12(c), the THz radiation can transit through the aluminum-coated plastic package so that it could successfully identify the contents of the tea leaves inside the tea bag. As seen in Fig. 12(d), measured results clearly demonstrate the imaging of hidden substances of circuit/antenna components inside of the IC card and the thickness of the soap bar with a nice contrast in a sub-mm resolution.
Recent advances in emission and detection of THz radiation using 2-D plasmons in semiconductor nanoheterostructures for nondestructive evaluations were reviewed. The Doppler-shift effect of the plasma wave velocity under an asymmetric plasmon cavity boundary and/or the spatial modulation of electron transit time in a sub-micrometer scale 2-D plasmon system with a nonuniform 2-D electron density distribution can promote the plasmon instability, resulting in self-oscillation of plasmons in the THz regime. The hydrodynamic nonlinearity of 2-D plasmons can rectify the incoming electromagnetic radiation, resulting in photovoltaic detection of THz radiation under an asymmetric 2-D plasmon cavity boundary. The device structure that can provide practical emission and detection performances was addressed and was based on an HEMT that incorporated an asymmetrically interdigitated DGGs structure. Excellent THz emission and detection performances including coherent, monochromatic emission beyond 1-THz range and an extremely high detection responsiveness of at 1 THz at 300 K were experimentally demonstrated by using InAlAs/InGaAs/InP heterostructure material systems. Finally, several applications to nondestructive material evaluation based on THz imaging are demonstrated. The obtained results encourage us to proceed with further industrialization of these plasmonic THz devices.
The authors are grateful to M. Dyakonov, M. S. Shur, and S. A. Nikitov for valuable comments. This work has been supported by the JST-ANR Japan-France International Strategic Collaborative Research Program “Wireless communication using terahertz plasmonic nano ICT devices,” the JSPS-RFBR Japan-Russian Joint Research Program, the Russian Foundation for Basic Research (Grant # 11-02-92101, 12-02-93105, and 13-02-12070), and the Russian Academy of Sciences Program “Fundamentals of Nanostructure Technologies and Nanomaterials.” The work was performed under the umbrella of the GDR-I project “Semiconductor sources and detectors for terahertz frequencies.”
Taiichi Otsuji received his BS and MS degrees in electronic engineering from Kyushu Institute of Technology, Fukuoka, Japan, in 1982 and 1984, respectively, and his PhD degree in electronic engineering from Tokyo Institute of Technology, Tokyo, Japan, in 1994. From 1984 to 1999, he worked for NTT Laboratories, Kanagawa, Japan. In 1999, he joined Kyushu Institute of Technology as an associate professor, becoming a professor in 2002. Since 2005, he has been a professor at the Research Institute of Electrical Communication, Tohoku University, Sendai, Japan. His current research interests include terahertz electronic and photonic materials/devices and their applications. He is authored and coauthored more than 170 peer-reviewed journals. He is a senior member of the Institute of Electrical and Electronic Engineers (IEEE) and the Optical Society of America, and a member of the Institute of Electronics, Information, and Communication Engineers of Japan and the Japan Society of Applied Physics (JSAP). He was the recipient of the Outstanding Paper Award of the 1997 IEEE GaAs IC Symposium and has been awarded the IEEE Electron Device Society Distinguished Lecturer since 2013.
Takayuki Watanabe received his BE and ME degrees in electrical communication engineering from Tohoku University, Sendai, Japan, in 2009 and 2011, respectively. He is presently with the Research Institute of Electrical Communication, Tohoku University, Sendai, Japan and is working toward the Dr. Eng. degree. He is a student member of the JSAP.
Stephane Albon Boubanga Tombet received his MS and PhD degrees in condensed matter physics from Montpellier 2 University in France in 2005 and 2008, respectively. From 2008 to 2009, he worked for Montpellier 2 University as a teacher and research assistant. From 2009 to 2011, he joined the Research Institute of Electrical Communication, Tohoku University, Sendai, as a postdoctoral researcher granted by the Japanese Society for the Promotion of Science (JSPS) for one year fellowship. Since 2012, he is working as a postdoctoral researcher at Los Alamos National Labs in New Mexico. His current research interests include terahertz electronic and photonic materials/devices and their applications. He has authored and coauthored more than 20 peer-reviewed journals.
Akira Satou received his BS, MS, and doctor of computer science degrees from University of Aizu, Japan, in 2003, 2005, and 2008, respectively. He was a research fellow of JSPS in 2006 and 2007. He was an assistant lecturer at Information Systems and Technology Center and Research Center for Advanced Information Science and Technology, University of Aizu in 2008 and 2009, respectively. Since 2010, he has been an assistant professor at Research Institute of Electrical Communication, Tohoku University, Japan. His research activity is associated with theoretical study and computer simulation of carrier transport in semiconductor nanostructures, including heterostructure two-dimensional electron gas and graphene, for terahertz applications. He is the author and coauthor of 40 papers in refereed journals. He is a member of the American Physical Society (APS) and IEEE. He received Young Researcher Award at the 1st International Symposium on Terahertz Nanoscience in 2011.
Victor Ryzhii obtained his PhD and Dr.Sc. (habilitation) degrees from Moscow Institute of Physics and Technology, Russia, in 1970 and 1975, respectively. From 1970 to 1993, he worked in academical and industrial institutions in Russia. In 1993, he joined the University of Aizu, Japan, where he worked as a professor until 2012. Currently, he is a professor emeritus of the University of Aizu and a visiting professor of the Research Institute of Electrical Communication, Tohoku University, Japan. His research activity is associated with physics and computer modeling of low-dimensional semiconductor heterostructures and electronic, optoelectronic, and terahertz devices based on nanostructures, including graphene-based devices. He has about 300 journal publications, numerous conference papers, and 11 patents. He is a fellow of IEEE, APS, and the Institute of Electrical and Electronics Engineers, Japan, a corresponding member of the Russian Academy of Sciences, and a member of the JSAP.
Vyacheslav Popov received the Candidate of Science and Dr.Sc. degrees in radiophysics from Saratov State University, Russia, in 1984 and 1999, respectively. During 1985 to 1990, he worked as an academic secretary at Regional Council of the Russian Academy of Sciences in Saratov, Russia. Since 1990, he has held a position of head of Advanced Studies Department at Saratov Research Center of the Russian Academy of Sciences. In 1999, he joined Kotelnikov Institute of Radio Engineering and Electronics of the Russian Academy of Sciences, where he is currently the head of Photonics Laboratory. Since 1999, he is a professor at Physics Department of Saratov State University. He has published more than 100 papers in peer-reviewed journals in the field of theory and modeling of electromagnetic phenomena in microelectronic and nanoelectronic devices.
Wojciech Knap obtained his master’s degree from the Faculty of Physics, Warsaw University Poland and got a permanent assistant professor position in the Experimental Solid State Physics Department. His PhD concerned the terahertz (far-infrared) properties of narrow gap semiconductors HgTe and InSb. In 1987, he left to France and worked at University of Montpellier, Grenoble High Magnetic Field Laboratory, Toulouse Pulsed High Magnetic Field Laboratory. In 1992, he obtained a permanent position at French National Center for Scientific Research, Montpellier, where he works now. Between 1999 and 2001, he worked (sabbatical) at USA—Rensselaer Polytechnic Institute. He also obtained a long-term grant from Japan Society of Promotion of Science and spent a year at Tohoku University (2007 to 2008). His main scientific interests are (1) far-infrared (terahertz) properties of semiconductors, (2) quantum phenomena in transport, and (3) terahertz plasma excitations in low-dimensional structures.