In this work, we discuss the verification and preliminary experimental characterization of a MEMS-based vibration Energy Harvester (EH) design. The device, named Four-Leaf Clover (FLC), is based on a circular-shaped mechanical resonator with four petal-like mass-spring cascaded systems. This solution introduces several mechanical Degrees of Freedom (DOFs), and therefore enables multiple resonant modes and deformation shapes in the vibrations frequency range of interest. The target is to realize a wideband multi-modal EH-MEMS device, that overcomes the typical narrowband working characteristics of standard cantilevered EHs, by ensuring flexible and adaptable power source to ultra-low power electronics for integrated remote sensing nodes (e.g. Wireless Sensor Networks – WSNs) in the Internet of Things (IoT) scenario, aiming to self-powered and energy autonomous smart systems. Finite Element Method simulations of the FLC EH-MEMS show the presence of several resonant modes for vibrations up to 4-5 kHz, and level of converted power up to a few μW at resonance and in closed-loop conditions (i.e. with resistive load). On the other hand, the first experimental tests of FLC fabricated samples, conducted with a Laser Doppler Vibrometer (LDV), proved the presence of several resonant modes, and allowed to validate the accuracy of the FEM modeling method. Such a good accordance holds validity for what concerns the coupled field behavior of the FLC EH-MEMS, as well. Both measurements and simulations performed at 190 Hz (i.e. out of resonance) showed the generation of power in the range of nW (Root Mean Square – RMS values). Further steps of this work will include the experimental characterization in a full range of vibrations, aiming to prove the whole functionality of the FLC EH-MEMS proposed design concept.
Thermal cycling test are part of the standard space qualification procedure for RF-MEMS devices. Standardized tests are rather demanding in terms of equipment and experimental time. In this paper we present a fast thermal cycling test aimed at obtaining a rapid selection among different switch geometries in terms of thermal cycling resistance. Seven different switch typologies are examined and tested, evidencing that the most important source of deterioration is the mechanical deformation of the movable membrane. The principal characteristic found in the most resistant typologies is a more uniform distribution of the thermal strain over the whole membrane. To this respect, a careful design of the membrane anchors is extremely important for achieving a good thermal cycling resistance.
<p> Energy Harvesters (EH) are devices that convert environmental energy (i.e. thermal, vibrational, solar or electromagnetic) into electrical energy. One of the most promising solutions consists in transforming energy from vibrations using a piezoelectric material placed onto a mechanical resonator. The intrinsic drawback of this solution is the typically high quality factor of the device and so the device works effectively only within a narrow bandwidth. To overcome this limitation it is possible to tune the mechanical resonance of the device, to introduce non-linear elements (e.g. magnets) or to design the mechanical resonator with a multimodal behavior. In Ultra Low Power (ULP) applications the aspect of integration is of utmost importance and so MEMS-based (micro electro-mechanical systems) EHs are preferable. Within this scenario the multimodal solution is the more suitable considering the technological constraints imposed by the micro machining manufacturing process. </p><p> In this paper we optimize a given multimodal mechanical geometry in order to maximize the number of resonances within a certain frequency band. In the particular case of piezoelectric energy harvesting, the strain distribution of each modes is critical and has to be taken into consideration for the designing of efficient device. The proposed optimization is FEM-based and it uses modal and harmonic simulations for both select the useful modes and then to design the device in a way that presents those modes within a predefined frequency range. This mechanical optimization could be considered the first step for maximizing the output power of a multimodal piezoelectric energy harvester. The second step focuses on the geometry optimization of the piezoelectric transducer element, starting from the desired resonant mode configuration defined in the first stage. The number of modes stimulated applying a vertical acceleration increases in number in the desired frequency range (i.e. around 1 kHz). As the output power is proportional to the stress of the flexible device, these promising results show clearly how an optimization of the geometry could significantly boost the performance of such devices. </p>
In this work, we discuss a novel mechanical resonator design for the realization of vibration Energy Harvester (EH) capable to deliver power levels in the mW range. The device overcomes the typical constraint of frequency narrowband operability of standard cantilevered EHs, by exploiting a circular-shaped resonator with an increased number of mechanical Degrees Of Freedom (DOFs), leading to several resonant modes in the range of vibrations of interest (i.e. multi-modal wideband EH). The device, named Four-Leaf Clover (FLC), is simulated in Ansys Worbench™, showing a significant number of resonant modes up to vibrations of around 2 kHz (modal eigenfrequencies analysis), and exhibiting levels of converted power up to a few mW at resonance (harmonic coupled-field analysis). The sole FLC mechanical structure is realized by micro-milling an Aluminum foil, while a cantilevered test structure also including PolyVinyliDene Fluoride (PVDF) film sheet is assembled in order to collect first experimental feedback on generated power levels. The first lab based tests show peak-to-peak voltages of several Volts when the cantilever is stimulated with a mechanical pulse. Further developments of this work will comprise the assembly of an FLC demonstrator with PVDF pads, and its experimental testing in order to validate the simulated results.
In the last decade Micro-Electro-Mechanical Systems (MEMS) technology experienced a significant development in
various fields of Information and Communication Technology (ICT). In particular MEMS for Radio Frequency (RF)
applications have emerged as a remarkable solution in order to fabricate components with outstanding performances.
The encapsulation of such devices is a relevant aspect to be addressed in order to enable wide exploitation of RF-MEMS
technology in commercial applications. A MEMS package must not only protect fragile mechanical parts but also
provide the interface to the next level of the packaging hierarchy in a cost effective technology. Additionally, in RF
applications the electromagnetic impact of the package has to be carefully considered.
Given such a scenario, the focus of this work is the characterization of a chip capping solution for RF-MEMS devices.
Such solution uses a quartz cap having an epoxy-based dry film sealing ring. Relevant issues affecting RF-MEMS
devices once packaged, e.g. the mechanical strain induced by the cap and the hermeticity of the sealing ring, are worth
investigating. This work focuses on the study of induced strain, as a function of different bonding parameters.
Dimensional features of the sealing ring (i.e. the width), and process parameters, like temperature and pressure, have
The package characterization is performed by using basic test vehicles, such as strain gauges, designed to be integrated
inside the internal cavity of the package itself. Polysilicon piezoresistors are used as strain gauges, whereas aluminum
resistors are used as thermometers to assess the impact of temperature changes on strain measurements. Experimental
data are reported including calibration of the sensors as well as environmental measurements with and without cap. In
addition measurements of the shear stress of the proposed packaging solution are also reported.