31 December 2013 Concepts, performance review, and prospects of table-top, few-cycle optical parametric chirped-pulse amplification
Author Affiliations +
More than 20 years after the first presentation of optical parametric chirped-pulse amplification (OPCPA), the technology has matured as a powerful technique to produce high-intensity, few-cycle, and ultrashort laser pulses. The output characteristics of these systems cover a wide range of center wavelengths, pulse energies, and average powers. The current record performance of table-top, few-cycle OPCPA systems are 16 TW peak power and 22 W average power, which show that OPCPA is able to directly compete with Ti:sapphire chirped-pulse amplification-based systems as source for intense optical pulses. Here, we review the concepts of OPCPA and present the current state-of-the art performance level for several systems reported in the literature. To date, the performance of these systems is most generally limited by the employed pump laser. Thus, we present a comprehensive review on the recent progress in high-energy, high-average-power, picosecond laser systems, which provide improved performance relative to OPCPA pump lasers employed to date. From here, the impact of these novel pump lasers on table-top, few-cycle OPCPA is detailed and the prospects for next-generation OPCPA systems are discussed.



Ultrafast laser amplification was revolutionized in 1985 when chirped-pulse amplification (CPA) was introduced.1 In CPA, the low-energy sub-1-ps pulses from an ultrafast oscillator are stretched in time to several hundred picoseconds or few nanoseconds. The energy of these pulses is increased in consecutive amplifier stages to the millijoule- (mJ) or even joule-level, while the peak power remains below the threshold of optical damage and pulse distortion in the amplifiers. After amplification, these pulses are recompressed to almost the original pulse duration, allowing to obtain ultrafast pulses with terawatt (TW) peak powers.2 Countless major and minor improvements on Ti:sapphire-based CPA have been reported over the last three decades. To date, table-top, high-peak-power systems exceeding 100 TW operate in laboratories around the world and are commercially available. As a result, Ti:sapphire-based CPA systems are currently the dominant driving lasers for ultrafast, high-intensity experiments.

Further increases in performance have been challenging due to two effects. First, the amplification bandwidth of Ti:sapphire systems is limited to 75nm (FWHM) centered at 800 nm, and gain narrowing associated with amplification over several orders of magnitude further narrows the obtainable bandwidth. Thus, this effect must be compensated for in order to obtain sub-35-fs pulse duration from TW-scale systems. Spectral filtering techniques can be employed to enable compressed pulse durations as short as 15 to 30 fs depending on the level of amplification.3 On the other hand, nonlinear propagation methods can be utilized to convert a portion of the output of these CPA systems to durations in the few-cycle pulse regime. Such schemes, including spectral broadening in hollow-core fibers45.6 and filamentation-based self-compression,78.9 have been employed to shorten the pulses to quasi-single-cycle duration with up to several mJ-level pulse energies resulting in peak powers at the 1 TW-level. The second limiting effect in Ti:sapphire CPA systems prohibits the output average power to be scaled beyond 30 to 40 W with cryogenically cooled amplifier stages.10 Compensation of thermal effects and beam distortions become increasingly challenging at this performance level. High repetition rate systems have been presented operating with high average power, such as a system providing 26 W compressed with duration of >50fs.11

Extending the concept of CPA, the method optical parametric chirped-pulse amplification (OPCPA) was first presented in 1992.12 Similar to CPA, an ultrashort pulse is first stretched in time, amplified, and recompressed. In contrast to CPA, in which amplification is based on stimulated emission, OPCPA transfers energy from a pump beam to a seed beam in an optical parametric amplifier (OPA). The amplification bandwidth can span almost one octave supporting sub-10-fs pulse durations in the visible spectrum. These pulses are referred to as optical few-cycle pulses since their durations approach the duration of an optical cycle (2.66 fs at 800 nm wavelength). In contrast to traditional amplification via stimulated emission in pumped laser crystals, no energy is directly stored during the amplification process in the nonlinear material due to the instantaneous nature of the OPA process, thereby mitigating typical thermal effects and beam distortions, thereby facilitating power and energy scaling of the OPA systems. The pulses from table-top OPCPA systems have been compressed to the few-cycle regime, with the nominal current record durations of 5.0 fs (1.7 cycles) at 0.88 μm,13 10.5 fs (1.5 cycles) at 2.1 μm,14 67 fs (6.3 cycles) at 3.2 μm,15 and 83 fs (6.4 cycles) at 3.9 μm.16 As will be discussed later, table-top OPCPA systems are primarily limited in terms of pulse energy and average power by the employed pump laser; however, onset of parasitic effects have been reported and will be discussed in Sec. 2.4. The records in terms of peak power [16 TW (Ref. 17)] and average power [22 W (Ref. 13)] indicate that the OPCPA method has matured to a performance level comparable to Ti:sapphire-based CPA systems, with the advantage of shorter pulse durations and wavelength tunability from the visible to mid-IR range.

Here, we give a detailed review of the current performance level and the prospects of table-top, few-cycle OPCPA systems based upon recent developments in table-top, high-energy, high-average-power picosecond laser systems. References 18, 19, and 20 provide excellent overviews on the traditional OPCPA architecture, while the OPA process itself has been reviewed comprehensively in Ref. 21, and essential parameters based on simulations for visible OPCPA based upon beta barium borate (β-BaB2O4; commonly referred to as BBO) crystals are presented in Ref. 22. Since the focus in this article is on the recent developments in table-top, few-cycle OPCPA, we intentionally disregard large-scale, petawatt- (PW) level OPCPA laser systems. A few example articles for further reading on PW-scale OPCPA systems include a prospective view in Ref. 23 and a presentation of a full system providing 300 TW in Ref. 24, while Refs. 25, 26, and 27 describe relevant PW-level OPCPA designs.


Table-Top, Few-Cycle OPCPA Systems

Several relevant concepts and trends in OPCPA are reviewed in the following sections, starting with an overview on the early pioneering work toward the generation of few-cycle pulses via OPA and OPCPA. The second section introduces the advantages, challenges, and limitations of few-cycle OPCPA, followed by a section highlighting the record performance levels demonstrated to date. The section concludes with a detailed discussion of the performance of representative OPCPA systems and their pump lasers.


Pioneering Few-Cycle Optical Parametric Amplification

The OPCPA method was first presented in 1992 by Dubietis et al. with a system incorporating a stretcher, an OPA stage, and a compressor, resulting in energetic 70-fs pulses.12 This development was followed rapidly with ground-breaking investigations toward the generation of intense few-cycle pulses. The pioneering work of Gale et al. in 1995 resulted in the presentation of the shortest pulse duration from a laser oscillator at this time with 13 fs and nanojoule-level pulse energy.28 The authors also demonstrated the tunability of the sub-20-fs pulses from the megahertz optical parametric oscillator over a range from 590 to 666 nm center wavelength (see also Ref. 29). Hereafter, several groups investigated few-cycle OPA systems based upon BBO pumped by Ti:sapphire CPA systems enabling the generation of intense sub-10-fs pulses with wide tunability. In 1998, Nisoli et al. employed two OPA stages in collinear configuration to generate 10-μJ-level pulses with 14.5 fs in the near-IR (center wavelength of 1.5 μm),30 and Cerullo et al. used a noncollinear configuration to generate visible sub-8-fs pulses with 2 μJ energy and bandwidth ranging from 510 to 800 nm.31 In the same period, Wilhelm et al.32 in 1997 and Riedle et al.33 in 2000 reported 10-μJ-level, sub-20-fs pulses tunable from 470 to 750 nm and 870 to 1500 nm, respectively. Shirakawa et al. reported in 1998 on a compact noncollinear optical parametric amplification (NOPA) system amplifying pulses with 5 μJ pulse energy and 6.2 fs duration at 630 nm or 8.4 fs at 1.1 μm, respectively,34 and Kobayashi and Shirakawa presented in 2000 sub-5-fs pulses.35 Further improvements on the latter system by Baltuška et al. in 2002 including an ultrashort, white-light, seed pulse and an adaptive pulse compressor enabled the generation of sub-4-fs pulses with 0.5 μJ pulse energy.36 Since most of these pioneering few-cycle OPA implementations were driven by Ti:sapphire-based CPA systems with mJ-level pulse energy and kilohertz repetition rate, the generated few-cycle pulses were limited to the 100 μJ and 0.1 W average power-level. However, the impressive results in the late 1990s demonstrated the potential of energetic few-cycle pulses from OPA (Ref. 21) and lead to the development of few-cycle OPCPA systems driven by a variety of laser technologies, as shown in Sec. 2.6.


Optical Parametric Chirped-Pulse Amplification

NOPA is capable of supporting the amplification of an almost-octave spanning bandwidth. Several parameters are critical in this process: nonlinear medium, phase-matching conditions, input angle, wavelengths, crystal thickness, and pump intensity. A schematic of the geometry is shown in Fig. 1(a) and a photograph of a laboratory implementation is shown in Fig. 1(b).

Fig. 1

(a) Schematic of the noncollinear optical parametric amplification (NOPA) geometry showing the geometry for pump, signal, and idler beam. (b) Laboratory picture of an optical parametric amplifier (OPA) setup with the green pump beam visible aligned through a BBO crystal.37


The most-commonly used OPCPA architecture for few-cycle pulses in the visible is based on BBO as nonlinear material. This approach has been used to generate the current record performances in terms of peak power and average power. Here, the pump wavelength ranges typically from 343 to 532 nm, depending on the pump lasers. The typical amplification bandwidth ranges from <725 to >1050nm when pumped at 532 nm wavelength and 3 to 5 mm crystal lengths are employed.37 This bandwidth supports a transform-limited duration of <8fs or less than three optical cycles.38 Additionally, octave-spanning bandwidth to support quasi-single-cycle pulses can be obtained by pumping consecutive OPA stages with different wavelengths. This is most easily done with different harmonics of the fundamental pump laser, i.e., 532 and 355 nm for Nd:YAG-based pumps or 515 and 343 nm for Yb-based pumps. This concept was introduced in 2010 with mJ-level pulses39 and experimentally verified in a different setup in 2012 with microjoule-level pulse energies and compressed to 4.6-fs duration.40

The key parameters determining the parametric gain are the used pump intensity and the length of the crystal. Figure 2(a) shows example calculations for the parametric gain following the assumptions in Ref. 21 for BBO as nonlinear material. Pump intensities from 10 to 100GW/cm2 and crystal lengths from 1 to 5 mm are presented. It can be seen that a large parametric gain in excess of 106 can be obtained in these configurations. Experimentally, high parametric gains of 103 (Ref. 17), 104 (Ref. 41), or even 106 (Ref. 42) are typically employed in the first OPA stage of OPCPA systems, while a parametric gain of up to 108 has been experimentally demonstrated from a femtosecond OPA stage.43 Figure 2(b) shows the scaled damage threshold in BBO based on the empirical squared root scaling law of the damage threshold with pulse duration44 and values found in the literature.45,46 It can be seen that sub-100-ps pulses are necessary to avoid damage and enable pump intensities of 10GW/cm2 and above.

Fig. 2

(a) Calculated parametric gain in dependence of the interaction length and the pump intensity. (b) Scaled44 damage threshold45,46 of BBO in the femtosecond to nanosecond range.


On the other hand, it is well known that employing a shorter crystal has the benefit to relax requirements on the wave-vector mismatch for the OPA process. BBO crystals of several lengths have been utilized in the literature: for example, a single 1-mm-long BBO crystal for the amplification of sub-4-fs pulses36 and two 2-mm-long crystals for the amplification of 5.0-fs pulses to 87-μJ pulse energy.41 A combination of a 3-mm- and a 5-mm-long crystal has been used to amplify 5.7-fs pulses to 3-μJ pulse energy47 and two 5-mm-long crystals to amplify 7.9-fs pulses to 130-mJ pulse energy.17 In general, shorter crystals enable a wider phase-matching bandwidth and allow OPA stages to support almost-octave spanning bandwidths. In order to obtain the same gain from shorter crystals, higher pump intensities must be employed. A trend from reported OPCPA systems can be found in the utilization of short picosecond pump pulses, enabled by the recent developments in Yb-based CPA laser technology providing high-energy, high-average-power pumps with 0.5- to 1-ps duration.

The energy transfer efficiency in OPCPA from pump to signal pulse is typically on the order of 10 to 15% and dependent on the amplified bandwidth. Generating the record table-top, few-cycle OPCPA pulse energy of 130 mJ required a pump pulse energy of 1.0 J at 532 nm wavelength,17 and the record average power of 22 W required a pump laser with 120 W average power at 515 nm wavelength.13 For OPCPA at 2.1 μm center wavelength, the current record efficiency is 6.7% with an amplified pulse energy of 0.74 mJ pumped by 11 mJ pulse energy at 1053 nm wavelength.48 It is interesting to note that OPCPA compared to Ti:sapphire-based CPA is, in general, less efficient in terms of pump to signal conversion since Ti:sapphire systems operate with conversion efficiencies of 30 to 40%.49 In addition, it is worth noting that the required lasers to pump Ti:sapphire are typically commercially available, Nd-based, master oscillator power amplifiers (MOPA) providing high energetic nanosecond pulses (5 to 10 ns). In contrast, OPCPA requires extremely stable picosecond pump lasers with high peak power. The performance of such pump lasers is the primary limitation upon scaling of pulse energy and/or average power in OPCPA systems.


Traditional OPCPA Architecture

The amplification via OPCPA of few-cycle pulses typically follows the laser architecture21,23 as shown in Fig. 3 and described in the following. The front-end of the OPCPA architecture is typically a mode-locked, octave-spanning Ti:sapphire oscillator covering the required amplification bandwidth.50 However, a few OPCPA systems have been reported that utilize nonlinear spectral broadening of pulses from either a Ti:sapphire oscillator13,40 or a Ti:sapphire-based CPA system17 to seed the OPA. For center wavelengths different from the visible Ti:sapphire bandwidth, nonlinear frequency conversion based upon the octave-spanning Ti:sapphire bandwidth, typically via difference frequency generation (DFG)51,52 or OPA,16 has been employed to provide the seed pulses at various center wavelengths such as in the mid-IR. In addition, OPCPA systems seeded by stable white light filamentation in bulk material, such as a YAG plate generated by a portion of the typical sub-1-ps pump laser, have been reported.5354.55

Fig. 3

Traditional optical parametric chirped pulse amplification (OPCPA) architecture in the visible based upon a sub-5-fs oscillator, a pulse stretcher, the broadband amplification in the OPA, and a compressor to retrieve almost the original pulse duration. The pump beam is typically derived from the front-end oscillator to ensure optical synchronization and utilizes in the pump beam generation multiple amplification stages resulting in a high-energetic picosecond pump pulse.


Pulse stretching for sub-10-fs pulses in the visible can be achieved with a grism stretcher, based on a combination of grating and prism pairs, an acousto-optical programmable dispersive filter (AOPDF) for phase fine-adjustments and compression in bulk glass compressor. This method has been shown to allow complete dispersion compensation over >300nm bandwidth in the visible supporting sub-10-fs pulses56,57 and has been numerically extended for sub-5-fs pulses.58 For wavelengths in the IR, dispersive glasses can be utilized to up or down chirp the pulse and ultrashort pulse shapers such as AOPDF are commercially available.14,51 Dispersion management becomes increasingly challenging for wavelengths >4μm and mainly grating/grism pairs are used without adaptive shaping.59

In the traditional OPCPA architecture shown in Fig. 3, the pump laser is typically optically or electronically synchronized to the frond-end oscillator. The timing jitter requirement at the OPA stage ranges from sub-picosecond to 10 ps depending on the employed pulse durations, pulse shapes, and output stability requirements. The electronic synchronization has been presented for 60 ps pump pulse durations.60 The optical synchronization is commonly preferred since its performance is typically better than the minimum requirement.61 A jitter of several 100 fs from a pump scheme with sub-1-ps pulse duration has been reported as significant and was actively stabilized, since it otherwise induces fluctuations on the parametric gain, bandwidth, and center wavelength.62 Recently, an investigation has shown that the obtainable carrier-envelope phase (CEP) stability also depends on the pump-to-signal timing jitter and a CEP-stabilization with 86 mrad has been realized associated with a residual pump-to-signal timing jitter of 18±4fs with 500fs pump pulse duration.63


Visible to Mid-IR Few-Cycle Pulses

A major advantage of OPCPA compared to its main competitor, the Ti:sapphire-based CPA, is the possibility to operate at center wavelengths spanning the near-IR to the mid-IR. This is achieved by the choice of a nonlinear crystal, pump wavelength, as well as phase-matching geometry. Several OPCPA systems have been presented operating with few-cycle durations covering almost continuously the spectrum from the visible (0.6 μm) to the mid-IR (8 μm), which are summarized in Fig. 4. The transparency ranges of the employed nonlinear crystals are given, which were found via the freely available software package SNLO (AS-Photonics, LLC, Albuquerque, New Mexico).64

Fig. 4

The colored bars represent the few-cycle OPCPA bandwidth of reported systems for few different crystals, pump wavelengths, and phase matching condition. The gray bars represent the typical transparency range of the employed crystals. Note that the tuning range of the mentioned OPA stages can be larger than the indicated OPCPA bandwidths and extremely wide OPA tuning ranges covering the visible55 to near-IR65 and mid-IR66 have been reported.


A few crystal and wavelength combinations are detailed in the following. An OPCPA system has been presented in 2011, using MgO:PPLN (periodically poled lithium niobate) pumped at 1049 nm as well as a BBO crystal pumped at 1030 nm, providing parametric amplification from 1.8 to 2.5 μm centered at 2.1 μm.15,51 After compression, this produced few-cycle pulses with 0.85 mJ pulse energy at 1 kHz with 32 fs duration (4.5 optical cycles). A comparable system has been presented pumped at 1053 nm with 49 ps using PPLN and BBO crystals.48 This system operates with 15.7 fs duration (2 optical cycles) at 2.1 μm center wavelength and 0.74 mJ energy. Further in the IR, a system has been presented operating at 3.2 μm with 67 fs duration (6.3 optical cycles) and generating 3.8 μJ pulse energy at 100 kHz.15 A system operating at 3.9 μm was presented in 2011, which used KTA (Potassium Titanyl Arsenate, KTiOAsO4) crystals and produced pulses with 83 fs duration (7 optical cycles) and 8 mJ energy corresponding to 90 GW peak power.16 The longest-wavelength OPCPA presented to date provided amplification from 4.1 to 7.9 μm centered at 6 μm.59


Current Performance Level of Table-Top, Few-Cycle OPCPA

The performance of the reported OPCPA systems are listed in Table 1 and graphically represented in Fig. 5 with the year of publication noted (see Table 2 for list of acronyms). All of these systems operate with few-cycle pulse duration with center wavelengths ranging from 0.8 to 3.9 μm. A few outstanding record table-top OPCPA systems are listed in the following. The highest OPCPA peak power presented to date is 16 TW corresponding to 130 mJ and 7.9 fs duration with a contrast of 1012 for ±30ps.17 The record pulse energy for repetition rates around 1 kHz is 2.7 mJ with 5.5 fs pulse duration corresponding to a peak power of 490 GW.67 The highest average power was reported in Ref. 13 with 22 W at 1 MHz repetition rate and a nominal pulse duration of 5.0 fs corresponding to 1.7 optical cycles. Similar to other OPCPA publications with durations of 5.5 fs (Ref. 67) and 5.7 fs (Ref. 47), the reported central pulse of 5 to 6 fs duration is surrounded by side pulses, which potentially degrade pulse contrast and affect usability for high pulse intensity experiments.68

Fig. 5

Graphical overview of the performance of reported OPCPA systems. A color code is employed to emphasize the impact of the pump laser technology on the overall OPCPA performance. See Table 1 for the list of references and Table 2 for the list of acronyms.


Table 1

List of selected optical parametric chirped pulse amplification (OPCPA) systems reported in the literature, which are graphically illustrated in Fig. 5. See Table 2 for the list of acronyms.

RefPulse energyAverage powerPulse durationPeak powerCenter wavelengthPump technologyPump duration
3890 mJ0.9 W10 fs9.0 TW0.8 μmFlashlamp60 ps
6016 mJ0.47 W7.6 fs2.1 TW0.8 μmFlashlamp60 ps
65200 μJ0.2 W15 fs13 GW1.5 μmTi:sapphire50 fs
691.5 mJ1.5 W6.4 fs230 GW0.8 μmTi:sapphire100 ps
672.7 mJ2.7 W5.5 fs490 GW0.8 μmTi:sapphire75 ps
521.2 μJ0.12 W96 fs13 MW3.2 μmDPSS15 ps
42220 μJ0.22 W23 fs9.6 GW2.2 μmDPSS12 ps
48740 μJ0.74 W15.7 fs47 GW2.1 μmDPSS49 ps
170.13 J1.3 W7.9 fs16 TW0.805 μmFlashlamp78 ps
153.8 μJ0.38 W67 fs56 MW3.2 μmDPSS8 ps
530.4 μJ0.42 W9.7 fs43 MW0.8 μmFiber0.42 ps
7074 μJ7.1 W8.0 fs9.3 GW0.8 μmFiber0.78 ps
711.3 μJ0.19 W8.8 fs150 MW0.8 μmThin-disk1.6 ps
473 μJ0.43 W5.7 fs530 MW0.85 μmThin-disk1.6 ps
51850 μJ0.85 W32 fs27 GW2.1 μmCryo SS12 ps
4187 μJ2.61 W5.4 fs16 GW0.8 μmFiber0.70 ps
168 mJ0.16 W83 fs96 GW3.9 μmFlashlamp70 ps
1322 μJ22 W5.0 fs4.4 GW0.88 μmFiber0.50 ps
141.2 mJ3.6 W10.5 fs114 GW2.1 μmThin-disk1.6 ps

Table 2

List of acronyms and definitions.

FlashlampBased upon flashlamp-pumped amplifiers
Ti:sapphireBased upon Ti:sapphire-based amplifiers
DPSSBased upon diode-pumped solid-state amplifiers
FiberBased upon Yb-doped fiber-based amplifiers
Thin-diskBased upon Yb:YAG thin-disk amplifiers
Cryo SSBased upon cryogenically cooled Yb-based solid-state amplifiers
MOPAA system in master oscillator power amplifier configuration
CPAA system in chirped-pulse amplification configuration

Even shorter pulse durations have been reported recently, employing different pump wavelengths in multiple OPA stages. This method enabled the generation of a waveform with a 4.6 fs duration, where two consecutive OPA stages pumped by the second harmonic generation (SHG) and third harmonic generation of the pump beam, respectively, resulted in an amplified bandwidth covering from 430 to 1300 nm (40dB).40 In a similar scheme, two separate OPCPA systems have been employed (covering a bandwidth from 0.75 to 1.1 µm and 1.9 to 2.5 µm) to synthesize a waveform with a central region of 0.8 cycles (FWHM) corresponding to 2.1 fs.72 In contrast to these OPCPA systems with quasi-single-cycle pulses, visible sub-10-fs (Ref. 17) and near-IR sub-20-fs pulses42,48 can provide a more uniform spectrum, with potentially increased temporal contrast in the femto- to picosecond range. The shortest duration reported from OPA itself is 4.0 fs at a 600 nm center wavelength corresponding to 2.0 optical cycles.36 The lowest number of cycles reported is 1.5 at a center wavelength of 2.1 μm.14 Most of the record OPCPA performances were achieved when operated in the visible spectrum based upon BBO as a nonlinear medium.

Figure 5 employs a color code that relates the OPCPA performance to the utilized pump laser technology. It can be seen that high pulse energies, exceeding the 10 mJ-level, have only been achieved when pump lasers were employed based on flashlamp-pumped solid-state amplifiers. On the other hand, the highest average power regime demonstrations have utilized fiber and thin-disk pump lasers. For the range in between, several pump technologies have been employed providing comparable performance.

The reported OPCPA systems cover a wide parameter range due to the advantages of OPA and the absences of any stored energy in the nonlinear material (besides the parasitic effects discussed later in this paragraph). The latter is in contrast to traditional laser amplification based upon stimulated emission, in which a high amount of energy can be stored in the amplification medium resulting in thermally induced beam distortions, such as thermal lensing. For OPCPA, it seems that the performance is currently still scalable in terms of pulse energy and average power and that OPCPA is primarily limited by the performance of the employed pump lasers. It has been found recently that parasitic effects in the nonlinear crystal can lead to heat accumulation in the OPA stage of a high-average-power system. In this context, the most dominate parasitic effect in BBO-based visible NOPA, as shown experimentally in Ref. 73, results from absorption of the idler beam. This is due to the limited transparency range, which covers in a 1-cm-long BBO crystal the range from 0.2 to 2.6 μm for the 0.5 transmittance level, while the linear absorption value at 2.55 μm is significant at 0.5cm1.74 Thus, for visible NOPA covering the range from 625 to 950 nm, pumped at 515 nm and with generated idler beam ranging from 1.1 to 2.9 μm, the nonvanishing absorption in BBO can become a limiting factor for further power scaling beyond the current level. In addition, the non-negligible linear absorption across the transparency range (for example, in BBO of 0.01cm1 at 0.532 nm or 0.001cm1 at 1.0 μm)74 or multiphoton absorption results in additional heat accumulation. This heat-affected zone in the OPA stage can impact the phase-matching condition and induce thermal lensing or potentially fracture/damage the OPA material. These novel thermally induced effects in OPA are under investigation in many research laboratories around the world. We expect several approaches to mitigate thermal effects in OPAs emerging from this research.


Experimentally Demonstrated Pump Laser Schemes

Over the last seven years, several radically different pump laser schemes have been implemented as OPCPA pump lasers. Here, we review the progress of these laser systems and the influence on the OPCPA output performance. The performances of the pump lasers of the OPCPA systems from Fig. 5 are listed in Table 3 and graphically shown in Fig. 6 (see Table 2 for list of acronyms). The latter shows the pulse energy and average power of the employed pump lasers relative to the year of publication.

Fig. 6

Performance of OPCPA pump lasers in terms of pulse energy and average power against the year of publication. The pump laser systems are differentiated by color code corresponding to their laser technology. See Table 3 for the list of references and Table 2 for the list of acronyms.


Table 3

List of the performances of the pump lasers employed in reported OPCPA systems (Fig. 5), which are graphically illustrated in Figs. 6 and 7. See Table 2 for the list of acronyms.

Ref.Laser technologySchemePulse energyAverage powerPulse durationPeak power
38FlashlampMOPA1.15 J11.5 W110 ps10 GW
60FlashlampMOPA250 mJ7.5 W85 ps2.9 GW
65Ti:sapphireCPA1.5 mJ1.5 W50 fs30 GW
69Ti:sapphireMOPA21 mJ21 W141 ps150 MW
67Ti:sapphireMOPA29 mJ29 W106 ps273 MW
52DPSSMOPA65 μJ6.5 W15 ps4.3 MW
42DPSSMOPA4.5 mJ4.5 W12 ps380 MW
48DPSSMOPA11 mJ11 W49 ps225 MW
17FlashlampMOPA1.5 J15 W110 ps14 GW
15DPSSMOPA400 μJ40 W12 ps33 MW
53FiberCPA9 μJ9 W420 fs21 MW
70FiberCPA500 μJ49 W1.1 ps460 MW
71Thin-diskCPA40 μJ5.7 W1.56 ps25 MW
47Thin-diskCPA27 μJ3.85 W2.3 ps12 MW
51Cryo SSCPA16.5 mJ16.5 W12 ps1.4 GW
41FiberCPA890 μJ26.8 W990 fs900 MW
16FlashlampMOPA250 mJ5 W70 ps3.6 GW
13FiberCPA120 μJ120 W500 fs240 MW
14Thin-diskCPA20 mJ60 W1.6 ps12.5 GW

Several trends can be extracted from Fig. 6: It can be seen that the highest pulse energy has been achieved utilizing flashlamp-pumped solid-state amplifiers. Based on the performance shown in Fig. 6, flashlamp-pumped amplifiers are the only OPCPA-proven technology in this context that result in pump pulse energies >100mJ, with a record energy of 1.5 J with 15 W average power. The pulse provided by the system had 110 ps duration corresponding to 14 GW peak power at 1064 nm center wavelength.17 This pump laser generated the current record performance in terms of pulse energy and peak power for table-top OPCPA systems with an output of 130 mJ and 16 TW, respectively. Other systems have been presented for OPCPA pumping, such as a 250-mJ pulse energy system with 70 ps duration at 20 Hz repetition rate16 and a system providing 160-mJ, 60-ps pulses at 30 Hz.60 It can be seen that high pulse energy is achieved with this technology, but the corresponding average power is limited to the 20 W-level.

On the other side, the highest average power was demonstrated with a fiber-based pump laser system. This system operated at a repetition rate of 1 MHz providing 200 W average power and 200 μJ pulse energy at 1030 nm center wavelength with 0.47 ps duration before SHG to 515 nm to pump an OPCPA system.13 This pump laser enabled the record OPCPA average power performance of 22 W with a peak power of 4.4 GW.13

Several systems have been presented providing both high pulse energy as well as high average power. The earliest systems were based on narrow-band, picosecond pump systems providing 10 mJ-level pulse energies at kilohertz repetition rate. In 2007, such a pump system based on Ti:sapphire amplifiers provided 4 and 10 mJ at 400 nm with 70ps duration.69 A Nd:YLF regenerative and multistage amplifiers were used to generate 11 mJ at 1 kHz repetition rate with 49 ps duration.48 A similar system of Nd:YLF regenerative and multipass amplifier was used to generate 7 mJ pulse energy with 110 ps duration, which was compressed to 12 ps and 4.5 mJ.42 A commercial mode-locked Nd:YVO4 system (Lumera Laser GmbH, Germany) producing 10 W at 100 kHz with 0.1 mJ pulse energy and 8.7 ps duration was the OPCPA pump laser in Ref. 52.

More recently, Yb-based CPA systems have been introduced as OPCPA pumps allowing significant increases in average power due to their superior thermal handling compared to Nd-based systems and reduction in pulse duration via CPA. A cryogenically cooled solid-state system has been used as OPCPA pump based on a Yb:YAG regenerative amplifier operating at 1 kHz, 13 mJ, 15 ps, 13 W.51 A Yb:YAG thin-disk system has been used as a pump with 20 mJ at 1030 nm and 3 kHz, 1.6 ps duration.14 The performance benefits of Yb-based CPA systems are highlighted in Sec. 3.3.


Recent Developments on Picosecond, High-Energy, and High-Average-Power Lasers

This section reviews the recent progress in relevant laser technologies that will impact the performance of the OPCPA systems in the near future. The pump laser systems mentioned in Sec. 2.5 are listed in Table 3 and graphically shown in Fig. 7(a) in terms of pulse energy and average power. Similarly, the performances of several recently reported laser systems are listed in Table 4 and graphically shown in Fig. 7(b) (see Table 2 for list of acronyms). These two figures are placed next to one another in order to directly compare the performance of pump lasers that have been employed for OPCPA with that of recently reported picosecond laser systems. In addition, trends are identified in this chapter for the recently reported systems and the direct impact on the performance of OPCPA systems in the near future is discussed.

Fig. 7

(a) Performances of the pump lasers of reported OPCPA systems in terms of pulse energy and average power. (b) Performance of recently demonstrated high-energy, high-average-power picosecond laser system. The laser systems are differentiated by color code corresponding to their laser technology. See Tables 3 and 4 for the list of references and Table 2 for the list of acronyms.


Table 4

List of the performances of high-energy, high-average-power picosecond laser systems reported over the last years, which satisfy the performance requirements to pump OPCPA. These systems are graphically illustrated in Fig. 7. See Table 2 for the list of acronyms.

Ref.Laser technologySchemePulse energyAverage powerPulse durationPeak power
75DPSSMOPA130 μJ5.3 W19 ps7 MW
76DPSSMOPA123 μJ12 W6.8 ps18 MW
77Cryo SSMOPA3.7 μJ287 W5.5 ps670 kW
78Cryo SSCPA300 μJ6 W195 fs1.5 GW
79Thin-diskCPA25 mJ75 W1.6 ps15 GW
80Thin-diskCPA300 mJ3 W2 ps150 GW
81Cryo SSMOPA15 μJ760 W12 ps1.2 MW
82Cryo SSCPA6.5 mJ13 W15 ps433 MW
83DPSSMOPA3 mJ30 W25 ps118 MW
84DPSS slabCPA5.5 μJ1.1 kW610 fs9 MW
85FiberCPA3.1 μJ3.1 W140 fs22 MW
86FiberCPA11 μJ830 W0.64 fs12 MW
87Cryo SSCPA100 mJ10 W5 ps20 GW
88Cryo SSCPA12 mJ60 W1.6 ps7.5 GW
89DPSSCPA27 mJ2.7 W560 fs48 GW
90DPSS ceramicCPA130 mJ1.3 W450 fs290 GW
91DPSSMOPA1.8 mJ8.8 W28 ps62 MW
92DPSSCPA200 mJ2 W900 fs222 GW
93DPSSMOPA500 μJ5 W85 ps5.8 MW
94DPSSMOPA40 mJ40 W48 ps833 MW
54DPSS slabCPA20 mJ250 W830 fs24 GW
95DPSS slabMOPA600 μJ30 W12 ps50 MW
96FiberCPA3 mJ30 W470 fs6.4 GW
97FiberCPA2.2 mJ11 W500 fs4.4 GW
98Cryo SSCPA11 mJ106 W865 fs12.3 GW
99Cryo SSCPA1 J100 W5 ps200 GW
100DPSSCPA40 μJ8 W180 fs220 MW
101FiberCPA3 μJ3 W50 fs60 MW
102FlashlampMOPA300 mJ3 W141 ps2.1 GW


Flashlamp-Pumped and Diode-Pumped Solid-State MOPA Systems

The highest pulse energies from OPCPA systems have been reported when employing flashlamp-pumped solid-state amplifiers. The technology utilizes large-aperture Nd:YAG rods with large amounts of stored energy to reach joule-level pulse energies with repetition rates of 30 Hz and lower. Based on the comparison here, no other laser technology has been used to obtain higher pulse energies. Since this technology offers compact optical setup, it is the most common path for the generation of ultrahigh-energy pulses and moderate average powers. Thus, the current record OPCPA peak power of 16 TW was enabled by flashlamp-pumped amplifiers in the pump beam generation. Higher average powers are generally prohibited by the low efficiency of flashlamp pumping and the associated demands on the high-voltage power supplies/switching electronics. As a consequence, this mature technology has been generally limited to 10 W-level average powers but with ultrahigh pulse energies at the joule-level.

A compromise between pulse energy and average power can be realized with diode-pumped solid-state amplifiers, such as Nd:YAG or Nd:YVO4. In this case, the average powers are sufficiently high that thermally induced lensing and depolarization must be compensated. A system has been demonstrated operating at 1 kHz with Nd:YAG amplifiers producing an output energy of 40 mJ, 48 ps duration and a corresponding average power of 40 W.94 At higher repetition rates, a system has been presented operating with 33.7 W and 20 kHz with 220ps pulse duration corresponding to 7 MW peak power.103 Another system has been demonstrated based on Nd:YVO4 slab amplifier with 0.6 mJ pulse energy and 12 ps duration corresponding to an average/peak power between 46W/38MW and 30W/50MW.95 All of these systems offer high performance with compact footprint due to the MOPA architecture.


Yb:YAG Thin-Disk and Yb:Fiber CPA Systems

Compared to Nd-based amplifiers, the quantum defect is 10% in Yb:YAG whereas it is 25% in Nd:YAG, resulting in higher optical-to-optical efficiency and lower thermal load at comparable operational power. Several novel laser/amplifier configurations have been developed to reduce the thermal distortions. The thin-disk approach is one example in which a Yb:YAG crystal with few hundred micrometers thickness and few millimeters diameter is utilized. This heat removal scheme minimizes thermally induced beam distortions without the need for complex compensation. Extraction of up to 25 mJ at 3 kHz repetition rate with 1.6 ps duration has been presented.92 However, due to the small thickness of the disk, the scheme has to overcome low pump absorption and low small signal gain (on occasion <1.1) with a high number of passes for pump and signal, such as 20 passes of the pump and 300 bounces in the case of regenerative amplifier reported in Ref. 92. A 15-pass amplifier was presented based on a thin-disk to amplify a 10-Hz burst of 80 pulses at 100 kHz repetition rate with 25 mJ per pulse.104

Recent progress in large-pitch photonic crystal fibers has allowed the increase of pulse energy in fiber amplifier systems to impressive levels. CPA systems based on such fibers have been already used as OPCPA pump with up to 200 W average power resulting in the current record OPCPA average power.13 A similar performance has been shown from a system providing up to 830 W average and 10.6 μJ pulse energy with sub-picosecond pulse duration.86 For higher pulse energies, a similar fiber system has been employed to generate 2.2 mJ pulse energy with sub-ps duration97 and 3 mJ when beam combining is utilized.96 Thus, fiber amplifier based systems offer high average power performance in highly stable and compact architectures.


Yb-Based Cryogenically Cooled Solid-State and Slab Systems

Several relevant properties of Yb:YAG improve when operating at cryogenic temperatures. The level scheme becomes an almost four-level minimizing reabsorption, the stimulated cross-section improves by 5, while the thermal conductivity increases 2.5 to 4 times depending on the dopant level.81 However, the emission linewidth and thus, the amplification bandwidths of these systems reduce to typically <1nm, corresponding to a transform-limited pulse duration of 5ps. A few cryogenically cooled systems have been presented, such as a system generating 287 W average power with 5.5 ps duration pulses corresponding to 3.7 μJ pulse energy.77 Another system has been reported based on cryogenically cooled, thick-disk, Yb:YAG producing up to 100 mJ at 100 Hz with a compressed duration of 5 ps.87 The performance of the system has been further scaled to generate an output of 1 J pulse energy with 5 ps duration corresponding to 100 W average power.99 A system with a double- and single-pass amplifier was presented based on multiple thick Yb:YAG disks generating up to 15.2 μJ pulse energy with 760 W average power and 12 ps duration.81

Another scheme to reduce thermally induced aberrations is a slab amplifier. The beam multipasses through the slab offering lower thermal aberration compared to rod-type designs, high small signal gain as well as a compact design. One such system based on a Yb:YAG slab generated 0.64 ps pulses with up to 1.1 kW average power at 20 MHz corresponding to a peak power of 80 MW.84 At 12.5 kHz repetition rate, a similar amplifier scheme has been used to generate 20 mJ pulse energy with 0.83 ps after postcompression corresponding to an average power of 250 W.54


Trends and Impact for Few-Cycle OPCPA

The mentioned laser technologies are employed with a wide range of output parameters. Figure 7 shows the performance in terms of pulse energy and average power for some potential pump systems in contrast to those already employed for OPCPA pumping. It can be seen that novel laser technologies offer an order of magnitude improvement in average power relative to the performance employed to pump OPCPA systems to date. Although many of these new systems have not been characterized for the strict OPCPA requirements in terms of low noise, fluctuations, and jitter, the implementation of higher-average-power pump lasers is within reach.

A few notable pump lasers have been presented. For example, if the cryogenically cooled, Yb:YAG, thick-disk amplifier producing 1 J pulses with 5 ps duration99 were employed as an OPCPA pump, few-cycle pulses could be generated with 100 mJ at 100 Hz corresponding to 10 W average power. Similarly, if the Yb:YAG slab amplifier producing 0.83 ps pulses with 20 mJ energy54 were employed, an OPCPA output of 2 mJ at 12.5 kHz could be obtained. As a consequence, we expect to see a sharp increase of available pump power in the next years, enabling OPCPA with energies from 1 to 100 mJ and repetition rate from 100 Hz to 10 kHz outperforming Ti:sapphire-based CPA systems.


Summary and Outlook

In this article, we have reviewed the concepts behind table-top, few-cycle OPCPA as well as the current performance level obtained in research laboratories around the world. The current performance level of table-top OPCPA is primarily limited by the performance of the employed pump laser. Today, the OPCPA method has reached a performance level comparable to Ti:sapphire-based CPA technology with multi-10 TW peak power, mJ-level pulse energy at several kilohertz repetition rate, or ultra-high repetition rates with >20W average power. Although thermal effects have been observed in the OPA, this is not yet a significant limit on average power scaling.

We also have presented an overview of recently reported high-energy, high-average-power, picosecond laser systems. Several promising laser systems have been presented, producing >100W average power with high pulse energy and picosecond pulse duration. Thus, it seems feasible to obtain in the near future few-cycle pulses with multi-mJ-level energy in the visible, near-IR, or mid-IR via OPCPA at the 10 W average power level.


1. D. StricklandG. Mourou, “Compression of amplified chirped optical pulses,” Opt. Commun. 55(6), 447–449 (1985).OPCOB80030-4018 http://dx.doi.org/10.1016/0030-4018(85)90151-8 Google Scholar

2. P. Maineet al., “Generation of ultrahigh peak power pulses by chirped pulse amplification,” IEEE J. Quantum Electron. 24(2), 398–403 (1988).IEJQA70018-9197 http://dx.doi.org/10.1109/3.137 Google Scholar

3. T. Tanabeet al., “Compensation for a transfer function of a regenerative amplifier to generate accurately shaped ultrashort pulses in both the amplitude and phase,” IEEE J. Sel. Topics Quantum Electron. 10(1), 221–228 (2004).IJSQEN1077-260X http://dx.doi.org/10.1109/JSTQE.2004.824069 Google Scholar

4. M. Nisoliet al., “A novel-high energy pulse compression system: generation of multigigawatt sub-5-fs pulses,” Appl. Phys. B 65(2), 189–196 (1997).APBOEM0946-2171 http://dx.doi.org/10.1007/s003400050263 Google Scholar

5. T. BrabecF. Krausz, “Intense few-cycle laser fields: frontiers of nonlinear optics,” Rev. Mod. Phys. 72(2), 545–591 (2000).RMPHAT0034-6861 http://dx.doi.org/10.1103/RevModPhys.72.545 Google Scholar

6. S. Bohmanet al., “Generation of 5.0 fs, 5.0 mJ pulses at 1 kHz using hollow-fiber pulse compression,” Opt. Lett. 35(11), 1887–1889 (2010).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.35.001887 Google Scholar

7. C. P. Hauriet al., “Generation of intense, carrier-envelope phase-locked few-cycle laser pulses through filamentation,” Appl. Phys. B 79(6), 673–677 (2004).APBOEM0946-2171 http://dx.doi.org/10.1007/s00340-004-1650-z Google Scholar

8. G. StibenzN. ZhavoronkovG. Steinmeyer, “Self-compression of millijoule pulses to 7.8 fs duration in a white-light filament,” Opt. Lett. 31(2), 274–276 (2006).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.31.000274 Google Scholar

9. A. MysyrowiczA. CouaironU. Keller, “Self-compression of optical laser pulses by filamentation,” New J. Phys. 10(2), 025023 (2008).NJOPFM1367-2630 http://dx.doi.org/10.1088/1367-2630/10/2/025023 Google Scholar

10. I. MatsushimaH. YashiroT. Tomie, “10 kHz 54 W Ti:sapphire regenerative amplifier as a pumping laser of a laser-plasma x-ray source,” Proc. SPIE 7022, 70220M (2008).PSISDG0277-786X http://dx.doi.org/10.1117/12.803939 Google Scholar

11. I. MatsushimaH. YashiroT. Tomie, “10 kHz 40 W Ti:sapphire regenerative ring amplifier,” Opt. Lett. 31(13), 2066–2068 (2006).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.31.002066 Google Scholar

12. A. DubietisG. JonušauskasA. Piskarskas, “Powerful femtosecond pulse generation by chirped and stretched pulse parametric amplification in BBO crystal,” Opt. Commun. 88(4–6), 437–440 (1992).OPCOB80030-4018 http://dx.doi.org/10.1016/0030-4018(92)90070-8 Google Scholar

13. J. Rothhardtet al., “Octave-spanning OPCPA system delivering CEP-stable few-cycle pulses and 22 W of average power at 1 MHz repetition rate,” Opt. Express 20(10), 10870–10878 (2012).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.20.010870 Google Scholar

14. Y. Denget al., “Carrier-envelope-phase-stable, 1.2 mJ, 1.5 cycle laser pulses at 2.1 μm,” Opt. Lett. 37(23), 4973–4975 (2012).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.37.004973 Google Scholar

15. O. Chaluset al., “Six-cycle mid-infrared source with 3.8 μJ at 100 kHz,” Opt. Lett. 35(19), 3204–3206 (2010).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.35.003204 Google Scholar

16. G. Andriukaitiset al., “90 GW peak power few-cycle mid-infrared pulses from an optical parametric amplifier,” Opt. Lett. 36(15), 2755–2757 (2011).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.36.002755 Google Scholar

17. D. Herrmannet al., “Generation of sub-three-cycle, 16 TW light pulses by using noncollinear optical parametric chirped-pulse amplification,” Opt. Lett. 34(16), 2459–2461 (2009).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.34.002459 Google Scholar

18. R. Butkuset al., “Progress in chirped pulse optical parametric amplifiers,” Appl. Phys. B 79(6), 693–700 (2004).APBOEM0946-2171 http://dx.doi.org/10.1007/s00340-004-1614-3 Google Scholar

19. A. DubietisR. ButkusA. P. Piskarskas, “Trends in chirped pulse optical parametric amplification,” IEEE J. Sel. Topics Quantum Electron. 12(2), 163–172 (2006).IJSQEN1077-260X http://dx.doi.org/10.1109/JSTQE.2006.871962 Google Scholar

20. S. WitteK. S. E. Eikema, “Ultrafast optical parametric chirped-pulse amplification,” IEEE J. Sel. Topics Quantum Electron. 18(1), 296–307 (2012).IJSQEN1077-260X http://dx.doi.org/10.1109/JSTQE.2011.2118370 Google Scholar

21. G. CerulloS. De Silvestri, “Ultrafast optical parametric amplifiers,” Rev. Sci. Instrum. 74(1), 1–18 (2003).RSINAK0034-6748 http://dx.doi.org/10.1063/1.1523642 Google Scholar

22. S. Witteet al., “Numerical simulations for performance optimization of a few-cycle terawatt NOPCPA system,” Appl. Phys. B 87(4), 677–684 (2007).APBOEM0946-2171 http://dx.doi.org/10.1007/s00340-007-2640-8 Google Scholar

23. I. N. Rosset al., “The prospects for ultrashort pulse duration and ultrahigh intensity using optical parametric chirped pulse amplifiers,” Opt. Commun. 144(1–3), 125–133 (1997).OPCOB80030-4018 http://dx.doi.org/10.1016/S0030-4018(97)00399-4 Google Scholar

24. O. V. Chekhlovet al., “35 J broadband femtosecond optical parametric chirped pulse amplification system,” Opt. Lett. 31(24), 3665–3667 (2006).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.31.003665 Google Scholar

25. I. N. Rosset al., “Analysis and optimization of optical parametric chirped pulse amplification,” J. Opt. Soc. Am. B 19(12), 2945–2956 (2002).JOBPDE0740-3224 http://dx.doi.org/10.1364/JOSAB.19.002945 Google Scholar

26. C. N. Dansonet al., “Vulcan petawatt: design, operation and interactions at 5×1020Wcm2,” Laser Part. Beams 23(1), 87–93 (2005).LPBEDA0263-0346 http://dx.doi.org/10.1017/S0263034605050159 Google Scholar

27. O. Nováket al., “Design of a petawatt optical parametric chirped pulse amplification upgrade of the kilojoule iodine laser PALS,” Laser Part. Beams 31(02), 211–218 (2013).LPBEDA0263-0346 http://dx.doi.org/10.1017/S0263034613000189 Google Scholar

28. G. M. Galeet al., “Sub-20-fs tunable pulses in the visible from an 82-MHz optical parametric oscillator,” Opt. Lett. 20(14), 1562–1564 (1995).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.20.001562 Google Scholar

29. G. M. GaleF. HacheM. Cavallari, “Broad-bandwidth parametric amplification in the visible: femtosecond experiments and simulations,” IEEE J. Sel. Topics Quantum Electron. 4(2), 224–229 (1998).IJSQEN1077-260X http://dx.doi.org/10.1109/2944.686727 Google Scholar

30. M. Nisoliet al., “Parametric generation of high-energy 14.5-fs light pulses at 1.5 μm,” Opt. Lett. 23(8), 630–632 (1998).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.23.000630 Google Scholar

31. G. Cerulloet al., “Sub-8-fs pulses from an ultrabroadband optical parametric amplifier in the visible,” Opt. Lett. 23(16), 1283–1285 (1998).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.23.001283 Google Scholar

32. T. WilhelmJ. PielE. Riedle, “Sub-20-fs pulses tunable across the visible from a blue-pumped single-pass noncollinear parametric converter,” Opt. Lett. 22(19), 1494–1496 (1997).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.22.001494 Google Scholar

33. E. Riedleet al., “Generation of 10 to 50 fs pulses tunable through all of the visible and the NIR,” Appl. Phys. B 71(3), 457–465 (2000).APBOEM0946-2171 http://dx.doi.org/10.1007/s003400000351 Google Scholar

34. A. ShirakawaI. SakaneT. Kobayashi, “Pulse-front-matched optical parametric amplification for sub-10-fs pulse generation tunable in the visible and near infrared,” Opt. Lett. 23(16), 1292–1294 (1998).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.23.001292 Google Scholar

35. T. KobayashiA. Shirakawa, “Tunable visible and near-infrared pulse generator in a 5 fs regime,” Appl. Phys. B 70(1), 239–246 (2000).APBOEM0946-2171 http://dx.doi.org/10.1007/s003400000325 Google Scholar

36. A. BaltuškaT. FujiT. Kobayashi, “Visible pulse compression to 4 fs by optical parametric amplification and programmable dispersion control,” Opt. Lett. 27(5), 306–308 (2002).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.27.000306 Google Scholar

37. M. HemmerA. VaupelM. Richardson, “Current status of the HERACLES, a millijoule level, multi kHz, few-cycle, and CEP stabilized OPCPA system,” in Conf. on Lasers and Electro-Optics and Quantum Electronics and Laser Science, pp. 1–2, Optical Society of America (2010). Google Scholar

38. F. TavellaA. MarcinkeviciusF. Krausz, “90 mJ parametric chirped pulse amplification of 10 fs pulses,” Opt. Express 14(26), 12822–12827 (2006).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.14.012822 Google Scholar

39. D. Herrmannet al., “Approaching the full octave: noncollinear optical parametric chirped pulse amplification with two-color pumping,” Opt. Express 18(18), 18752–18762 (2010).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.18.018752 Google Scholar

40. A. Harthet al., “Two-color pumped OPCPA system emitting spectra spanning 1.5 octaves from VIS to NIR,” Opt. Express 20(3), 3076–3081 (2012).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.20.003076 Google Scholar

41. S. Hädrichet al., “High-repetition-rate sub-5-fs pulses with 12 GW peak power from fiber-amplifier-pumped optical parametric chirped-pulse amplification,” Opt. Lett. 36(3), 313–315 (2011).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.36.000313 Google Scholar

42. J. Moseset al., “Highly stable ultrabroadband mid-IR optical parametric chirped-pulse amplifier optimized for superfluorescence suppression,” Opt. Lett. 34(11), 1639–1641 (2009).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.34.001639 Google Scholar

43. V. Krylovet al., “Efficient noncollinear parametric amplification of weak femtosecond pulses in the visible and near-infrared spectral range,” Opt. Lett. 23(2), 100–102 (1998).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.23.000100 Google Scholar

44. B. C. Stuartet al., “Nanosecond-to-femtosecond laser-induced breakdown in dielectrics,” Phys. Rev. B 53(4), 1749–1761 (1996).PRBMDO1098-0121 http://dx.doi.org/10.1103/PhysRevB.53.1749 Google Scholar

45. H. Nakataniet al., “Laser-induced damage in beta-barium metaborate,” Appl. Phys. Lett. 53(26), 2587 (1988).APPLAB0003-6951 http://dx.doi.org/10.1063/1.100535 Google Scholar

46. C. Chenet al., “New nonlinear-optical crystal: LiB3O5,” J. Opt. Soc. Am. B 6(4), 616–621 (1989).JOBPDE0740-3224 http://dx.doi.org/10.1364/JOSAB.6.000616 Google Scholar

47. M. Schultzeet al., “Multi-μJ, CEP-stabilized, two-cycle pulses from an OPCPA system with up to 500 kHz repetition rate,” Opt. Express 18(26), 27291–27297 (2010).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.18.027291 Google Scholar

48. X. Guet al., “Generation of carrier-envelope-phase-stable 2-cycle 740-μJ pulses at 2.1-μm carrier wavelength,” Opt. Express 17(1), 62–69 (2009).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.17.000062 Google Scholar

49. S. Backuset al., “High power ultrafast lasers,” Rev. Sci. Instrum. 69(3), 1207–1223 (1998).RSINAK0034-6748 http://dx.doi.org/10.1063/1.1148795 Google Scholar

50. R. Ellet al., “Generation of 5-fs pulses and octave-spanning spectra directly from a Ti:sapphire laser,” Opt. Lett. 26(6), 373–375 (2001).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.26.000373 Google Scholar

51. K.-H. Honget al., “High-energy, phase-stable, ultrabroadband kHz OPCPA at 2.1 μm pumped by a picosecond cryogenic Yb:YAG laser,” Opt. Express 19(16), 15538–15548 (2011).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.19.015538 Google Scholar

52. O. Chaluset al., “Mid-IR short-pulse OPCPA with micro-joule energy at 100 kHz,” Opt. Express 17(5), 3587–3594 (2009).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.17.003587 Google Scholar

53. M. Emonset al., “Sub-10-fs pulses from a MHz-NOPA with pulse energies of 0.4 μJ,” Opt. Express 18(2), 1191–1196 (2010).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.18.001191 Google Scholar

54. M. Schulzet al., “Yb:YAG Innoslab amplifier: efficient high repetition rate subpicosecond pumping system for optical parametric chirped pulse amplification,” Opt. Lett. 36(13), 2456–2458 (2011).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.36.002456 Google Scholar

55. C. Homannet al., “Octave wide tunable UV-pumped NOPA: pulses down to 20 fs at 0.5 MHz repetition rate,” Opt. Express 16(8), 5746–5756 (2008).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.16.005746 Google Scholar

56. D. M. Gaudiosiet al., “Multi-kilohertz repetition rate Ti:sapphire amplifier based on down-chirped pulse amplification,” Opt. Express 14(20), 9277–9283 (2006).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.14.009277 Google Scholar

57. F. Tavellaet al., “Dispersion management for a sub-10-fs, 10 TW optical parametric chirped-pulse amplifier,” Opt. Lett. 32(15), 2227–2229 (2007).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.32.002227 Google Scholar

58. T. H. Douet al., “Dispersion control with reflection grisms of an ultra-broadband spectrum approaching a full octave,” Opt. Express 18(26), 27900–27909 (2010).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.18.027900 Google Scholar

59. S. Alisauskaset al., “Micro-joule octave spanning pulses at 6 μm from a hybrid femtosecond OPA,” in Lasers, Sources, and Related Photonic Devices, Paper AM1A.6, Optical Society of America (2012). Google Scholar

60. S. Witteet al., “A source of 2 terawatt, 2.7 cycle laser pulses based on noncollinear optical parametric chirped pulse amplification,” Opt. Express 14(18), 8168–8177 (2006).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.14.008168 Google Scholar

61. C. Y. Teissetet al., “Soliton-based pump-seed synchronization for few-cycle OPCPA,” Opt. Express 13(17), 6550–6557 (2005).OPEXFF1094-4087 http://dx.doi.org/10.1364/OPEX.13.006550 Google Scholar

62. S. Klingebielet al., “Experimental and theoretical investigation of timing jitter inside a stretcher-compressor setup,” Opt. Express 20(4), 3443–3455 (2012).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.20.003443 Google Scholar

63. S. Hädrichet al., “Improving carrier-envelope phase stability in optical parametric chirped-pulse amplifiers by control of timing jitter,” Opt. Lett. 37(23), 4910–4912 (2012).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.36.000313 Google Scholar

64. AS-Photonics, “SNLO,”  http://www.as-photonics.com/ (1 July 2013). Google Scholar

65. C. Vozziet al., “High-energy, few-optical-cycle pulses at 1.5 μm with passive carrier-envelope phase stabilization,” Opt. Express 14(21), 1150–1152 (2006).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.14.010109 Google Scholar

66. G. Cirmiet al., “Carrier-envelope phase stable, few-optical-cycle pulses tunable from visible to near IR,” J. Opt. Soc. Am. B 25(7), B62 (2008).JOBPDE0740-3224 http://dx.doi.org/10.1364/JOSAB.25.000B62 Google Scholar

67. S. Adachiet al., “5-fs, multi-mJ, CEP-locked parametric chirped-pulse amplifier pumped by a 450-nm source at 1 kHz,” Opt. Express 16(19), 8168–8177 (2008).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.16.014341 Google Scholar

68. J. M. Mikhailovaet al., “Ultra-high-contrast few-cycle pulses for multipetawatt-class laser technology,” Opt. Lett. 36(16), 3145–3147 (2011).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.36.003145 Google Scholar

69. S. Adachiet al., “1.5 mJ, 6.4 fs parametric chirped-pulse amplification system at 1 kHz,” Opt. Lett. 32(17), 2487–2489 (2007).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.32.002487 Google Scholar

70. J. Rothhardtet al., “High average and peak power few-cycle laser pulses delivered by fiber pumped OPCPA system,” Opt. Express 18(12), 12719–12726 (2010).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.18.012719 Google Scholar

71. M. Schultzeet al., “Few-cycle OPCPA system at 143 kHz with more than 1 microJ of pulse energy,” Opt. Express 18(3), 2836–2841 (2010).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.18.002836 Google Scholar

72. S. Huanget al., “High-energy pulse synthesis with sub-cycle waveform control for strong-field physics,” Nat. Photonics 5(8), 475–479 (2011).1749-4885 http://dx.doi.org/10.1038/nphoton.2011.140 Google Scholar

73. J. Rothhardtet al., “Thermal effects in high average power optical parametric amplifiers,” Opt. Lett. 38(5), 763–765 (2013).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.38.000763 Google Scholar

74. D. N. Nikogosyan, Nonlinear Optical Crystals: A Complete Survey, Chapter 2, Springer Science+Business Media, Inc., New York (2005). Google Scholar

75. M. Sieboldet al., “A high-average-power diode-pumped Nd:YVO4 regenerative laser amplifier for picosecond-pulses,” Appl. Phys. B 78(3–4), 287–290 (2004).APBOEM0946-2171 http://dx.doi.org/10.1007/s00340-003-1372-7 Google Scholar

76. J. KleinbauerR. KnappeR. Wallenstein, “13-W picosecond Nd:YVO4 regenerative amplifier with 200-kHz repetition rate,” Appl. Phys. B 81(2–3), 163–166 (2005).APBOEM0946-2171 http://dx.doi.org/10.1007/s00340-005-1903-5 Google Scholar

77. K.-H. Honget al., “Generation of 287 W, 5.5 ps pulses at 78 MHz repetition rate from a cryogenically cooled Yb:YAG amplifier seeded by a fiber chirped-pulse amplification system,” Opt. Lett. 33(21), 2473–2475 (2008).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.33.002473 Google Scholar

78. A. Pugžlyset al., “Multi-mJ, 200-fs, cw-pumped, cryogenically cooled, Yb,Na:CaF2 amplifier,” Opt. Lett. 34(13), 2075–2077 (2009).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.34.002075 Google Scholar

79. T. Metzgeret al., “High-repetition-rate picosecond pump laser based on a Yb:YAG disk amplifier for optical parametric amplification,” Opt. Lett. 34(14), 2123–2125 (2009).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.34.002123 Google Scholar

80. J. Tümmleret al., “High-repetition-rate chirped-pulse-amplification thin-disk laser system with joule-level pulse energy,” Opt. Lett. 34(9), 1378–1380 (2009).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.34.001378 Google Scholar

81. D. C. Brownet al., “High sustained average power cw and ultrafast Yb:YAG near-diffraction-limited cryogenic solid-state laser,” Opt. Express 18(24), 24770–24792 (2010).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.18.024770 Google Scholar

82. K.-H. Honget al., “High-energy, kHz-repetition-rate, ps cryogenic Yb:YAG chirped-pulse amplifier,” Opt. Lett. 35(11), 1752–1754 (2010).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.35.001752 Google Scholar

83. J. Fuet al., “Picosecond laser system with 30-W average power via cavity dumping and amplifying,” Laser Phys. 21(6), 1042–1046 (2011).LAPHEJ1054-660X http://dx.doi.org/10.1134/S1054660X11110090 Google Scholar

84. P. Russbueldtet al., “Compact diode-pumped 1.1 kW Yb:YAG Innoslab femtosecond amplifier,” Opt. Lett. 35(24), 4169–4171 (2010).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.35.004169 Google Scholar

85. H. Kalayciogluet al., “Microjoule-energy, 1 MHz repetition rate pulses from all-fiber-integrated nonlinear chirped-pulse amplifier,” Opt. Lett. 35(7), 959–961 (2010).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.35.000959 Google Scholar

86. T. Eidamet al., “Femtosecond fiber CPA system emitting 830 W average output power,” Opt. Lett. 35(2), 94–96 (2010).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.35.000094 Google Scholar

87. A. H. Curtiset al., “Demonstration of a compact 100 Hz, 0.1 J, diode-pumped picosecond laser,” Opt. Lett. 36(11), 2164–2166 (2011).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.36.002164 Google Scholar

88. D. A. Randet al., “Picosecond pulses from a cryogenically cooled, composite amplifier using Yb:YAG and Yb:GSAG,” Opt. Lett. 36(3), 340–342 (2011).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.36.000340 Google Scholar

89. D. N. Papadopouloset al., “Broadband high-energy diode-pumped Yb:KYW multipass amplifier,” Opt. Lett. 36(19), 3816–3818 (2011).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.36.003816 Google Scholar

90. M. Suzukiet al., “Hundred mJ, sub-picoseconds, high temporal contrast OPCPA/Yb:YAG ceramic thin disk hybrid laser system,” Appl. Phys. B 105(2), 181–184 (2011).APBOEM0946-2171 http://dx.doi.org/10.1007/s00340-011-4752-4 Google Scholar

91. H. Linet al., “High-power picosecond regenerative amplifier based on CW diode side-pumped Nd:YAG with high beam quality,” Chinese Opt. Lett. 9(8), 081404 (2011).COLHBT1671-7694 Google Scholar

92. S. Klingebielet al., “High energy picosecond Yb:YAG CPA system at 10 Hz repetition rate for pumping optical parametric amplifiers,” Opt. Express 19(6), 5357–5363 (2011).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.19.005357 Google Scholar

93. M. Hemmeret al., “OPCPA pump laser based on a regenerative amplifier with volume Bragg grating spectral filtering,” Appl. Phys. B 106(3), 599–603 (2012).APBOEM0946-2171 http://dx.doi.org/10.1007/s00340-011-4843-2 Google Scholar

94. K. MichailovasV. SmilgeviciusA. Michailovas, “Kilohertz rate picosecond pulses amplifier for pumping of OPCPA system,” in Lasers, Sources, and Related Photonic Devices, Paper AW4A3, Optical Society of America (2012). Google Scholar

95. C. Heeseet al., “High-energy picosecond Nd:YVO4 slab amplifier for OPCPA pumping,” Appl. Phys. B 103(1), 5–8 (2011).APBOEM0946-2171 http://dx.doi.org/10.1007/s00340-011-4509-0 Google Scholar

96. A. Klenkeet al., “Coherently-combined two channel femtosecond fiber CPA system producing 3 mJ pulse energy,” Opt. Express 19(24), 24280–24285 (2011).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.19.024280 Google Scholar

97. T. Eidamet al., “Fiber chirped-pulse amplification system emitting 3.8 GW peak power,” Opt. Express 19(1), 255–260 (2011).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.19.000255 Google Scholar

98. D. E. Milleret al., “Sub-picosecond pulses at 100 W average power from a Yb:YLF chirped-pulse amplification system,” Opt. Lett. 37(13), 2700–2702 (2012).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.37.002700 Google Scholar

99. B. A. Reaganet al., “Demonstration of a 100 Hz repetition rate gain-saturated diode-pumped table-top soft x-ray laser,” Opt. Lett. 37(17), 3624–3626 (2012).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.37.003624 Google Scholar

100. G. H. Kimet al., “High average-power ultrafast CPA Yb:KYW laser system with dual-slab amplifier,” Opt. Express 20(4), 3434–3442 (2012).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.20.003434 Google Scholar

101. L. Daniaultet al., “High peak-power stretcher-free femtosecond fiber amplifier using passive spatio-temporal coherent combining,” Opt. Express 20(19), 21627–21634 (2012).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.20.021627 Google Scholar

102. J. Adamoniset al., “High-energy Nd:YAG-amplification system for OPCPA pumping,” Quantum Electron. 42(7), 567–574 (2012).QUELEZ1063-7818 http://dx.doi.org/10.1070/QE2012v042n07ABEH014689 Google Scholar

103. M. Lührmannet al., “High energy cw-diode pumped Nd:YVO4 regenerative amplifier with efficient second harmonic generation,” Opt. Express 17(25), 22761–22766 (2009).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.17.022761 Google Scholar

104. M. Schulzet al., “Pulsed operation of a high average power Yb:YAG thin-disk multipass amplifier,” Opt. Express 20(5), 5038–5043 (2012).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.20.005038 Google Scholar


Andreas Vaupel received the degrees diploma-physicist in 2008 from the Philipps University Marburg, Germany, and MS (optics) from the University of Central Florida in 2009. Currently, he is a graduate research assistant in CREOL at the University of Central Florida and expected to receive a PhD (optics) in 2013. He developed OPCPA and picosecond laser systems. As a visiting student at the University Bordeaux 1, France, he worked on high-power OPCPA systems and fiber-based lasers.

Nathan Bodnar received a BS degree (electrical engineering) and a MS degree (optics) from the University of Central Florida in 2010 and 2013, respectively. He is currently working as a graduate research assistant on his PhD degree in electrical engineering at the University of Central Florida. His research topics include novel methods in ultrafast laser development and EUV target control systems. He has extensive experience with the CEP stabilization of few-cycle OPCPA systems.

Benjamin Webb received a BS degree (electrical engineering) from Lamar University in 2009 and a MS degree (optics) from the University of Central Florida in 2011. He is currently a graduate research assistant in CREOL at the University of Central Florida. In 2013, he was awarded a graduate research excellence fellowship from the University of Central Florida. He works in the development of high-power ultrafast lasers using optical parametric chirped pulse amplification (OPCPA).

Lawrence Shah received his MS and PhD degrees (optical physics) from the University of Central Florida in 1999 and 2001, respectively. He has over 10 years experience in solid-state and fiber lasers, has been awarded seven patents and has authored many peer-reviewed publications. He leads the laser development efforts within LPL on Tm:fiber lasers, and Yb:thin-disk lasers. He also advises on the development of OPCPA lasers for the generation of high-intensity quasi-single-cycle optical pulses.

Martin Richardson graduated from Imperial College, London, (physics) and received a PhD (photon physics) from London University. Thereafter, he worked at the National Research Council Laboratories in Ottawa and joined the University of Rochester in 1980. In 1990, he established the LPL in CREOL at the University of Central Florida. He has held visiting scientific positions, published over 400 scientific articles in professional scientific journals, and presented numerous invited and plenary talks.

© The Authors. Published by SPIE under a Creative Commons Attribution 3.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.
Andreas Vaupel, Andreas Vaupel, Nathan Bodnar, Nathan Bodnar, Benjamin Webb, Benjamin Webb, Lawrence Shah, Lawrence Shah, Martin C. Richardson, Martin C. Richardson, } "Concepts, performance review, and prospects of table-top, few-cycle optical parametric chirped-pulse amplification," Optical Engineering 53(5), 051507 (31 December 2013). https://doi.org/10.1117/1.OE.53.5.051507 . Submission:

Back to Top