This will count as one of your downloads.
You will have access to both the presentation and article (if available).
The facility is compact (just 8 m x 14 m). Thanks to an innovative optical design based on an asymmetrical-cut crystal associated with a paraboloidal grazing incidence mirror, it can produce an expanded X-ray beam (170 mm x 60 mm) with low divergence (about 2 arcsec measured for the 4.51 keV beamline) at the two monochromatic energies of 4.51 keV and 1.49 keV. This allows us to calibrate each SPO MM's Effective Area and Point Spread Function precisely.
The first beamline, at 4.51 keV photon energy, is already operational, as the commissioning was completed in Q1-2023. The second beamline, at 1.49 keV energy, is being developed. It presents some more challenging aspects from both the design and implementation points of view. The monochromator stage is based on two Quartz (100); two ADP asymmetric-cut crystals (101) will provide the horizontal expansion of the beam. The X-ray source needs to be very brilliant (5 x 1011 - 1012 ph/s/sterad) due to the large fraction of photons rejected by the crystals.
This paper describes the ongoing activities. It will present the results of the 4.51 keV X-ray beamline optimization and the tests performed on a coated MM. It will also describe the progress in implementing the 1.49 keV components and discuss the comparison with other X-ray testing facilities.
A key aspect of the thin film coating development for the NewATHENA X–ray optics, is to determine the adhesion efficiency and the residual stress limitation of the coatings on silicon substrates. To do so, we magnetron sputtered different layer thicknesses of chromium layers underneath iridium/carbon bilayer and linear graded multilayer coatings. The samples were characterized using X–ray Reflectometry (XRR) to derive the thickness and micro–roughness. The residual stress was assessed by profilometry using a Dektak 150 stylus profilometer. The curvature of the samples before and after coating, along with the total film thickness derived from XRR, was used to evaluate the residual stress.
All variants are found to produce an effective area at 1 keV of around 1.24 m2, well beyond the scientific requirement of 1.1 m2. All variants are shown, when assuming a perfectly shaped and aligned mirror that is perfectly smooth, to have an intrinsic PSF that is an order of magnitude below the scientific requirement. Comparing these intrinsic PSF’s, the secondary polynomial performs best at energies below 7.5 keV. Above this energy, the equal polynomial variant performs best. A phenomenon is also shown where shifting destructive interference causes periodic peaks and troughs in the PSF HEW of individual rings of the optics, though this effect is not seen in the PSF HEW of the entire optics.
XRR scans provide detailed insights into thin film properties, however, the dependence on accurate a priori knowledge necessitates a robust model for solving the inverse problem. Addressing this limitation, XPS proves invaluable in revealing the chemical composition of thin films, improving the accuracy of the XRR model. Combined characterization through OM and XRR is very useful to find visual insights into surface contamination-induced changes when mirrors are stored for long periods in a clean room environment, as might be the case for some astronomical missions. The synergy among these techniques is pivotal for evaluating coating quality for high-energy astronomical telescopes, with a specific focus on NewAthena and upcoming missions. This research not only advances methodologies in this field but also highlights the collaborative power of XRR, XPS, and OM in providing a comprehensive understanding of thin film coatings, emphasizing the importance of pre-coating mirror quality and mitigating contamination effects throughout the optics production process to ensure optimal performance.
We present in this paper the status of the optics production and illustrate not only recent X-ray results but also the progress made on the environmental testing, manufacturing and assembly aspects of SPO based optics.
The Silicon Pore Optics (SPO) enables the NewAthena mission, delivering an unprecedented combination of good angular resolution, large effective area and low mass. The SPO technology builds significantly on spin-in from the semiconductor industry and is designed to allow a cost-effective flight optics implementation, compliant with the programmatic requirements of the mission.
The NewAthena X-ray optics is highly modular, consisting of hundreds of compact mirror modules arranged in concentric circles and mounted on a metallic optical bench. All aspects of the optics are being developed in parallel, from the industrial production of the mirror plates, over the highly efficient assembly into mirror modules, to the alignment of the mirror modules and their fixation on the optical bench. Dedicated facilities are being built to measure the performance of the NewAthena X-ray telescope optics, demonstrating their compatibility with the environmental and scientific requirements.
An overview is provided of the activities preparing the implementation of the NewATHENA optics.
In this paper we present our current state-of-the-art SPO plate manufacturing process. Special attention is given to the recent advancements in optimizing and upscaling the dicing process, the laser-ID labelling process, wafer-scale automated measurements of plate critical to quality parameters, as well as the lithography process for reflective coating lift-off. Furthermore, the different wedging methodologies and the shift from wetbench processing to spray processing are introduced. The combined efforts in all of these areas enable a more automated plate manufacturing process, and an increase in optical performance of the telescope.
Using a combination of process development and upgraded machinery, the future flight production scenario for NewATHENA begins to take shape.
The next generation x-ray observatory ATHENA (advanced telescope for high energy astrophysics) requires an optics with unprecedented performance. It is the combination of low mass, large effective area and good angular resolution that is the challenge of the x-ray optics of such a mission. ATHENA is the second large class mission in the science programme of ESA, and is currently in a reformulation process, following a design-to-cost approach to meet the cost limit of an ESA L-class mission.
The silicon pore optics (SPO) is the mission enabler being specifically developed for ATHENA, in a joint effort by industry, research institutions and ESA. All aspects of the optics are being addressed, from the mirror plates and their coatings, over the mirror modules and their assembly into the ATHENA telescope, to the facilities required to build and test the flight optics, demonstrating performance, robustness, and programmatic compliance.
The SPO technology is currently being matured to the level required for the adoption of the ATHENA mission, i.e., the start of the mission implementation phase. The monocrystalline silicon material and pore structure of the SPO provide these optics with excellent thermal and mechanical properties. Benefiting from technology spin-in from the semiconductor industry, the equipment, processes, and materials used to produce the SPO are highly sophisticated and optimised.
The preparations are ongoing at PANTER, ESA, cosine and Media Lario to perform complex opto-thermo-mechanical tests of the two full scale 1/6th sectors of the final ATHENA mirror assembly structure produced by the potential ATHENA primes Airbus Defence and Space and Thales Alenia Space. For these tests a set of three SPO MMs have been produced following the flight configuration. The MMs will be incorporated into the full scale 1/6th sectors to measure the impact of thermal gradients on the thermoelastic deformation of the structure and therefore the HEW performance. A description of the tests is presented here.
PANTER is also involved in the development, testing, and fabrication of the mirror adapter structure (MAS) to support the 2.6-m diameter ATHENA mirror assembly module demonstrators (MAMD) during the planned x-ray tests at XRCF. A description of the PANTER tests and results will be presented in this paper together with a short overview of the MAS MGSE for XRCF.
ESA’s Athena mission will use silicon pore optics, in which the optics assembly consists of pairs of mirror plates stacked into mirror modules. This paper presents a study of the angular resolution of Athena, using several candidate variants of mirror curvature and wedging. Results were achieved by ray-tracing these variants of Athena’s optics with the ray-tracing software SPORT.
The study shows that all polynomial variants yield a PSF below 1” on-axis, at all energies between 0.1 and 12 keV. The secondary-only polynomial variants perform best, for both on- and off-axis point sources. Of these variants, the wedging 0/2 variant is shown to generally yield superior angular resolution at higher energies, the -1/1 variant at lower energies.
A ray-tracing analysis using the Crab Nebula as an observation target was also performed. A 2D Fourier analysis was applied to the resulting focal plane responses to determine their angular resolution. This analysis indicates the angular resolution of all polynomial variants to be below 1”, at all but the highest energies. It also shows, though to a lesser extent, that the secondary-only polynomial variants perform best in most circumstances. Nevertheless, this second analysis requires further investigation for a more conclusive outcome.
To overcome these limitations, we started in 2012 to design a facility aimed at generating a broad (170 x 60 mm2), uniform and low-divergent (1.5 arcsec HEW) X-ray beam within a small lab (∼ 9 x 18 m2), to characterize the ATHENA MM. BEaTriX (the Beam Expander Testing X-ray facility) makes use of an X-ray microfocus source, a paraboloidal mirror, a crystal monochromation system, and an asymmetrically-cut diffracting crystal for the beam expansion. These optical components, in addition to a modular low-vacuum level (10-3 mbar), enable to match the ATHENA SPO acceptance requirements.
The realization of this facility at INAF-OAB in Merate (Italy) is now on going. Once completed, BEaTriX can be used to test the Silicon Pore Optics modules of the ATHENA X-ray observatory, as well as other optics, like the ones of the Arcus mission. In this paper we report the advancement status of the facility.
One activity has centred on the use of coated, silicon wafers, patterned with ribs, that are integrated onto a mandrel whose form has been polished to the required shape. The wafers follow the shape precisely, forming pore sizes in the sub-mm region. Individual stacks of mirrors can be manufactured without risk to, or dependency on, each other and aligned in a structure from which they can also be removed without hazard. A breadboard is currently being built to demonstrate this technology.
A second activity centres on glass pore optics. However an adaptation of micro channel plate technology to form square pores has resulted in a monolithic material that can be slumped into an optic form. Alignment and coating of two such plates produces an x-ray focusing optic. A breadboard 20cm aperture optic is currently being built.