In this paper, a two-element sensor of relative humidity of a parallel structure is proposed for consideration, which differs from the existing ones by using address fiber Bragg gratings made in SMF-28 fiber. One of the grids has a quartz shell replaced by polyimide, synthesized using a fiber coating with a full multiplicative response to temperature and deformation caused by humidity. The second grating recorded in a standard fiber and responds to temperature. It is possible to include an additional third grating with a partially etched cladding, which can be used for refract metric measurements of the amount of condensed moisture on the elements of a complete switchgear. All gratings are identical, have the same Bragg wavelength, after manipulating their claddings, but differ in a unique address, which is formed by recording two transparency windows in each of the gratings with different difference frequency space. The transparency windows correspond to phase π-shifts symmetrically located at the same distance from the center of each of the gratings. The structure obtained makes it possible to record information of the measurement conversion at the indicated difference frequencies in the radio range, which significantly increases the speed of measurements of relative humidity and their accuracy by an order of magnitude. In addition to what has been said, it is possible to note the possibility of building a network of these sensors in consecutively arranged switchgear devices, with a different radiofrequency address group being used in each of them.
This work presents fast and simple method for estimation of the insertion loss at the connection of two singlemode optical fibers with contaminated fiber optic connector ferrule end faces. Proposed solution is based on the fundamental mode coupling coefficient (or e.g. transmission coefficient) evaluation via discretized mode field overlap integral. It is represented in the form of nested sums on radial mode field distributions, which are described well by Gaussian function under weakly guiding approximation or may be taken from the mode field distribution matrix, computed by rigorous numerical methods during analysis of real optical fiber samples with nonsymmetrical geometry. Proposed approach provides ability of taking into account the mode field distortions, occurring due to end face contaminations, by directly overlapping of connector ferrule end face image over discretized mode field radial distribution. We present some results of developed method approbation on really measured fiber optic connections between standard singlemode optical fibers with various order contaminated ferrules.
This work presents an alternative method implemented in software procedure for automated localization of fiber optic connector contaminated ferrule end face image artifacts. Here the main problem is concerned with detection and removing the aureoles of core/cladding and cladding/ferrule boundaries without impact on pixels of contamination particles. We considered typical end face images measured by commercially available fiber optic video probe kit containing video microscope and software, which provides ferrule end-face quality inspection "PASS/FAIL" according to ratified standard IEC 61300-3-35 that is a global common set of quality requirements for the surface of ferrule fiber optic connectors. After removing artifacts, modified image may be utilized for the following estimation of the predicted value of insertion loss. We also present some results of proposed procedure approbation for various order contaminated ferrule end face images.
This work presents some results of experimental approbation of method for writing of cascaded precision microstructured defects, like "tapers" and "up-tapers", in various configurations and sequences in silica multimode graded index optical fibers by commercially available field fusion splicer with modified software settings. Here we utilized earlier on developed technique for micro-defect geometry parameters estimation via analysis of photo-image, performed after defect writing and displayed on fusion splicer screen, to estimate the least available distance between couples of the “up-tapers” and “tapers” without optical fiber structure deformation. Also, some results of insertion loss measurements for various configuration of 3-element cascaded microstrucured defects are presented.
This work presents results of experimental approbation of earlier on proposed modified fiber optic stress sensor based on a few-mode effects occurring during laser-excited optical signal propagation over silica multimode optical fiber (MMF). Modification is concerned with a passage to quasi-interferometric scheme realized by two multimode Y-couplers with equalized arm lengths improved by fiber Bragg grating (FBG) written on preliminary formed precision macrostructure defects in silica multimode graded-index optical fibers and special offset launching conditions providing laser-based excitation of higher-order modes. The “arms” of quasi-interferometer are two equalized lengths of MMF Cat. OM2 with great central dip of refractive index profile and strong pulse splitting due to high differential mode delay (DMD). We tested FBGs with Bragg wavelength both 1310 nm and 1550 nm written over tapers or up-tapers preliminary formed in short pieces of MMF Cat. OM2+/OM3 and further jointed to the end of one of the arms before output Y-coupler. Researches were focused on comparison analysis of pulse responses under changing of selected excited mode mixing and power diffusion processes due to stress distributed action to sensor fiber depending. Here we considered FBGs not only as particular wavelength reflector during spectral response measurement but also as local periodic microstructure defect which strongly effects on few-mode signal components mixing process also improved by combination with macro-defect like taper or up-taper that should provide response variation. Some results pulse response measurements produced for different scheme configuration and their comparison analysis are represented.
This work presents method for performing precision macro-structure defects “tapers” and “up-tapers” written in conventional silica telecommunication multimode optical fibers by commercially available field fusion splicer with modified software settings and following writing fiber Bragg gratings over or near them. We developed technique for macrodefect geometry parameters estimation via analysis of photo-image performed after defect writing and displayed on fusion splicer screen. Some research results of defect geometry dependence on fusion current and fusion time values re-set in splicer program are represented that provided ability to choose their “the best” combination. Also experimental statistical researches concerned with “taper” and “up-taper” diameter stability as well as their insertion loss values during their writing under fixed corrected splicer program parameters were performed. We developed technique for FBG writing over or near macro-structure defect. Some results of spectral response measurements produced for short-length samples of multimode optical fiber with fiber Bragg gratings written over and near macro-defects prepared by using proposed technique are presented.
This work is concerned with fiber Bragg grating (FBG) writing technique developed for graded-index multimode optical fibers applied in measurement systems based on a few-mode effects. We present some results of experimental approbation of proposed technique with Bragg wavelength 1310 and 1550 nm on samples of graded-index multimode optical fibers 50/125 of both new-generations Cat. OM2+/OM3 and old Cat. OM2 with preliminary measured refractive index profiles. While the first group fibers of Cat. OM2+/OM3 was characterized by almost ideal smooth graded refractive index profile and some fiber profile samples of this group contains thin central peak, the second fiber group profiles of Cat. OM2 differ by great central core defects representing dip or thick peak. Results of described FBG spectral response measurements under excitation of laser pigtailed by single-mode fiber are represented.
This work presents results of experimental approbation of modified fiber optic stress sensor based on a few-mode effects
occurring during laser-excited optical signal propagation over silica multimode optical fiber (MMF). Modification is
concerned with adding of quasi-interferometric scheme realized by two multimode Y-couplers with equalized arm
lengths improved by fiber Bragg grating (FBG) and special offset launching conditions providing laser-based excitation
of higher-order modes. We tested FBGs written on graded-index MMFs 50/125 with Bragg wavelength 1550 nm connected
to different parts of proposed scheme. Researches are focused on comparing analysis of both spectral and pulse
responses under changing of selected mode mixing and power diffusion processes due to stress local and distributed action
to sensor fiber depending on scheme configuration. Here we considered FBGs not only as particular wavelength
reflector during spectral response measurement but also as local periodic microstructure defect strongly effecting few-mode
signal components mixing process that provides pulse response variation. Some results of spectral and pulse response
measurements produced for different scheme configuration and their comparison analysis are represented.
This work presents results of experimental researches of fiber Bragg gratings (FBG) operating in a few-mode regime.
We tested FBGs written on silica graded-index multimode fibers 50/125 Cat. OM2+/OM3 with Bragg wavelength 1550
nm by using them in a set of developed experimental schemes based on excitation of multimode fibers by corresponding
laser sources. The researches were focused on analysis of both spectral and pulse responses under changing of selected
mode mixing and power diffusion processes due to tension and/or stress local and distributed action to FBG or sensor
fiber. Results of spectral and pulse response measurements at the output of schemes with installed described FBGs are
represented.
This paper presents a microwave photonics method for the instantaneous frequency measurement of microwave signals,
based on the generation of a two-frequency laser radiation in the Mach-Zehnder modulator with a difference frequency
equal to the measured, and the "frequency - amplitude" conversion in the π-phase-shifted fiber Bragg grating. Frequency
measurement occurs in two ranges: 0.3 - 3 GHz in the passband of the FBG and 3 - 30 GHz in its reflection band. Using
the specific conversion of two-frequency radiation in the π-phase-shifted fiber Bragg grating allowed us to obtain measuring
characteristics, that are independent of the amplitude fluctuations of the optical carrier and to organize additional
circuit for monitoring the spectral characteristics of the used elements to reduce measurement inaccuracy caused by their
temperature instability.
This paper presents a new two-frequency method for the instantaneous frequency and amplitude measurement of unknown microwave signal. Using the specific interaction of two-frequency radiation with fiber Bragg grating (FBG) in first version and FBG with phase π-shift in second allowed us to obtain measuring characteristics, that are independent of the energy fluctuations of the optical carrier and the microwave signal. Frequency measurement occurs in two ranges: 3-30 GHz in FBG reflection band, and in second version 0,3-3 GHz in the FBG pass band. Additional circuit for spectral characteristics monitoring of the used elements are organized to reduce measurement inaccuracy caused by their temperature instability.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print format on
SPIE.org.