Compacting devices is an increasingly demanding requirement for many applications in both nonimaging and imaging optics. “Compacting” means here decreasing the volume of the space between the entry and the exit aperture without decreasing the optical performance. For nonimaging optical systems, compact optics is mainly important for reducing cost. Its small volume means less material is needed for mass-production and small size and light weight save cost in transportation. For imaging optical systems, in addition to the mentioned advantages, compact optics increases portability of devices as well, which contributes a lot to wearable display technologies such as Head Mounted Displays (HMD). After reviewing the different techniques to design compact systems, we analyze here the multichannel strategies. These type of designs split the incoming bundle of rays in different sub-bundles that are optically processed (independently) and then recombined in a single outgoing bundle. The optics volume decreases rapidly with the number of sub-bundles. These designs usually need to be combined with freeform optics in order to get optimum performance.
Recent advances in the Simultaneous Multiple Surfaces (SMS) design method are reviewed in this paper. In particular,
we review the design of diffractive surfaces using the SMS method and the concept of freeform aplanatism as a limit
case of a 3D SMS design.
The Simultaneous Multiple Surface (SMS) method was initially developed as a design method in Nonimaging Optics and later, the method was extended for designing Imaging Optics. We show an extension of the SMS method to diffractive surfaces. Using this method, diffractive kinoform surfaces are calculated simultaneously and through a direct method, i. e. it is not based in multi-parametric optimization techniques. Using the phase-shift properties of diffractive surfaces as an extra degree of freedom, only N/2 surfaces are needed to perfectly couple N one parameter wavefronts. Wavefronts of different wavelengths can also be coupled, hence chromatic aberration can be corrected in SMS-based systems. This method can be used by combining and calculating simultaneously both reflective, refractive and diffractive surfaces, through direct calculation of phase and refractive/reflective profiles. Representative diffractive systems designed by the SMS method are presented.
The Simultaneous Multiple Surface (SMS) method was initially developed as a design method in Nonimaging Optics and later, the method was extended for designing Imaging Optics. We present the extension of the SMS method to design diffractive optical surfaces. This method involves the simultaneous calculation of N/2 diffractive surfaces, using the phase-shift properties of diffractive surfaces as an extra degree of freedom, such that N one-parameter wavefronts can be perfectly coupled. Moreover, the SMS method for diffractive surfaces is a direct method, i.e., it is not based in multi-parametric optimization techniques. Representative diffractive systems designed by the SMS method are presented.
The field of concentrated photovoltaics (CPV) has met some remarkable advances in recent years. The continuous increase in conversion efficiency of multijunction solar cells and new advancements in optics have led to new demands and opportunities for optical design in CPV. This paper is a mini-review on current requirements for CPV optical design, and it presents some of the main trends in recent years on CPV systems architecture.
Non-uniform irradiance patterns created by Concentrated Photovoltaics (CPV) concentrators over Multi-Junction Cells (MJC) can originate significant power losses, especially when there are different spectral irradiance distributions over the different MJC junctions. This fact has an increased importance considering the recent advances in 4 and 5 junction cells. This work presents a new CPV optical design, the 9-fold Fresnel Köhler concentrator, prepared to overcome these effects at high concentrations while maintaining a large acceptance angle, paving the way for a future generation of high efficiency CPV systems of 4 and 5 junction cells.
Non-uniform irradiance patterns created by Concentrated Photovoltaics (CPV) concentrators over Multi-Junction Cells (MJC) can originate significant power losses, especially when there are different spectral irradiance distributions over the different MJC junctions. This fact has an increased importance considering the recent advances in 4 and 5 junction cells. The spectral irradiance distributions are especially affected with thermal effects on Silicone-on-Glass (SoG) CPV systems. This work presents a new CPV optical design, the 9-fold Fresnel Köhler concentrator, prepared to overcome these effects at high concentrations while maintaining a large acceptance angle, paving the way for a future generation of high efficiency CPV systems of 4 and 5 junction cells.
In order to have a cost-effective CPV system, two key issues must be ensured: high concentration factor and high tolerance. The novel concentrator we are presenting, the dome-shaped Fresnel-Köhler, can widely fulfill these two and other essential issues in a CPV module. This concentrator is based on two previous successful CPV designs: the FK concentrator with a flat Fresnel lens and the dome-shaped Fresnel lens system developed by Daido Steel, resulting on a superior concentrator. The concentrator has shown outstanding simulation results, achieving an effective concentration-acceptance product (CAP) value of 0.72, and an optical efficiency of 85% on-axis (no anti-reflective coating has been used). Moreover, Köhler integration provides good irradiance uniformity on the cell surface and low spectral aberration of this irradiance. This ensures an optimal performance of the solar cell, maximizing its efficiency. Besides, the domeshaped FK shows optimal results for very compact designs, especially in the f/0.7-1.0 range. The dome-shaped Fresnel- Köhler concentrator, natural and enhanced evolution of the flat FK concentrator, is a cost-effective CPV optical design, mainly due to its high tolerances. Daido Steel advanced technique for demolding injected plastic pieces will allow for easy manufacture of the dome-shaped POE of DFK concentrator.
A new design for a photovoltaic concentrator, the most recent advance based on the Kohler concept, is presented. The
system is mirror-based, and with geometry that guaranties a maximum sunlight collection area (without shadows, like
those caused by secondary stages or receivers and heat-sinks in other mirror-based systems). Designed for a concentration of 1000x, this off axis system combines both good acceptance angle and good irradiance uniformity on the solar cell. The advanced performance features (concentration-acceptance products –CAP- about 0.73 and affordable peak and average irradiances) are achieved through the combination of four reflective folds combined
with four refractive surfaces, all of them free-form, performing Köhler integration 2. In Köhler devices, the irradiance uniformity is not achieved through additional optical stages (TIR prisms), thus no complex/expensive elements to manufacture are required. The rim angle and geometry are such that the secondary stage and receivers are hidden below the primary mirrors, so maximum collection is assured. The entire system was designed to allow loose assembly/alignment tolerances (through high acceptance angle) and to be manufactured using already well-developed methods for mass production, with high potential for low cost. The optical surfaces for Köhler integration, although with a quite different optical behavior, have approximately the same dimensions and can be manufactured with the same techniques as the more traditional secondary optical elements used for concentration (typically plastic injection molding or glass molding). This paper will show the main design features, along with realistic performance simulations considering all spectral characteristics of the elements involved.