28 October 2014 Polarization-selective uncooled infrared sensor with asymmetric two-dimensional plasmonic absorber
Author Affiliations +
A polarization-selective uncooled infrared (IR) sensor was developed based on an asymmetric two-dimensional plasmonic absorber (2-D PLA). The 2-D PLA has an Au-based 2-D periodic dimple structure, where photons can be manipulated by spoof surface plasmon polaritons. Asymmetry was introduced into the 2-D PLA to realize a polarization selective function. Numerical investigations demonstrate that a 2-D PLA with ellipsoidal dimples (2-D PLA-E) gives rise to polarization-dependent absorption properties due to the asymmetric dimple shape. A microelectromechanical systems-based uncooled IR sensor was fabricated using a 2-D PLA-E through complementary metal oxide semiconductor (CMOS) and micromachining techniques. The 2-D PLA-E was formed with an Au layer sputtered on a SiO2 layer with ellipsoidal holes. The dependence of the responsivity on the polarization indicates that the responsivity is selectively enhanced according to the polarization and the asymmetry of the ellipsoids. The results provide direct evidence that a polarization-selective uncooled IR sensor can be realized simply by the introduction of asymmetry to the surface structure of the 2-D PLA, without the need for a polarizer or optical resonant structures. In addition, a pixel array where each pixel has a different detection polarization could be developed for polarimetric imaging using standard CMOS and micromachining techniques.



Infrared (IR) sensors are used to detect objects that emit IR radiation, and images can be constructed based on the IR intensity using pixel-array structures. Uncooled IR image sensors with a microelectromechanical (MEMS) system-based pixel structure possess significant advantages, such as low cost, ease of manufacture, and a wide range of applications.12.3

The authors are developing uncooled IR sensors with advanced functions to exploit their potential and expand their applications. For example, wavelength-selective uncooled IR sensors have recently been realized using a two-dimensional plasmonic absorber (2-D PLA) with wavelength selectivity in the middle and long wavelength IR regions.45.6 The 2-D PLA has a periodic array of circular dimples on its surface, where photons can be manipulated by spoof surface plasmon polaritons.78.9 The detection wavelength is determined by the reciprocal lattice vector of the 2-D PLA.10 The 2-D PLA has an advantage in that the detection wavelength can be controlled simply by the surface structure and without the need for filters,11,12 multilayer structures,13,14 or optical resonant structures.15,16 Such wavelength-selective uncooled IR sensors that employ plasmonics will contribute to the development of novel multicolor imaging for IR sensors.

Light has certain characteristics such as intensity, wavelength, polarization, and coherence, of which intensity and wavelength have been fully utilized for wavelength-selective uncooled IR sensors. As the next step, we have developed a polarization discrimination function for advanced uncooled IR sensors. Artificial objects, such as vehicles, buildings, roads, and agricultural fields, change the polarization state of the electromagnetic field reflected or emitted from their surfaces. Therefore, human influences can be distinguished from the natural environment on the Earth by polarimetric sensing.1718.19.20

A pixel array in which each pixel has a different absorption polarization angle could be used to realize polarimetric imaging at various IR wavelengths, which would provide a significant advantage for the detection of human influence in the environment. Therefore, polarization selectivity is a promising function for advanced IR sensing. A polarizer is often used to achieve polarimetric imaging;11,21 however, polarizers are very sensitive to the setting angle of the detector, which can cause optical loss, thus a rotating mechanical system is sometimes required. The attachment of such external optical systems requires additional space and increases the cost. Therefore, such approaches have difficulty with the integration of different pixels in an array for polarimetric imaging.

We have applied plasmonics to address this challenge. Plasmonics is a rapidly growing field of optical physics by which a metal surface structure provides the means for the manipulation of photons.22,23 We have previously reported that an Au-based 2-D concave structure can be used as a wavelength-selective absorber.4,5 However, the 2-D PLAs that have been developed have no polarization dependence. Asymmetry can be introduced to discriminate the polarization angle of the incident light. Thus, structural asymmetry is used to realize polarization-selective uncooled IR sensors based on an asymmetric 2-D PLA. We have recently reported that 2-D PLAs with elliptical dimples can produce polarization dependence.24 However, the detailed effect of the asymmetric shape of the elliptical dimples has not yet been reported. Thus, in this study, we provide a detailed report on the polarization selectivity of 2-D PLAs with elliptical dimples.



Our previous 2-D PLAs have symmetric lattice structures of circular dimples, such as square4,5 and triangular10 lattices, which provide no polarization dependence. Therefore, asymmetry was introduced to the 2-D PLA to realize polarization selectivity by changing the shape of the PLA dimples from circular to elliptical. The absorption properties of a 2-D PLA with ellipsoidal dimples (2-D PLA-E) indicate polarization dependence due to the asymmetric shape of the ellipse. Figure 1(a) shows a schematic illustration of the Au-based 2-D PLA-E used for the uncooled IR sensor and the definition of the polarization angle (θ) of the electrical field (E) with respect to the ellipse. Absorption is controlled by the filling factor, which is defined as the ratio between the diameter and the period of the dimples on the 2-D PLAs.6 The 2-D PLA-E has a periodic array of ellipsoidal dimples on its surface, where the ellipsoid shape introduces an asymmetric filling factor according to the major and the minor axes. Absorption can be selected according to these two axes to achieve polarization dependence.

Fig. 1

(a) Schematic diagram of the uncooled IR sensor (thermopile) with Au-based two-dimensional plasmonic absorber (2-D PLA) having ellipsoidal dimples, and definition of the electric field polarization angle to the axis of the ellipsoid. (b) Calculated polarization dependence for the 2-D PLA-E. (c) Concept of a pixel array with various 2-D PLA-Es for polarimetric imaging.


Figure 1(b) shows the calculated polarization dependence for the absorption of the Au-based 2-D PLA-E with a fixed dimple period (P) of 6.0μm, a major axis of 3.0μm, a minor axis of 1.5μm, and a depth of 1.0μm for comparison with the 2-D PLA having circular dimples.4,5 The wavelength was normalized according to P. The strong polarization dependence of the absorption is evident according to θ. When E is vertical to the major axis (θ=90deg), sufficient absorption is obtained; however, when E is parallel to the major axis (θ=0deg), there is no absorption. The absorption increases with to the increase of θ, which satisfies the requirements for an uncooled wideband IR sensor with a polarization-selective function. Thus, theoretical calculations demonstrated that the elliptical shape produces polarization dependence.

Figure 1(c) shows the concept of the array structure for 2-D PLA-Es with polarization discrimination. One unit consists of four pixels and 2-D PLA-Es when different absorptions at θ of 0, 45, 90, and 135 deg are employed. Polarimetric imaging can thus be realized by introducing asymmetry to the surface structure.


Sensor Fabrication

A MEMS-based uncooled IR sensor with 2-D PLA-Es was developed. The 2-D PLA-Es are fabricated by forming an Au layer on a perforated SiO2 substrate. Figure 2 shows the procedure used to fabricate the MEMS-based thermopile with a 2-D PLA-E. (a) The devices are fabricated on 6-in. p-type Si(100) substrates using a standard complementary metal oxide semiconductor (CMOS) process. The thermocouples consist of a series of p- and n-type polycrystalline Si regions, of which the resistivity is controlled by ion implantation. An Al layer is formed as a backside reflective layer under the absorber area. Etching holes for bulk micromachining are formed by reactive-ion etching (RIE). A 1.5-μm-thick SiO2 layer is formed on the absorber area. (b) The periodic ellipsoidal dimple structures are then formed only on the SiO2 layer of the IR absorber area by RIE. (c) 50/250-nm-thick Cr/Au layers are sputtered, where the Cr layer acts as an adhesion layer between SiO2 and Au. The 250-nm-thick Au layer is sufficiently thicker than the skin depth in the IR wavelength region.25 Incident IR rays cannot penetrate the Au film, so that absorption by SiO2 beneath the Au layer is negligible.5 The Cr/Au layers are selectively etched using a wet etchant to reveal etching holes covered by the sputtered layers. Scanning electron microscopy (SEM) observation confirmed that the Cr/Au layers were uniformly coated on both the bottom and side walls of the etched holes and the concave Au structures were completed. (d) The wafers are diced into chips. Si is anisotropically etched through the etching holes using tetramethylammonium hydroxide (TMAH). The cavity under the IR absorber area is then formed, which results in the completion of a thermally isolated freestanding structure on which the 2-D PLA-E absorber is formed. The backside and edge of the 2-D PLA-E was coated with Au and Al to prevent absorption by SiO2.

Fig. 2

Schematic diagram of the procedure used to fabricate the microelectromechanical system (MEMS)-based thermopile with 2-D PLA-E. (a) Devices are formed on the surface of a SiO2/Si wafer by a standard complementary metal oxide semiconductor process. Etching holes are formed by reactive-ion etching. (b) The periodic hole structures are formed on SiO2 using a dry etching process. (c) Cr/Au layers are sputtered on the perforated SiO2/Si substrate. (d) The thermally isolated freestanding structure is completed by bulk micromachining.


Figure 3(a) shows an SEM image of one of the developed thermopiles with the 2-D PLA-E. The detector area (300×200μm2) is surrounded by long thermal isolation legs to reduce thermal conductance. Various sensors with different 2-D PLA-E structures were fabricated on the same wafer. The length of the major axis, the period and the depth of the dimples were fixed at 4.0, 5.0, and 1.5μm for all sensors, respectively, considering the resolution limit of the photolithography system employed. The length of the minor axis was changed and the ellipticity was defined as the ratio of the minor axis length to that of the major axis of the ellipsoid. The respective minor axis lengths of the ellipsoids and the ellipticity were (i) 4.0μm and 100%, (ii) 3.0μm and 75%, (iii) 2.5μm and 62.5%, (iv) 2.0μm and 50%, and (v) 1.5μm and 37.5%. Sensor (i) has circular dimples and acts as a reference for comparison. Figure 3(b) shows a magnified SEM image of the 2-D PLA-E sensor (iv) surface, and Fig. 3(c) shows a schematic diagram of the 2-D PLA-E. The top surface of the Au layer acts as an absorption layer. The bottom Al layer prevents backside absorption by the SiO2 substrate.

Fig. 3

(a) Scanning electron microscopy (SEM) image of the MEMS-based thermopile with 2-D PLA-E developed in this study. (b) Magnified SEM images of the 2-D PLA-E of sensor (iv). (c) Schematic diagram of the 2-D PLA-E.




Figure 4 shows a schematic diagram of the experimental setup used to measure the polarization dependence of the 2-D PLA-E. The sensors were set in a vacuum chamber with a BaF2 window under a pressure of 1 Pa to prevent thermal conduction loss through the atmosphere. IR radiation from a blackbody was irradiated to the sample through narrow bandpass filters for selection of the evaluation wavelengths. The typical full width at half maximum was 80 nm. A polarizer was set in front of the BaF2 window and a pinhole was used to restrict the incident light to the 2-D PLA. The polarization angle was defined as shown in Fig. 1(b).

Fig. 4

Schematic diagram of experimental setup used for polarization dependence measurements.


Figure 5 shows the normalized responsivity of sensors (i) to (v) for θ=0deg and 90 deg. The responsivity was normalized with respect to the responsivity peak of each sensor to investigate the polarization dependence according to the ellipticity. Sensor (i) with circular dimples has no polarization dependence due to its symmetry. When the incident polarization is vertical to the major axis (θ=90deg), the responsivity is clearly enhanced for sensors (ii) to (v). In contrast, the responsivity for parallel polarization (θ=0deg) was clearly suppressed according to the decrease of the ellipticity. The measured polarization properties agree well with the calculated results, as shown in Fig. 1(b). Thus, the responsivity is selectively enhanced according to the asymmetric shape of the ellipsoids.

Fig. 5

Measured polarization dependence of the spectral responsivity at θ=0deg and 90 deg for sensors (i) to (v).


Figure 6 shows the relation between the extinction ratio and the ellipticity. The extinction ratio is defined as the ratio of responsivity of the electric field at θ=0deg to that at θ=90deg. The responsivity at θ=90deg for the extinction ratio was adopted as the peak wavelength. The responsivity at θ=0deg was adopted as the peak wavelength for sensors (i) to (iii) and the wavelength corresponding to the peak at θ=90deg was adopted for sensors (iv) and (v), due to the lack of a clear peak at the main detection wavelength. Figure 6 shows that the extinction ratio decreased with the ellipticity.

Fig. 6

Extinction ratio as a function of the ellipticity.




A MEMS-based uncooled IR sensor with 2-D PLA-Es was developed using standard CMOS and micromachining techniques. The polarization dependence of the responsivity demonstrates that the enhancement of the selective responsivity according to the polarization angle was successfully achieved and that polarization dependence can be controlled simply with the ellipticity. These results are direct evidence that a polarization-selective uncooled IR sensor can be realized simply by the introduction of asymmetry to the 2-D PLA surface structure, without the need for polarizers or filters. Control of the detection polarization using asymmetric PLAs could be applied to other types of thermal IR sensors, such as bolometers and silicon-on-insulator diodes.26 The results obtained here will contribute to the development of novel polarimetric imaging for IR sensors.


The authors thank Mitsuharu Uetsuki, Daisuke Fujisawa, Masashi Ueno, Tetsuya Satake, Katsuhiko Tsujino and Tetsuji Sorita of the Advanced Technology R&D Center of Mitsubishi Electric Corporation for helpful support.


1. P. W. Kruse, Uncooled Thermal Imaging Arrays, Systems, and Applications, SPIE, Bellingham, Washington (2001). Google Scholar

2. M. VollmerK.-P. Mollmann, Infrared Thermal Imaging: Fundamentals, Research and Applications, Wiley-VCH, Weinheim (2010). Google Scholar

3. M. Kimata, “Trends in small-format infrared array sensors,” in 2013 IEEE Proc. Sensors, pp. 1–4, IEEE (2013). Google Scholar

4. S. Ogawaet al., “Wavelength selective uncooled infrared sensor by plasmonics,” Appl. Phys. Lett. 100(2), 021111 (2012).APPLAB0003-6951 http://dx.doi.org/10.1063/1.3673856 Google Scholar

5. S. Ogawaet al., “Wavelength selective wideband uncooled infrared sensor using a two-dimensional plasmonic absorber,” Opt. Eng. 52(12), 127104 (2013).OPEGAR0091-3286 http://dx.doi.org/10.1117/1.OE.52.12.127104 Google Scholar

6. K. Masudaet al., “Optimization of two-dimensional plasmonic absorbers based on a metamaterial and cylindrical cavity model approach for high-responsivity wavelength-selective uncooled infrared sensors,” Sens. Mater. 26(4), 215–223 (2014).SENMER0914-4935 Google Scholar

7. J. B. PendryL. Martin-MorenoF. J. Garcia-Vidal, “Mimicking surface plasmons with structured surfaces,” Science 305(5685), 847–848 (2004).SCIEAS0036-8075 http://dx.doi.org/10.1126/science.1098999 Google Scholar

8. F. J. Garcia-VidalL. Martín-MorenoJ. B. Pendry, “Surfaces with holes in them: new plasmonic metamaterials,” J. Optic. A: Pure Appl. Opt. 7(2), 5 (2005).JOAOF81464-4258 http://dx.doi.org/10.1088/1464-4258/7/2/013 Google Scholar

9. R. Stanley, “Plasmonics in the mid-infrared,” Nat. Photonics 6(7), 3 (2012).1749-4885 http://dx.doi.org/10.1038/nphoton.2012.161 Google Scholar

10. S. Ogawaet al., “Wavelength selective uncooled infrared sensor using triangular-lattice plasmonic absorbers,” in 2013 Int. Conf. on Proc. Optical MEMS and Nanophotonics (OMN), pp. 61–62, IEEE (2013). Google Scholar

11. R. Haïdaret al., “Free-standing subwavelength metallic gratings for snapshot multispectral imaging,” Appl. Phys. Lett. 96(22), 221104 (2010).APPLAB0003-6951 http://dx.doi.org/10.1063/1.3442487 Google Scholar

12. Y. OhteraH. Yamada, “Photonic crystals for the application to spectrometers and wavelength filters,” IEICE Elec. Exp. 10(8), 20132001 (2013).1349-2543 http://dx.doi.org/10.1587/elex.10.20132001 Google Scholar

13. T. MaierH. Brueckl, “Multispectral microbolometers for the midinfrared,” Opt. Lett. 35(22), 3766–3768 (2010).OPLEDP0146-9592 http://dx.doi.org/10.1364/OL.35.003766 Google Scholar

14. N. Landyet al., “Perfect metamaterial absorber,” Phys. Rev. Lett. 100(20), 207402 (2008).PRLTAO0031-9007 http://dx.doi.org/10.1103/PhysRevLett.100.207402 Google Scholar

15. S. W. Hanet al., “Design of infrared wavelength-selective microbolometers using planar multimode detectors,” Electron. Lett. 40(22), 1410–1411 (2004).ELLEAK0013-5194 http://dx.doi.org/10.1049/el:20046547 Google Scholar

16. R. P. SheaA. S. GawarikarJ. J. Talghader, “Midwave thermal infrared detection using semiconductor selective absorption,” Opt. Exp. 18(22), 22833–22841 (2010).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.18.022833 Google Scholar

17. J. R. Schott, Fundamentals of Polarimetric Remote Sensing, SPIE, Bellingham, Washington (2009). Google Scholar

18. J. S. Tyoet al., “Review of passive imaging polarimetry for remote sensing applications,” Appl. Opt. 45(22), 5453–5469 (2006).APOPAI0003-6935 http://dx.doi.org/10.1364/AO.45.005453 Google Scholar

19. J. S. Tyoet al., “The effects of thermal equilibrium and contrast in LWIR polarimetric images,” Opt. Exp. 15(23), 15161–15167 (2007).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.15.015161 Google Scholar

20. B. M. RatliffC. F. LaCasseJ. S. Tyo, “Interpolation strategies for reducing IFOV artifacts in microgrid polarimeter imagery,” Opt. Exp. 17(11), 9112–9125 (2009).OPEXFF1094-4087 http://dx.doi.org/10.1364/OE.17.009112 Google Scholar

21. G. W. Kamermanet al., “Polarization state imaging in long-wave infrared for object detection,” Proc. SPIE 8897, 88970R (2013).PSISDG0277-786X http://dx.doi.org/10.1117/12.2028858 Google Scholar

22. D. K. GramotnevS. I. Bozhevolnyi, “Plasmonics beyond the diffraction limit,” Nat. Photonics 4(2), 83–91 (2010).1749-4885 http://dx.doi.org/10.1038/nphoton.2009.282 Google Scholar

23. S. Kawata, “Plasmonics: future outlook,” Jpn. J. Appl. Phys. 52(1), 010001 (2013).JJAPA50021-4922 http://dx.doi.org/10.7567/JJAP.52.010001 Google Scholar

24. S. Ogawaet al., “Polarization selective uncooled infrared sensor using an asymmetric two-dimensional plasmonic absorber,” Proc. SPIE 9070, 90701T (2014).PSISDG0277-786X http://dx.doi.org/10.1117/12.2049677 Google Scholar

25. F. Neubrechet al., “Properties of gold nanoantennas in the infrared,” in Chapter 12 in Nanostructures in Electronics and Photonics, F. Rahman, Ed., p. 210, World Scientific Publishing Co., Singapore (2008). Google Scholar

26. D. Fujisawaet al., “Two-million-pixel SOI diode uncooled IRFPA with 15μm pixel pitch,” Proc. SPIE 8353, 83531G (2012).PSISDG0277-786X http://dx.doi.org/10.1117/12.919520 Google Scholar


Shinpei Ogawa received his BE, ME, and PhD degrees from the Department of Electronic Science and Engineering, Kyoto University, Japan, in 2000, 2002, and 2005, respectively. He has been with the Advanced Technology R&D Center, Mitsubishi Electric Corporation, Amagasaki, Japan, since 2005. He works on the development of various MEMS devices, including RF-MEMS switches, inductors, TSV, optical sensors, infrared sensors, and packaging technology. His current research interests are photonic and plasmonic devices integrated with MEMS technology.

Kyohei Masuda received his BE and ME degrees from the College of Science and Engineering, Ritsumeikan University, Japan, in 2012 and 2014, respectively.

Yousuke Takagawa received his BE degree from the College of Science and Engineering, Ritsumeikan University, Japan, in 2013. He is currently working for his ME degree in the College of Science and Engineering, Ritsumeikan University.

Masafumi Kimata received his MS degree from Nagoya University in 1976, and received his PhD degree from Osaka University in 1992. He joined Mitsubishi Electric Corporation in 1976 and retired from Mitsubishi Electric in 2004. Currently, he is a professor of Ristumeikai University, where he continues his research on MEMS-based uncooled infrared focal plane arrays and type-II superlattice infrared focal plane arrays. He is a Fellow of SPIE.

© The Authors. Published by SPIE under a Creative Commons Attribution 3.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.
Shinpei Ogawa, Shinpei Ogawa, Kyohei Masuda, Kyohei Masuda, Yousuke Takagawa, Yousuke Takagawa, Masafumi Kimata, Masafumi Kimata, } "Polarization-selective uncooled infrared sensor with asymmetric two-dimensional plasmonic absorber," Optical Engineering 53(10), 107110 (28 October 2014). https://doi.org/10.1117/1.OE.53.10.107110 . Submission:

Back to Top